Hotpoint Washer AQ113DA 697 S User Manual

Instructions for  
installation and use  
WASHING MACHINE  
Contents  
EN  
Installation, 2-3-4-5  
Unpacking and levelling  
EN  
Connecting the electricity and water supplies  
Technical data  
English,1  
Care and maintenance, 6  
Cutting off the water and electricity supplies  
Cleaning the machine  
Cleaning the detergent dispenser drawer  
Caring for your appliance drum  
Cleaning the pump  
Checking the water inlet hose  
Precautions and tips, 7  
General safety  
Load balancing system  
Disposal  
Opening the porthole door manually  
AQUALTIS  
Description of the machine, 8-9  
Touch control panel  
AQ113DA 697 S  
Running a wash cycle, 10  
Wash cycles and options, 11  
Table of wash cycles  
Wash options  
Detergents and laundry, 12  
Detergent  
Preparing the laundry  
Washing recommendations  
Trouble shooting, 13-14  
Assistance, 15-16  
1
 
Connecting the drain hose  
• the socket is compatible with the washing  
machines plug. If this is not the case, replace  
the socket or the plug.  
EN  
Connect the drain  
hose, without  
bending it, to a  
Your appliance is now supplied with a 13 amp  
fused plug it can be plugged into a 13 amp  
socket for immediate use. Before using the  
appliance please read the instructions below.  
draining duct or a  
wall drain situated  
between 65 and 100  
cm from the floor;  
65 - 100 cm  
WARNING - THIS APPLIANCE MUST BE  
EARTHED.  
THE FOLLOWING OPERATIONS SHOULD  
BE CARRIED OUT BY A QUALIFIED  
ELECTRICIAN.  
The drain hose may  
be connected to  
an under-sink trap.  
Before connecting  
the drain hose from  
the machine ensure  
that any blanks or  
removable ends  
Replacing the fuse:  
When replacing a faulty fuse, a 13 amp ASTA  
approved fuse to BS 1362 should always be  
used, and the fuse cover re-fitted. If the fuse  
cover is lost, the plug must not be used until a  
replacement is obtained.  
Where it connects to  
the waste water pipe  
cut end off spigot or  
remove the blanking cap  
have been taken off  
the spigot.  
Replacement fuse covers:  
If a replacement fuse cover is fitted, it must  
be of the correct colour as indicated by  
the coloured marking or the colour that is  
embossed in words on the base of the plug.  
Replacements can be obtained directly from  
your nearest Service Depot.  
If it is placed over  
the edge of a basin  
or sink be sure  
the free end of the  
hose should not be  
underwater.  
Removing the plug:  
If your appliance has a non-rewireable  
moulded plug and you should wish to re-route  
the mains cable through partitions, units etc.,  
please ensure that either:  
! We advise against the use of hose extensions;  
in case of absolute need, the extension must  
have the same diameter as the original hose  
and must not exceed 150 cm in length.  
Ensure that if the drain hose is pushed into a  
standpipe, that the end does not go down more  
than 15cms (6 inches). If the hose is pushed  
down too far, this may cause the machine to self  
-syphon ie. continuously empty as it is filling.  
the plug is replaced by a fused 13 ampere  
rewireable plug bearing the BSI mark of approval.  
or:  
the mains cable is wired directly into a 13  
amp cable outlet, controlled by a switch, (in  
compliance with BS 5733) which is accessible  
without moving the appliance.  
Disposing of the plug:  
Ensure that before disposing of the plug itself,  
you make the pins unusable so that it cannot  
be accidentally inserted into a socket.  
Electric connection  
Before plugging the appliance into the mains  
socket, make sure that:  
• the socket is earthed and in compliance  
with the applicable law;  
Instructions for connecting cable to an  
alternative plug:  
• the socket is able to sustain the appliances  
maximum power load indicated on the  
Technical Data Plate fixed on the machine.  
• the supply voltage is included within the  
values indicated on the Technical Data  
Plate fixed on the machine.  
Important: the wires in the mains lead are  
coloured in accordance with the following code:  
Green & Yellow  
Blue  
Brown  
Earth  
Neutral  
Live  
3
 
As the colours of the wires in the lead may  
not correspond with the coloured markings  
identifying the terminals in your plug, proceed  
as follows:  
! The power supply cable must only be  
EN  
replaced by an authorised serviceman.  
Warning! The company denies all liability if and  
when these norms are not respected.  
Connect Green & Yellow wire to terminal  
marked E or or coloured Green or Green &  
Yellow.  
Technical data  
Connect Brown wire to terminal marked L or  
coloured Red.  
Model  
AQ113DA 697 S  
Connect Blue wire to terminal marked N or  
coloured Black.  
width 59.5 cm  
If a 13 amp plug (BS 1363) is used it must be  
fitted with a  
Dimensions height 85 cm  
depth 64,5 cm  
13 amp fuse, either in the plug or adaptor or  
at the distribution board.  
Capacity  
Electrical  
from 1 to 11 kg  
If you are in any doubt regarding the electrical  
supply to your machine, consult a qualified  
electrician before use.  
please refer to the technical  
connections data plate fixed to the machine  
How to connect an alternative plug:  
The wires in this mains lead are coloured in  
accordance with the following code:  
maximum pressure  
1 MPa (10 bar)  
Water con-  
BLUE  
NEUTRAL (N)  
LIVE (L)  
EARTH (E)  
minimum pressure  
nections  
BROWN  
0.05 MPa (0.5 bar)  
drum capacity 71 litres  
GREEN & YELLOW  
up to 1600 rotations per  
minute  
Spin speed  
GREEN &  
YELLOW  
Test wash  
cycles in  
13 ampere fuse  
BROWN  
accordan-  
ce with  
programme  
;
CROSS-BAR  
CORD GRIP  
BLUE  
Cotton Standard 60°C.  
directives  
1061/2010  
and  
programme  
Cotton Standard 40°C.  
;
1015/2010  
Disposing of the appliance:  
This appliance conforms to  
the following EC Directives:  
- 2004/108/EC (Electroma-  
gnetic Compatibility)  
- 2006/95/EC (Low Voltage)  
- 2012/19/EU  
When disposing of the appliance please  
remove the plug by cutting the mains cable  
as close as possible to the plug body and  
dispose of it as described on the previous  
page.  
! The washing machine should not be installed  
in an outdoor environment, not even where  
the area is sheltered, because it may be very  
dangerous to leave it exposed to damp, rain  
and thunderstorms.  
! When the washing machine is installed, the  
mains socket must be within easy reach.  
! Do not use extensions or multiple sockets.  
! The power supply cable must never be bent  
or dangerously compressed.  
4
 
EN  
5
 
Care and maintenance  
To access the pre-chamber:  
Cutting off the water and  
electricity supplies  
EN  
Turn off the water tap after every wash cycle.  
This will limit wear on the hydraulic system in  
the machine and help to prevent leaks.  
• Unplug the appliance when cleaning it and  
during all maintenance work.  
Cleaning the machine  
1. take off the cover panel on the front of the  
machine by first pressing it in the centre and  
then pushing downwards on both sides until  
you can remove it (see figures);  
The outer parts and rubber components of the  
appliance can be cleaned using a soft cloth  
soaked in lukewarm soapy water. Do not use  
solvents or abrasives.  
2. position a container  
so that it will collect the  
water which flows out  
(approximately 1.5 l)  
(see figure);  
3. unscrew the lid by  
rotating it in an anti-  
clockwise direction (see  
figure);  
Cleaning the detergent dispenser  
drawer  
To remove the drawer,  
1
press lever (1) and pull  
the drawer outwards (2)  
1
(see figure).  
Wash it under running  
2
water; this procedure  
4. clean the inside thoroughly;  
5. screw the lid back on;  
6. reposition the panel, making sure the hooks  
are securely in place before you push it onto  
the appliance.  
should be repeated  
frequently.  
2
Caring for your appliance drum  
Checking the water inlet hose  
• Always leave the door ajar to prevent  
unpleasant odours from forming.  
Check the inlet hose at least once a year. If  
there are any cracks, it should be replaced  
immediately: during the wash cycles, water  
pressure is very strong and a cracked hose  
could easily split open.  
Cleaning the pump  
The washing machine is fitted with a self-  
cleaning pump which does not require any  
maintenance. Sometimes, small items (such  
as coins or buttons) may fall into the protective  
pre-chamber at the base of the pump.  
! Make sure the wash cycle has finished and  
unplug the appliance.  
6
 
Precautions and tips  
! The machine was designed and constructed in  
accordance with international safety regulations. The  
following information is provided for safety reasons and  
must therefore be read carefully.  
inside the machine, while preventing potential damage  
to the atmosphere and to public health.  
The crossed-out dustbin is marked on all products  
to remind the owner of their obligations regarding  
separated waste collection.  
EN  
General safety  
For more information relating to the correct disposal of  
household appliances, owners should contact their local  
authorities or appliance dealer.  
TThhiissaapppplialniacnecweascdaensibgneedusfoerddobmyescthiciludsreenonly.  
aged from 8 years and above and  
persons with reduced physical, sensory or  
mental capabilities or lack of experience  
and knowledge if they have been given  
supervision or instruction concerning use of  
the appliance in a safe way and understand  
the hazards involved. Children shall not  
play with the appliance. Cleaning and user  
maintenance shall not be made by children  
without supervision.  
Opening the porthole door manually  
In the event that it is not possible to open the porthole door  
due to a powercut, and if you wish to remove the laundry,  
proceed as follows:  
1. remove the plug from the  
electrical socket.  
2. make sure the water level  
inside the machine is lower  
than the door opening; if  
it is not, remove excess  
water using the drain hose,  
collecting it in a bucket as  
indicated in the figure.  
• Do not touch the machine when barefoot or with wet or  
damp hands or feet.  
• Do not pull on the power supply cable when unplugging  
the appliance from the electricity socket. Hold the plug  
and pull.  
• Do not touch the drained water as it may reach  
extremely high temperatures.  
• Never force the porthole door. This could damage the  
safety lock mechanism designed to prevent accidental  
opening.  
3. remove the cover panel on the lower front part of the  
washing machine (see overleaf).  
• If the appliance breaks down, do not under any  
circumstances access the internal mechanisms in an  
attempt to repair it yourself.  
• Always keep children well away from the appliance while  
it is operating.  
• If it must be moved, proceed with the help of two or  
three people and handle it with the utmost care. Never  
try to do this alone, because the appliance is very heavy.  
• Before loading laundry into the washing machine, make  
sure the drum is empty.  
4. pull outwards using the  
tab as indicated in the figure,  
until the plastic tie-rod is freed  
from its stop position; pull  
downwards until you hear a  
“click”, which indicates that  
the door is now unlocked.  
Load balancing system  
Before every spin cycle, to avoid excessive vibrations  
before every spin and to distribute the load in a uniform  
manner, the drum rotates continuously at a speed which  
is slightly greater than the washing rotation speed. If,  
after several attempts, the load is not balanced correctly,  
the machine spins at a reduced spin speed. If the load is  
excessively unbalanced, the washing machine performs  
the distribution process instead of spinning. To encourage  
improved load distribution and balance, we recommend  
small and large garments are mixed in the load.  
5. open the door; if this is  
still not possible repeat the  
procedure.  
Disposal  
6. reposition the panel, making sure the hooks are securely  
in place before you push it onto the appliance.  
• Disposing of the packaging materials: observe local  
regulations so that the packaging may be re-used.  
• The European Directive 2012/19/EU relating to Waste  
Electrical and Electronic Equipment (WEEE) states  
that household appliances should not be disposed of  
using the normal solid urban waste cycle. Exhausted  
appliances should be collected separately in order to  
optimise the cost of re-using and recycling the materials  
7
 
Description of the machine  
CONTROL  
PANEL  
EN  
PORTHOLE DOOR  
PORTHOLE DOOR  
HANDLE  
KICK STRIP  
PORTHOLE DOOR  
washing additives compartment: for fabric softener  
or liquid additives. We recommend that the maximum  
level indicated by the grille is not exceeded, and that  
concentrated fabric softeners are diluted.  
Always use the handle to  
open the porthole door (see  
figure).  
TOUCH CONTROL PANEL  
To adjust the settings, gently  
press the icon inside the  
sensitive (touch control) area  
as illustrated in the figure.  
DETERGENT DISPENSER DRAWER  
The detergent dispenser  
drawer is located inside  
the machine and can be  
accessed by opening the  
door.  
For more information on  
detergent measures, please  
refer to the chapter entitled  
“Detergents and laundry”.  
Standby mode  
This washing machine, in compliance with new energy  
saving regulations, is fitted with an automatic standby  
system which is enabled after about 30 minutes if no  
activity is detected. Press the ON-OFF  
wait for the machine to start up again.  
button briefly and  
! Do not pour detergent into  
the compartment 1.  
A
Detergent should only be  
poured into the compartment 2.  
1
2. main wash compartment:  
If liquid detergent is used,  
it is recommended that the  
removable plastic partition A  
(supplied) be used for proper  
dosage.If powder detergent is  
2
B
used, place the partition into slot B.  
8
 
START/PAUSE button  
Touch control panel  
EN  
with indicator light  
SPIN  
WASH  
button  
CYCLE  
PHASE  
icons  
WASH CYCLE  
M1  
ECO  
indicator light  
M2  
TEMPERATURE  
SELECTOR knob  
button  
DISPLAY  
CHILD LOCK button  
with indicator light  
OPTION  
buttons  
Button with ON/OFF  
indicator light  
DELAYED START  
button  
M3  
LOCK indicator light  
lit in a fixed manner. To pause the wash cycle, press the  
button again; the indicator light will flash in an orange colour. If  
the “LOCK” indicator light is switched off, the door may be  
opened. To start the wash cycle from the point at which it was  
interrupted, press the button again.  
Button with  
ON/OFF indicator light: press this briefly  
to switch the machine on or off. The green indicator light  
indicates that the machine is switched on. To switch off the  
washing machine during the wash cycle, press and hold the  
button for approximately 3 seconds; if the button is pressed  
briefly or accidentally the machine will not switch off. If the  
machine is switched off during a wash cycle, this wash cycle  
will be cancelled.  
LOCK indicator light: indicates that the porthole door is  
locked. To open the door, pause the wash cycle (see “Running  
a wash cycle”).  
WASH CYCLE SELECTOR knob: may be turned in either  
direction. To select the most suitable wash cycle, please refer  
to the Table of wash cycles”.  
CHILD LOCK  
button with indicator light: to activate  
or deactivate the CHILD LOCK, press and hold the button  
for approximately 2 seconds. when the indicator light  
is illuminated, the control panel is locked. This means it  
is possible to prevent wash cycles from being modified  
accidentally, especially where there are children in the home.  
The knob will not move during the wash cycle.  
M1-M2-M3 buttons: press and hold one of the buttons to  
store a cycle with your own set preferences in the memory  
of the machine. To recall a previously-stored cycle, press the  
corresponding button.  
ECO indicator light: the  
icon lights up when, after altering  
the washing parameters, an energy saving of at least 10%  
is made. Furthermore, before the machine enters “Standby”  
mode, the icon will light up for a few seconds; when the  
machine is switched off the estimated energy saving will be  
around the 80% mark.  
TEMPERATURE  
button: press to modify or exclude the  
temperature setting; the value selected will appear on the  
display above (see “Running a wash cycle”).  
SPIN CYCLE  
button: press to modify or exclude the spin  
cycle; the value selected will appear on the display above (see  
“Running a wash cycle”).  
DELAYED START  
button: press to set a delayed start for  
the selected wash cycle; the set delay time will appear on the  
display above (see “Running a wash cycle”).  
OPTION buttons: press to select the available options. The  
indicator light corresponding to the selected option will remain  
lit (see “Running a wash cycle”).  
WASH CYCLE PHASE icons: these illuminate to indicate the  
progress of the wash cycle (Wash  
– Rinse  
– Spin  
Drain ). The text lights up when the cycle is complete.  
START/PAUSE button with indicator light: when the green  
indicator light flashes slowly, press the button to start a wash  
cycle. Once the cycle has begun the indicator light will remain  
9
 
Running a wash cycle  
WARNING: before you use the washing machine for the  
first time, run a wash cycle with detergent and no laundry,  
using the 90° cottons cycle.  
remaining until the end of the cycle. To remove the  
delayed start option, press the button until the display  
shows the text OFF; the symbol will disappear.  
EN  
1. SWITCH THE MACHINE ON. Press the  
button. All  
Modify the cycle settings.  
• Press the button to activate the option; the name  
of the option will then appear on the display and  
the corresponding indicator light will illuminate.  
• Press the button again to deactivate the option; the  
name of the option will then appear on the display  
followed by the text OFF, and the corresponding  
indicator light will switch off.  
! If the selected option is not compatible with the  
selected wash cycle, this incompatibility will be signalled  
by the flashing of the indicator light and a sound alert  
(3 beeps); the option will not be activated.  
! If the selected option is not compatible with another  
option that has been selected previously, the indicator  
light corresponding to the first option selected will  
flash and only the second option will be activated; the  
indicator light corresponding to the button will remain lit  
in a constant manner.  
the indicator lights will illuminate for 1 second and the  
text AQUALTIS will appear on the display; the indicator  
light corresponding to the  
button will then remain lit in  
a constant manner and the START/PAUSE indicator light  
will flash.  
2. SELECT THE PROGRAMME. Turn the PROGRAMME  
KNOB left or right, until the required programme has  
been selected; the name of the programme will appear  
on the display. A temperature and spin speed is set for  
each programme; these may be adjusted. The cycle  
duration will also appear on the display.  
3. LOAD THE LAUNDRY. Open the porthole door.  
Load the laundry, making sure you do not exceed the  
maximum load value indicated in the table of wash  
cycles on the following page.  
4. MEASURE OUT THE DETERGENT. Pull out the  
detergent dispenser drawer and pour the detergent into  
the relevant compartments as described in “Description  
of the machine”.  
! The options may affect the recommended load value and/  
or the duration of the cycle.  
7. START THE PROGRAMME. Press the START/PAUSE  
button. The corresponding indicator light remains lit in a  
fixed manner and the porthole door locks (the LOCK  
indicator light illuminates). The icons corresponding  
to the wash cycle phases will light up during the cycle  
to indicate which phase is currently in progress. To  
change a wash cycle once it has already started, pause  
the washing machine by pressing the START/PAUSE  
button; then select the desired cycle and press the  
START/PAUSE button again. To open the door during  
a wash cycle, press the START/PAUSE button; if the  
LOCK indicator light is switched off you may open  
the door. Press the START/PAUSE button again to  
restart the wash cycle from the point at which it was  
interrupted.  
5. CLOSE THE PORTHOLE DOOR.  
6. CUSTOMISE THE WASH CYCLE. Use the relevant  
buttons on the control panel:  
Modify the temperature and/or spin speed.  
The machine automatically displays the maximum  
temperature and spin speed values set for the selected  
cycle, or the most recently-used settings if they are  
compatible with the selected cycle. The temperature can  
be decreased by pressing the  
wash “OFF” setting is reached. The spin speed may be  
progressively reduced by pressing the button, until  
button, until the cold  
it is completely excluded “OFF”. If these buttons are  
pressed again, the maximum values are restored.  
! Exception: if the  
programme is selected, the  
temperature can be increased up to a value of 90°C.  
8. THE END OF THE WASH CYCLE. This is indicated  
by the illuminated text END. The porthole door may be  
opened immediately. If the START/PAUSE indicator light  
is flashing, press the button to end the cycle. Open the  
door, unload the laundry and switch off the machine.  
Setting a delayed start.  
To set a delayed start for the selected cycle, press the  
corresponding button repeatedly until the required delay  
period has been reached. During the setting procedure,  
the delay period and the text “Starts in:” will be  
displayed, along with the flashing  
delayed start has been set, the  
! If you wish to cancel a cycle which has already begun,  
press and hold the  
button until the cycle stops and the  
symbol. After the  
symbol will remain  
machine switches off.  
fixed on the display, which will also indicate the duration  
of the selected cycle with the text “Ends in:” and the  
cycle duration. Press the DELAYED START button just  
once to display the delay time set previously.  
After the countdown has begun, the display will show  
the text “Starts in:” and the delay period. Once the  
set delay time has elapsed, the machine will begin its  
cycle and the display will show “Ends in:” and the time  
Bag for quilts, curtains and delicate garments  
The Aqualtis washing machine makes it easier for you  
to wash even the most valuable and delicate garments  
in complete confidence thanks to the special bag which  
protects the laundry (this is supplied with the machine).  
We recommend that the bag is used every time you wash  
quilts and padded items with an outer layer made  
using synthetic material.  
10  
 
Wash cycles and options  
Table of wash cycles  
EN  
Detergent and  
additives  
Max.  
temp.  
(°C)  
Max.  
speed  
(rpm)  
Description of the wash cycle  
-
5
5
48 0,99 57 120’  
48 0,63 55 100’  
Synthetics Resistant  
Synthetics Resistant (3)  
Whites  
60°  
40°  
60°  
40°  
30°  
-
800  
800  
1600  
1600  
800  
-
-
-
-
-
190’  
6
44 0,99 92 125’  
Coloureds  
6
-
-
-
-
-
-
-
-
-
-
-
-
80’  
20’  
Darks  
6
Steam Refresh  
2
3,5  
11  
145’  
160’  
Duvets: for down-stuffed garments.  
Bed&Bath for bedlinen and towels.  
30°  
60°  
1200  
1600  
11  
11  
-
-
-
-
-
-
49’  
16’  
Rinse  
-
-
1600  
1600  
-
-
Spin and Pump out  
-
Anti Allergy  
60°  
30°  
40°  
1600  
0
6
1
-
-
-
-
-
-
-
-
-
205’  
80’  
Ultradelicates  
100’  
Wool: for wool, cashmere, etc.  
800  
2,5  
Mix 30': to refresh lightly soiled garments quickly (not suitable for wool,  
silk and clothes which require washing by hand).  
4
71 0,21 41  
30’  
30°  
800  
60°  
(Max. 90°)  
Cotton Standard 60°C (1): heavily soiled whites and resistant colours.  
1600  
11  
44 1,38 62,5 215’  
44 1,19 90 195’  
Cotton Standard 40°C (2): lightly soiled whites and delicate colours.  
Cotton Standard 20°C: lightly soiled whites and delicate colours.  
40°  
1600  
1600  
11  
11  
20°  
-
-
-
175’  
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-  
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.  
Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this value  
will then be shown on the display.  
1) Test wash cycle in compliance with directive 1061/2010: set wash cycle  
with a temperature of 60°C.  
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for  
garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.  
2) Test wash cycle in compliance with directive 1061/2010: set wash cycle  
with a temperature of 40°C.  
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should be used for  
garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.  
For all Test Institutes:  
2) Long wash cycle for cottons: set wash cycle  
with a temperature of 40°C.  
3) Long wash cycle for synthetics: set wash cycle with a temperature of 40°C.  
Wash options  
Steam Hygiene  
Time Saver  
This option enhances washing performance by generating  
steam during the wash cycle that eliminates any bacteria  
from fibres while treating them at the same time. Place the  
laundry in the drum, choose a compatible programme and  
select option “ “.  
! The steam generated during washing machine operation  
may cause the porthole door to become hazy.  
If you select this option, the wash cycle duration will be  
reduced by up to 50%, depending on the selected cycle,  
thereby guaranteeing simultaneous water and energy  
saving. Use this cycle for lightly soiled garments.  
! It cannot be used in conjunction with  
,
,
,
,
,
,
,
,
.
! It cannot be used in conjunction with  
(90°).  
,
,
,
,
,
Eco  
,
,
,
,
The Eco Option saves energy by not heating the water  
used to wash your laundry – an advantage both to the  
environment and to your energy bill. Instead, intensified  
wash action and water optimisation ensure great wash  
results in the same average time of a standard cycle.  
For the best washing results we recommend the usage of a  
liquid detergent.  
Easy Iron  
By selecting this option, the wash and spin cycles will be  
modified in order to reduce the formation of creases.  
At the end of the cycle the washing machine drum will  
rotate slowly; the “Easy Iron” and START/PAUSE indicator  
lights will flash. To end the cycle press the START/PAUSE  
button or the “Easy Iron” button.  
! It cannot be used in conjunction with  
,
,
,
,
,
,
,
,
,
,
.
! It cannot be used in conjunction with  
,
,
,
,
,
,
.
11  
 
Detergents and laundry  
into the drum together with the laundry. Then launch the specific  
programme “ “. At the end of the cycle, garments will be  
relaxed and fragrant.  
! Not recommended for wool or silk garments.  
! Do not add too much perfume to the sponge in order to  
avoid it dripping.  
Detergent  
EN  
The type and quantity of detergent required depend on  
the type of fabric you are washing (cotton, wool, silk, etc.),  
as well as its colour, the washing temperature, the level of  
soiling and the hardness of the water in the area.  
Measuring out the detergent carefully will avoid wastage and help  
to protect the environment: although they are biodegradable,  
detergents still contain ingredients which alter the balance of nature.  
We recommend the following:  
! Do not add softeners or detergents.  
Duvets: to wash double or single duvets (the weight of  
which should not exceed 3,5 kg), cushions or clothes  
padded with goose down such as puffa jackets, use the  
• use powder detergents for white cotton garments and  
pre-washing.  
• use liquid detergents for delicate cotton garments and for  
all low-temperature wash cycles.  
• use gentle liquid detergents for wool and silk garments.  
The detergent should be poured into the relevant compartment - or  
the dispenser placed directly inside the drum - before the wash  
cycle begins. In the latter case, it will not be possible to select the  
Cottons with pre-wash cycle.  
special  
wash cycle. We recommend that duvets are  
placed in the drum with their edges folded inwards (see  
figure) and that no more than ¾ of the total volume of the  
drum is used. To achieve the best results, we recommend  
that a liquid detergent is used and placed inside the  
detergent dispenser drawer.  
! Do not use hand washing detergents because these create  
too much foam.  
! Use powder detergent for white cotton garments, for pre-  
washing, and for washing at temperatures over 60°C.  
! Follow the instructions given on the detergent packaging.  
Preparing the laundry  
• Shake out the garments before loading them into the  
machine.  
Quilts: to wash quilts with a synthetic outer layer, use  
• Divide the laundry according fabric type (symbol on the  
washing instruction label) and colour, making sure you  
separate the coloured garments from the white ones;  
• Empty all pockets and check the buttons;  
• Do not exceed the values listed in the Table of wash cycles”,  
which refer to the weight of the laundry when dry.  
the bag provided and set the wash cycle to  
.
Bed&Bath: Use programme to wash bed linen and  
towels in one single cycle: it optimises softener performance  
and helps you save time and energy. We recommend the use  
of powder detergent  
Anti Allergy: use programme  
to remove major allergens  
such as pollen, mites, cats and dogs hair.  
How much does your laundry weigh?  
Ultradelicates: use programme  
to wash very delicate  
1 sheet  
400-500 g  
150-200 g  
400-500 g  
900-1200 g  
150-250 g  
400-500 g  
150-200 g  
garments with decorative features, such as diamantes and  
sequins. We recommend turning the garments inside out  
before washing and placing small items into the special  
bag for washing delicates. Use liquid detergent on delicate  
garments for best results.  
1 pillowcase  
1 tablecloth  
1 bathrobe  
1 towel  
1 pair of jeans  
1 shirt  
To wash Silk garments and Curtains (these should be folded  
and placed inside the bag provided), select cycle  
and then  
option  
is soaking and the  
water so that the laundry may be removed, press the START/  
PAUSE button or the button.  
; the machine will end the cycle while the laundry  
Washing recommendations  
indicator light will flash. To drain the  
Whites: use this cycle  
to wash white clothes. The  
programme is designed to maintain the brightness of white  
clothes over time.  
Wool: the wool wash cycle on this Hotpoint machine has  
been tested and approved by The Woolmark Company for  
washing wool garments labelled as hand washable provided  
that the garments are washed according to the instructions on  
the garment label and those issued by the manufacturer of this  
washing machine. Hotpoint is the first washing machine brand  
to be approved by The Woolmark Company for Apparel  
Care- Platinum for its washing performance and consumption  
of energy and water. (M1135)  
Coloureds: use this cycle  
clothes. The programme is designed to maintain bright  
colours over time.  
to wash bright coloured  
Darks: Use cycle  
to wash dark-coloured garments. This  
programme is designed to maintain dark colours over time.  
We recommend using a liquid detergent for the best results  
when washing dark-coloured garments.  
Steam Refresh: this programme refreshes garments by  
removing bad odours and relaxing the fibres (2 kg, roughly  
3 items). Insert dry items only (that are not dirty) and select  
programme “  
“. The garments will be damp once the cycle  
Cotton Standard 20°: ideal for lightly soiled cotton  
loads. The effective performance levels achieved at cold  
temperatures, which are comparable to washing at 40°, are  
guaranteed by a mechanical action which operates at varying  
speed, with repeated and frequent peaks.  
is completed, so we recommend hanging them to dry. The “  
“ programme makes ironing easier. Moreover, with the  
“Steam Perfume” laundry balls, your favourite perfume can be  
added to your laundry. Place a few drops of perfume on the  
sponge contained inside the laundry ball, close it and insert it  
12  
 
Trouble shooting  
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre (see “Assistance”),  
make sure that the problem cannot be solved easily using the following list.  
EN  
Problem:  
Possible causes / Solutions:  
The machine does not switch on.  
• The appliance is not plugged into the socket fully, or not enough to make contact.  
• There is no power to the socket, or the fuse has blown in the mains plug.  
The wash cycle does not start.  
• The door is not closed properly.  
• The ON/OFF button has not been pressed.  
• The START/PAUSE button has not been pressed.  
• The water tap has not been turned on to allow water to flow into the machine.  
• The ‘DELAY TIMER’ has been selected.  
• The ‘CHILD LOCK’ is activated (see ‘The machine just ‘beeps’ when a  
programme or option is selected’ below).  
The machine does not fill with  
• The water inlet hose is kinked.  
water or Indicator light for the first • The water inlet hose is not connected to the water supply.  
wash cycle flashing rapidly.  
• The water pressure is too low.  
• The water tap has not been turned on to allow water to flow into the machine.  
• There is no water supply to the house.  
• The inlet valve filter is blocked.  
• The START/PAUSE button has not been pressed.  
The machine continuously fills with • The top of the drain hose is too low - It must be fitted at a height between 65  
water and continually drains away  
or Water left in the drum  
or Stuck on wash.  
and 100 cm from the floor (see “Installation”).  
• The drain hose is connected incorrectly to the sink trap allowing water to run  
into the machine, the drain hose must be positioned higher than the bottom of  
the sink to prevent water flowing down the drain hose.  
• The end of the drain hose has been pushed too far down the standpipe, the  
‘U’ bracket should be fitted 100 mm from the end of the drain hose.  
The machine does not drain or spin • The Pump filter is blocked.  
- (error lights flashing).  
• The drain hose is kinked (see “Installation”).  
New Installation - The blanking cap or spigot has not been removed if  
connected under a sink.  
• The drain hose or sink trap is blocked.  
The machine does not spin.  
• The Spin Speed is set to “OFF” position.  
The machine does not drain or spin • The ‘EASY IRON’ option is enabled at the end of the program the machine  
- ‘EASY IRON’ light flashes.  
drum will rotate slowly. To complete the wash cycle press the ‘START/PAUSE’  
or the ‘EASY IRON’ buttons (see Wash Cycles & Options).  
• The ‘SILK’ program is selected, at the end of the program it requires the drain  
phase to be started. To complete the program press either the ‘START/PAUSE’  
or ‘EASY IRON’ buttons (see Wash Cycles & Options).  
• Programme times will vary due to water pressure, the incoming water  
temperature and if the wash load goes out of balance. This will increase the  
programme times accordingly (see ‘ The machine wont spin properly’ below).  
The programme takes too long.  
• Programme times will vary due to water pressure, the incoming water  
temperature and if the wash load goes out of balance. This will increase the  
programme time accordingly (see ‘The machine wont spin properly’ below)  
- (Most Common Cause!)  
The Display sticks at one ‘time to  
end’ for more than 1 Minute or the  
Display changes the estimated ‘Time  
to End’ during the programme.  
• The display time is for guidance only - it is not a precise time to finish and  
may vary.  
The machine vibrates a lot during  
the spin cycle.  
• The feet have not been adjusted, enabling the machine to rock.  
New Installation - Either the Transit Bolts including the plastic spacers, or the  
Polystyrene Packaging have not been removed when installing the machine.  
• The machine is trapped between cabinets and/or walls.  
• The load is in a slight out of balance condition and machine is spinning, but at  
a lower speed.  
13  
 
The machine is noisy.  
• There will always be some motor, pump and drum noise during spin.  
EN  
The machine wont spin properly.  
• Out of Balance detected when attempting to go into a spin cycle - If this  
happens the machine will continue to try to repeat the distribution of the load  
required before the machine will go into higher spin speeds - This will increase  
the programme time accordingly. This is a safety feature to prevent damage.  
Out of Balance can be caused by washing a single heavy item (eg duvet, quilt,  
etc). - Try the programme again using a different load.  
The machine leaks from the  
dispenser.  
• The dispenser drawer is blocked with detergent and requires cleaning.  
• The water pressure is too high and requires turning down - turn down the tap  
on the water supply pipe slightly and try again.  
• The machine is tilting forwards - It must be level when in its final position.  
The machine leaks (other than  
dispenser).  
• The fill hose is loose, check both the cabinet and tap ends.  
• The fill hose is tight but still leaks, if so replace the rubber washers, or the fill  
hose is missing the rubber washer.  
• The drain hose is not fixed in properly.  
The Phase in Progress indicator  
lights flash rapidly at the same  
time as the ON/OFF indicator light.  
• Switch off the machine and unplug it, wait for approximately 1 minute and then  
switch back on again. If the problem persists contact Technical Assistance  
Centre.  
The machine smells.  
• The machine requires a service wash. Run a 60 degree wash cycle with  
detergent and no laundry.  
The machine door cannot be  
opened.  
• The door will not open until the door lock indicator light goes out shortly after  
the program has finished.  
• If there is no power to the machine you need to perform the manual unlocking  
procedure (see Precautions & Tips).  
Door Seal damaged at the bottom.  
• The door seal has drainage holes at the bottom - This is normal.  
• The water level is correct if it can be seen at the bottom of the door.  
The water level is too low when  
the machine is washing.  
The word ‘DEMO’ appears  
intermittently in the display  
window and the drum slowly turns.  
To exit, switch machine off, then press and hold ‘START/PAUSE’ and ‘ON/OFF’  
buttons simultaneously for 3 seconds. Note the machine will need the language  
resetting.  
The machine just ‘beeps’ when a  
programme or option is selected  
(Child Lock Symbol is lit).  
• Deactivate the Child Lock feature by pressing and holding in the ‘CHILD  
LOCK’ button for 2 seconds.  
Clothes are coming out too wet on  
‘Steam Refresh’ cycle.  
• Only dry items are to be used for this program. The program refreshes  
garments by removing bad odours and relaxing the fibres, also making items  
easier to iron if required.  
There is too much foam.  
• The detergent is not suitable for machine washing (it should display the text  
‘for washing machines’ or ‘hand and machine wash’ or the like).  
Too much detergent was used - less detergent is required in soft water.  
After completing the programme,  
or before starting a programme,  
the machine has turned itself off  
(no lights).  
To comply with new energy saving regulations the machine is fitted with an  
automatic standby system. Press ‘ON/OFF’ button for 3 seconds to activate  
the machine, it can then either be switched off or a new programme selected.  
General.  
Your washing machine contains sensors that monitor progress during the wash  
cycle (eg: Water Levels, Temperatures, Out of Balance loads, Wash time/progress).  
Normally, if your machine successfully completes the cycle, there is unlikely to  
be anything wrong!  
Remember, you will be charged for a service call for problems caused by incorrect installation, as  
indicated on pages 2 to 4.  
Not emptying contents from pockets may cause pump or drain blockages, or may damage the machine.  
Do not wash items which do not have a wash label, or wash items that are not intended as machine washable.  
14  
 
Assistance  
Guarantee  
12 Months Parts and Labour Guarantee  
EN  
Your appliance has the benefit of our manufacturers guarantee, which covers the cost of breakdown  
repairs for twelve months from the date of purchase.  
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of  
either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no cost  
to you.  
This guarantee is subject to the following conditions:  
-
The appliance has been installed and operated correctly and in accordance with our  
operating and maintenance instructions.  
-
-
-
The appliance is used only on the electricity or gas supply printed on the rating plate.  
The appliance has been used for normal domestic purposes only.  
The appliance has not been altered, serviced, maintained, dismantled, or otherwise  
interfered with by any person not authorised by us.  
-
-
-
Any repair work must be undertaken by us or our appointed agent.  
Any parts removed during repair work or any appliance that is replaced become our property.  
The appliance is used in the United Kingdom or Republic of Ireland.  
The guarantee does not cover:  
-
-
-
Damage resulting from transportation, improper use, neglect or interference or as a result  
of improper installation.  
Replacement of any consumable item or accessory . These include but are not limited to: plugs,  
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.  
Replacement of any removable parts made of glass or plastic.  
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL  
OR NON-DOMESTIC PREMISES.  
5 Year Parts Guarantee  
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you  
registering your appliance with us and the parts being fitted by one of our authorised engineers. There will  
be a charge for our engineers time. To activate the extra parts warranty on your appliance, simply call our  
registration line on 08448 24 24 24 (ROI 01 230 0800).  
Extended Guarantees  
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense of repair  
bills for the life of your policy. To find the ideal plan for you please call our advice line on  
08448 226 226 (Republic of Ireland 01 230 0233).  
Free Helpdesk Service  
We have a dedicated team who can provide free advice and assistance with your appliance if you  
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint Service  
Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone assistance, or, where  
necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will replace  
your machine or, if you prefer, give you your money back.  
15  
 
195116926.01  
12/2013  
-
Xerox Fabriano  
After Sales Service  
No one is better placed to care for your Hotpoint appliance during the course of its working  
life than us - the manufacturer.  
EN  
Essential Contact Information  
Hotpoint Service  
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and 1000  
fully qualified engineers on call to ensure you receive fast, reliable, local service.  
UK: 08448 224 224  
Republic of Ireland: 0818 313 413  
Please note: Our advisors will require the following information:  
Model number:  
Serial number:  
Parts and Accessories  
We supply a full range of genuine replacement parts as well as accessory products that protect and  
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.  
UK: 08448 225 225  
Republic of Ireland: 0818 313 413  
Appliance Registration  
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts guarantee  
you must register your appliance with us.  
UK: 08448 24 24 24  
Republic of Ireland: 01 230 0800  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB  
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17  
Recycling & Disposal Information  
As part of Hotpoints continued commitment to helping the environment, Hotpoint reserves the right to use  
quality, recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children, remove the  
door, plug and cut the mains cable off flush with the appliance. Dispose of these parts separately to ensure  
that the appliance can no longer be plugged into a mains socket, and the door cannot be locked shut.  
16  
 

Graco Stroller ISPC090BB User Manual
Havis Shields Automobile Accessories E 250 E 350 User Manual
Hawking Technology Network Card HWUG1 User Manual
Heatiator Indoor Fireplace Rave4013i c User Manual
Honeywell Thermostat 8162 User Manual
HP Hewlett Packard Laptop 5000C CT User Manual
HP Hewlett Packard Network Router HP 30 Coax User Manual
HP Hewlett Packard Personal Computer 120 113 User Manual
HP Hewlett Packard Surge Protector A0610 User Manual
Hubbell Switch 31200 User Manual