PROFESSIONAL
MULTI
HAIR TRIMMER
MT 6741
_________________________________________________________
1
5
9
2
3
4
6
7
8
10
11 12
13
14
3
SAFETY___________________________________
7
Please note the following instructions
when using the appliance.
Always disconnect the power
supply unit if the appliance is
not being charged or used.
7
The appliance is designed for
7
7
7
domestic use only.
Never use the appliance if it is
visibly damaged.
7
Observe these instructions in
order to prevent damage to the
appliance or danger arising
from improper use. Keep them
in a safe place.
Keep the appliance away from
children.
The appliance may not be used
by the following people, includ-
ing children: those with limited
physical, sensory or mental
capabilities and also those with a
lack of experience and know-
ledge. This does not apply to the
latter if they were instructed in
the use of the appliance or if
they use it under the supervision
of a person responsible for safe-
ty. Children should always be
supervised to ensure that they do
not play with the appliance.
7
Never use the appliance in the
bath, shower or over a wash
basin filled with water; nor should
it be operated with wet hands.
7
Do not immerse the appliance in
water or let it come into contact
with water, even during
cleaning.
7
Do not open the appliance under
any circumstances. No warranty
claims are accepted for damage
resulting from improper handling.
7
Do not drop the appliance.
7
If not already present, for addi-
tional protection it is recommend
to install a residual-current-oper-
ated protective device (RCD)
with a rated residual operating
current not exceeding 30 mA in
the electrical circuit of your bath-
room. Ask your electrician for
advice.
ENGLISH
4
OVERVIEW _______________________________
Dear customer,
Special features
This appliance has five separate
functions:
Congratulations on the purchase of
your MT 6741 multi-hair trimmer.
– precise hair cutting at a width of
38 mm.
Read the following user notes care-
fully to ensure you can enjoy your
quality product from Grundig for
many years to come.
– precise beard trimming at a width
of 30 mm.
The high-quality and professional
styling appliances in the new prod-
uct range fulfil the highest standards
for salon results at home.
– hair or beard trimming with
various cutting lengths (2, 4, 8,
12, 16, 20 mm) at widths of
38 mm or 30 mm.
– thinning out hair.
– close shaving.
A responsible approach!
GRUNDIG focuses on
contractually agreed
social working conditi-
ons with fair wages for
both internal employees and supp-
liers, as well as on the efficient use
of raw materials with continual
waste reduction of several tonnes of
plastic each year – and availability
of at least 5 years for all accessories.
For a future worth living.
For a good reason. Grundig.
ENGLISH
5
OVERVIEW _______________________________
Controls
Accessories
See the illustrations on pages 2
and 3.
1
to
Six comb attachments for
various cutting lengths
(2 to 20 mm), suitable for
both cutting heads.
6
7
8
A
B
Professional cutting head
made from ceramic/stainless
steel (width 38 mm).
Attachment for thinning out
hair.
Side catches for removing
attachments.
Shaving attachment with
single blade foil for a smooth
shave.
C
On/off switch.
D
Charging display (LED). Lights
up red when charging and
green when it is fully charged.
9
Beard trimming attachment
(width 30 mm).
10 Power supply unit.
11 Cleaning brush.
12 Oil.
E
F
Socket for plugging into the
charging unit or connecting the
power supply unit.
Charging unit.
13 Comb.
14 Storage case.
ENGLISH
6
POWER SUPPLY __________________________
Notes
Rechargeable battery
7
Charge up the batteries complete-
operation
ly before you use them for the
When operating the appliance with
first time or if you have not used
the built-in nickel metal hydride bat-
them for a long time (approx. 24
tery, only use the power unit sup-
hours’ timer-controlled charging).
plied for charging.
D
– The charging display
lights
up red when charging and
changes to green when it is
fully charged.
Check that the voltage indicated on
the type plate of the power supply
unit corresponds to your local
power supply.
7
After the batteries are first char-
ged, the charging time is approx.
12 hours when the appliance is
switched off. If you switch on the
appliance while it is charging,
charging will stop.
1 Plug the power cord into the
E
appliance socket
and the
power supply unit into the wall
socket.
D
– The charging display
out.
goes
7
7
The ambient temperature should
be between 5 °C and 40 °C.
When fully charged, the applian-
ce works for about 40 to 60
minutes.
This depends on the attachment
being used. It is not advisable to
charge the batteries after every
use, especially if you do not use
the appliance for the full 30
minutes.
Charge the batteries at your con-
venience only when they are
completely discharged.
This increases their service life.
Avoid charging every day.
7
ENGLISH
POWER SUPPLY __________________________
Using the charging unit
Mains operation
(with the power supply
unit)
Check that the voltage indicated on
the type plate of the power supply
unit corresponds to your local
power supply.
E
1 Plug the socket
of the appli-
ance into the charging unit.
2 Plug the power cord into the
socket on the charging unit.
3 Plug the power supply unit into
the wall socket.
The only way to disconnect the
appliance from the power supply is
to unplug the power supply unit.
1 Insert the power cord into the
E
socket
on the appliance.
2 Plug the power supply unit into
the wall socket.
Caution
7
When in the bathroom or next to
a water connection, you must only
use the appliance in battery mode;
never run it from the mains.
ENGLISH
8
OPERATION ______________________________
Cutting hair ...
... using the ceramic/stainless steel
A
cutting head
(width 38 mm).
1 If necessary, remove the attach-
3 Place a towel around the neck
and shoulders of the person
whose hair you are trimming.
ment by pressing in both side
B
catches
and lifting off.
4 Make sure the person is seated
so that their head is roughly at
your eye level. Before trimming,
comb the hair so that it falls nat-
urally and you can see the direc-
tion in which it grows.
C
5 Press the
button to switch on
the appliance.
6 Begin use.
C
7 Press the
button to switch off
the appliance after use.
2 Insert ceramic/stainless steel
A
cutting head
carefully at the
top and press down until it clicks
into place.
ENGLISH
9
OPERATION ______________________________
Beard trimming ...
Trimming hair or beards
to a certain length ...
... using the beard trimming attach-
9
ment
(width 30 mm).
1
... using the comb attachments
6
to
.
Comb #1
Comb #2
Comb #3
Comb #4
Comb #5
Comb #6
Comb #7*
2 mm
4 mm
8 mm
12 mm
16 mm
20 mm
1 If necessary, remove the attach-
ment by pressing in both side
B
catches
and lifting off.
* is designed for thinning out hair.
2 Insert beard trimming
9
attachment
carefully at the
1 If necessary, remove the attach-
top and press down until it clicks
into place.
ment by pressing in both side
B
catches
and lifting off.
3 Loosen the beard hair by
combing the beard in the
direction the hair grows.
A
2 Insert attachment
(width
8
38 mm) or
(width 30 mm)
carefully at the top and press
down until it clicks into place.
C
4 Press the
button to switch on
the appliance.
5 Begin use.
C
6 Press the
button to switch off
the appliance after use.
ENGLISH
10
OPERATION ______________________________
Note
Thinning out hair ...
... using the comb attachment
(thinning to a length of 2 mm).
7
The comb attachments fit both
7
cutting heads.
3 Push the comb attachment care-
fully and firmly onto the rounded
rear half of the cutting head
from above and let it click into
place.
1 If necessary, remove the attach-
ment by pressing in both side
B
catches
and lifting off.
A
2 Insert attachment
(width
(width 30 mm)
8
38 mm) or
C
4 Press the
button to switch on
carefully at the top and press
down until it clicks into place.
the appliance.
5 Begin use.
7
3 Push the comb attachment
C
6 Press the
button to switch off
carefully and firmly onto the
rounded rear half of the cutting
head from above and let it click
into place.
the appliance after use.
7 After use, remove the comb
1
6
attachment
to
by
pressing the locking tab at the
back and removing the comb
attachment.
C
4 Press the
button to switch on
the appliance.
5 Begin use.
C
6 Press the
button to switch off
the appliance after use.
7 After use, remove the comb
7
attachment
by pressing the
locking tab at the back and
removing the attachment.
ENGLISH
11
OPERATION ______________________________
Note
Close shaving ...
... using the shaving attachment
7
You can remove the single blade
8
.
foil of the shaving attachment.
To do this, press both side catches
on the shaving attachment. Clean
the blade head with the cleaning
brush supplied.
1 If necessary, remove the attach-
ment by pressing in both side
B
catches
and lifting off.
8
2 Insert shaving attachment
carefully at the top and press
down until it clicks into place.
C
3 Press the
button to switch on
the appliance.
4 Begin use.
C
5 Press the
button to switch off
the appliance after use.
Note
7
Do not apply strong pressure
when shaving, as this could
damage the single blade foil.
ENGLISH
12
CLEANING AND CARE____________________
Caution
Cleaning and care
7
Never put the appliance,
7
Switch off the appliance and
charging unit or power supply
unit in water or any other liquid.
unplug the power supply unit
from the mains.
7
Before using the appliance again,
7
Remove the attachment and clean
ensure that all attachments have
been carefully dried using a soft
the blade head with the brush
supplied.
towel.
Caution
7
Do not use cleaning agents.
7
If cleaning with the brush is not
Note
sufficient, you can also rinse the
attachment under running water.
However, only do this once the
7
Remove any clippings after each
use.
attachment has been removed.
7
The cutting head on the
attachment does not normally
need to be oiled. If you clean the
attachment under running water
regularly but you also want to
maintain the original condition of
the cutting head for as long as
possible, it is worth oiling it at
regular intervals with the oil
provided.
7
Use a soft, dry cloth or the brush
supplied to clean the appliance
housing and the charging unit.
ENGLISH
13
CLEANING AND CARE_____________________
Storage
Environmental note
If you do not want to use the appli-
ance for a long period of time,
please store it carefully.
This product has been made from
high-quality parts and materials
which can be re-used and recycled.
1 Make sure it is unplugged, has
completely cooled down and all
the accessories are completely
dry.
Therefore, do not dispose of the
product along with normal house-
hold waste at the end of its service
life. Take it to a collection point for
the recycling of electrical and elec-
tronic equipment. This is indicated
by this symbol on the product, in
the operating manual and on the
packaging.
2 Store the parts in the original
box in a cool, dry place.
3 Make sure the appliance is kept
out of reach of children.
Please find out about collection
points operated by your local
authority.
Help protect the environment by
recycling used products.
ENGLISH
14
INFORMATION ___________________________
Technical data
This product fulfils the
European directives
2004/108/EC,
2006/95/EC and 2009/125/EC.
Power supply
Batteries: Nickel metal hydride
Mains adapter:
100 – 240 V , 50/60 Hz
˜
3.4 V DC 1000 mA
Ni-MH
Technical and design modifications are reserved.
ENGLISH
15
|