Model H8093
21⁄2 Ton Low Profile
Garage Jack
Operation
To raise the jack, rotate the pump valve knob
clockwise completely, then move the pump han-
dle or foot pump up and down. To lower the jack,
slowly rotate the pump valve knob counterclock-
wise.
Failure to follow these instructions could
result in serious personal injury or death:
1. DO NOT overload this jack beyond its
rated capacity. Overloading can cause
the jack to collapse and drop the load.
2. ALWAYS support the vehicle withappro-
priately rated support stands before
working under it.
3. DO NOT attempt to move the vehicle
while the jack is in use.
4. Use only on hard level surfaces like
concrete or asphalt. Other surfaces are
potentially unstable.
5. Center the load on the jack to maintain
proper balance and stability.
Pump Valve
Knob
Foot
Pump
Pump
Handle
6. DO NOT use jack if it begins leaking
fluid or if it sinks when placed under
load. These are indications that the jack
needs to be immediately serviced.
Specifications
Maximum Lifting Capacity ................... 5000 Lbs.
Lifting Range ......................................33⁄8"–151⁄16"
Weight ................................................... 108 Lbs.
Figure 1. Jack controls.
If you need help with the Model H8093, call our
Technical Support line at: (570) 546-9663.
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR8824 PRINTED IN CHINA
H8093 Parts Breakdown and List
��
��
��
��
��
��
��
�
�
�
�
�
�
�
�
�
��
��
��
��
��
��
��
��
���������
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
�
��
��
��
��
��
��
�
��
��
�� �� ��
��
��
REF PART #
DESCRIPTION
COVER
REF PART #
PH8093027
DESCRIPTION
SUPPORT ROD
1
PH8093001
PN09M
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
2
HEX NUT M12-1.75
PH8093028
PH8093029
PH8093030
PH8093031
PS14M
TORSION SPRING
EXTENSION SPRING
PUMP ASSEMBLY
FOOT PEDAL
3
PH8093003
PH8093004
PH8093005
PH8093006
PH8093007
PH8093008
PH8093009
PH8093010
PH8093011
PH8093012
PR06M
FENDER WASHER 12MM
FRONT WHEEL SLEEVE
FRONT WHEEL
4
5
6
LEFT FRAME
PHLP HD SCR M6-1 X 12
PEDAL BASE
7
RUBBER PAD
PH8093033
PH8093034
PH8093035
PH8093036
PH8093037
PB35M
8
SADDLE
IDLER WHEEL
9
LIFTING ARM ASSEMBLY
FRONT WHEEL AXIS
CONNECTING ROD AXIS
LONG CONNECTING ROD
IDLER WHEEL SHAFT
TORSION SPRING
HANDLE SOCKET
HEX BOLT M12-1.75 X 40
FLAT WASHER 12MM
OPERATION HEAD
OPERATION ROD 2
COTTER PIN 4 X 26MM
COTTER PIN 3 X 16MM
OPERATION ROD 1
COTTER PIN 3 X 28MM
PUMP VALVE KNOB
LOWER HANDLE
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
EXT RETAINING RING 16MM
RIGHT FRAME
PW06M
PH8093014
PH8093015
PLW06M
PH8093040
PH8093041
PH8093042
PH8093043
PH8093044
PH8093045
PH8093046
PH8093047
PS03M
CONNECTING ROD
LOCK WASHER 10MM
HEX NUT M10-1.5
PN02M
PS26M
PHLP HD SCR M6-1 X 20
AXIS FOR PUMP
PH8093019
PB20M
HEX BOLT M8-1.25 X 35
EXT RETAINING RING 25MM
LOCK WASHER 12MM
LOCK WASHER 18MM
CONNECTING BOLT
PR11M
PLW05M
PHLP HD SCR M6-1 X 8
UPPER HANDLE
PLW12M
PH8093049
PH8093050
PH8093051
PH8093024
PH8093025
PS29M
MACHINE ID LABEL
FILL PLUG
REAR CASTER ASSEMBLY
PHLP HD SCR M12-1.75 X 25
The machine ID label warns about hazards and ways to prevent injury. The owner of the jack
MUST maintain the original location and readability of the label. If the label is removed or becomes
�����������������������������������������������������������������������
�������������������������������������
������������������������������������
�����������������
��������������������������������
���������������������������������
����
�����������������
����
������������������
|