UNVENTED (VENT-FREE) UNIVERSAL FIREBOX
OWNER’S OPERATION AND INSTALLATION MANUAL
PFS
®
CIRCULATINg MODELS
CgFB32CC
WARNING: If the information in this manual is not
followed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
FoR use oNlyWIthAlIsted GAs-FIRed uNveNted
decoRAtIve Room heAteR Not to exceed 40,000
Btu/Hr. Do not BuilD a wooD fire.
Carefully review the instructions supplied with the
decorative type unvented room heater for the minimum
fireplace size requirement.
do Not INstAll AN ApplIANce IN thIs FIRebox
uNless thIs FIRebox meets the mINImum dImeN-
sions requireD for tHe installation.
this firebox has been tested and approved under ansi
Z21.91 for use with any ansi Z21.11.2 approved gas logs.
installer: leave this manual with the appliance.
ConsuMer: retain this manual for future reference.
SAFETy
Continued
1. Do not use this firebox as a wood-burning
fireboxfrontandscreenbecome
very hot when running heater.
Keep children and adults away
from hot surface to avoid burns
or clothing ignition. firebox
will remain hot for a time after
shutdown.allowsurfacetocool
before touching.
fireplace. Use only decorative unvented
room heaters (log sets).
2. Do not add extra logs or ornaments such
as pine cones, vermiculite or rock wool.
Using these added items can cause
sooting.
3. Use only the provided hood or appropri-
ate hood accessory. See Accessories on
page 17.
4. Vent-free gas log heaters installed in these
fireboxes require fresh air ventilation to
run properly. See Air for Combustion and
Ventilation, page 6.
Carefully supervise young chil-
dren when they are in the room
with firebox.
5. Do not run firebox
• where flammable liquids or vapors are
used or stored
• under dusty conditions
You must operate this fireplace
with the provided fireplace
screen, hood if provided, in
place. Make sure these parts
are in place and screens are
closed before running firebox.
the supplied hood may not be
replacedwithahoodwhichmay
be provided with a log heater.
6. Do not use this firebox to cook food or
burn paper or other objects.
7. Turn firebox off and let cool before servic-
ing. Only a qualified service person should
service and repair firebox.
8. Operating firebox above elevations of
4,500 feet could cause pilot outage.
9. Do not use the firebox if it has been un-
der water due to the shock hazard that
could result with the blower accessary (if
installed) in place.
Keepthefireplaceareaclearand
freefromcombustiblematerials,
gasoline and other flammable
vapors and liquids.
LOCAL CODES
Install and use heater with care. Follow all
local codes. In the absence of local codes,
use the latest edition of The National Fuel Gas
Code, ANSI Z223.1/NFPA 54*. Firebox must
be electrically grounded in accordance with
the National Electrical Code, ANSI/NFPA70
(latest edition).
state of massachusetts: The installation
must be made by a licensed plumber or
gas fitter in the Commonwealth of Mas-
sachusetts.
Sellers of unvented propane or natural
gas-fired supplemental room heaters shall
provide to each purchaser a copy of 527
CMR 30 upon sale of the unit.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
Vent-free gas products are prohibited for
bedroom and bathroom installation in the
Commonwealth of Massachusetts.
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
124970-01A
3
PRODUCT FEATURES
opeRAtIoN
ReFRActoRy bRIck lINeR
This firebox is designed for use with approved Your firebox may feature a concrete refrac-
ANSI Z21.11.2 decorative type unvented room tory brick liner. As with all concrete liners,
heaters. (Physical size limitations apply. Refer this liner may develop slight cracks when
to minimum firebox requirements supplied exposed to heat. These cracks will not affect
with log heater.) It requires no outside vent- the performance of the fireplace or vent-free
ing or chimney making installation easy and gas logs.
inexpensive. When used without the blower,
the firebox requires no electricity making it
ideal for emergency backup heat.
bloWeR AccessoRy
The circulating models will accept either a ro-
tary type fan (model BK) or the triple radial fan
blower system (model BK3) accessories. The
blower circulates heated air from the firebox
into the room. Use of blower is optional.
LOCATINg FIREBOX
3. These models CANNOT be installed in a
bedroom unless the maximum BTU rating
of the installed vent-free log set is less
than 10,000 Btu/Hr.
plANNING
Plan where you will install the firebox. This will
save time and money later when you install
the firebox. Before installation, consider the
following:
4. Proper air for combustion and ventilation
(page 6).
1. Where the firebox will be located.Allow for
wall and ceiling clearances (see Installa-
tion Clearances, page 9).
2. Everything needed to complete installation.
4
124970-01A
PRODUCT SPECIFICATIONS
32" models
Left Side View
with Air Kit
Outside Air
Kit Location
(Optional)
221/2"
4"
8 1/8"
Firebox Top View
10 1/2"
8 1/8"
29/16
"
5/8"
37/16
"
251/8"
291/2"
815
/
16
"
347/16"
19 1/2"
16 11
363/8"
/
"
16
2 13
/
16
"
12 1/4"
Standoffs
41/4"
8 5/8"
361/2"
31/2"
321/4"
Built-In
Side
Nailing
Flanges
187/16"
163/4"
1415
/
16
"
291/2"
19/16
"
Square
Gas Line
Access
Holes
33/8"
65/16
81/8"
29/16
21/4"
"
"
6"
"
Electrical
Access Hole
815
/
16
Front View
93/4"
Right Side View
Figure 1 - Firebox Dimensions (32" Models)
124970-01A
5
AIR FOR COMBUSTION AND VENTILATION
unusually tight Construction
WARNING: this heater shall
not be installed in a room or
space unless the required vol-
ume of indoor combustion air
is provided by the method de-
scribed in the National Fuel Gas
Code,ANSI Z223.1/NFPA54, the
International Fuel Gas Code, or
applicablelocalcodes.readthe
following instructions to insure
proper fresh air for this and
other fuel-burning appliances
in your home.
The air that leaks around doors and windows
may provide enough fresh air for combustion
and ventilation. However, in buildings of un-
usually tight construction, you must provide
additional fresh air.
unusually tight construction is defined as
construction where:
a. walls and ceilings exposed to the out-
side atmosphere have a continuous
water vapor retarder with a rating of
one perm (6 x 10-11 kg per pa-sec-m2) or
less with openings gasketed or sealed
and
b. weather stripping has been added on
openable windows and doors and
Today’s homes are built more energy efficient c. caulking or sealants are applied to
than ever. New materials, increased insulation
and new construction methods help reduce
heat loss in homes. Home owners weather
strip and caulk around windows and doors
to keep the cold air out and the warm air in.
During heating months, home owners want
their homes as airtight as possible.
areas such as joints around window
and door frames, between sole plates
and floors, between wall-ceiling joints,
between wall panels, at penetrations
for plumbing, electrical and gas lines
and at other openings.
If your home meets all of the three criteria
While it is good to make your home energy above, you must provide additional fresh
efficient, your home needs to breathe. Fresh air. see Ventilation Air From Outdoors,
air must enter your home. All fuel-burning ap- page 8.
pliances need fresh air for proper combustion
and ventilation.
If your home does not meet all of the three
criteria above, proceed to Determining
Exhaust fans, fireboxes, clothes dryers and Fresh-Air Flow for Firebox Location,
fuel burning appliances draw air from the page 7.
house to operate. You must provide adequate
Confined and unconfined space
fresh air for these appliances. This will insure
The National Fuel Gas Code, ANSI Z223.1/
proper venting of vented fuel-burning appli-
NFPA54 defines a confined space as a space
ances.
whose volume is less than 50 cubic feet per
1,000 Btu per hour (4.8 m3 per kw) of the ag-
pRovIdING AdeQuAte
veNtIlAtIoN
The following are excerpts from National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Air for
gregate input rating of all appliances installed
in that space and an unconfined space as a
space whose volume is not less than 50 cubic
feet per 1,000 Btu per hour (4.8 m3 per kw)
Combustion and Ventilation.
of the aggregate input rating of all appliances
All spaces in homes fall into one of the three
installed in that space. Rooms communicating
following ventilation classifications:
directly with the space in which the appliances
1. Unusually Tight Construction
2. Unconfined Space
are installed*, through openings not furnished
with doors, are considered a part of the un-
confined space.
3. Confined Space
* Adjoining rooms are communicating only if
there are doorless passageways or ventilation
grills between them.
The information on page 6 through 8 will help
you classify your space and provide adequate
ventilation.
6
124970-01A
AIR FOR COMBUSTION AND VENTILATION
Continued
4. Compare the maximum Btu/Hr the space
can support with the actual amount of Btu/
Hr used.
deteRmINING FResh-AIR FloW
FoR heAteR locAtIoN
Determining if You Have a Confined or
unconfined space
Use this work sheet to determine if you have
a confined or unconfined space.
_________Btu/Hr (maximum the space
can support)
_________Btu/Hr (actual amount of
Btu/Hr used)
space: Includes the room in which you will
install heater plus any adjoining rooms with
doorless passageways or ventilation grills
between the rooms.
Example: 63,360 Btu/Hr (maximum the
space can support)
79,000 Btu/Hr (actual amount
of Btu/Hr used)
1. Determine the volume of the space (length
The space in the above example is a confined
space because the actual Btu/Hr used is more
than the maximum Btu/Hr the space can sup-
port. You must provide additional fresh air.
Your options are as follows:
x width x height).
Length x Width x Height = ______cu. ft.
(volume of space)
Example: Space size 22 ft. (length) x 18
ft. (width) x 8 ft. (ceiling height) = 3168 cu.
ft. (volume of space)
A. Rework worksheet, adding the space
of an adjoining room. If the extra space
provides an unconfined space, remove
door to adjoining room or add ventilation
grills between rooms. See Ventilation Air
From Inside Building, page 8.
If additional ventilation to adjoining room
is supplied with grills or openings, add the
volume of these rooms to the total volume
of the space.
2. Multiply the space volume by 20 to deter-
mine the maximum Btu/Hr the space can
support.
B. Vent room directly to the outdoors. See
Ventilation Air From Outdoors, page 8.
C. Install a lower Btu/Hr heater, if lower Btu/
Hr size makes room unconfined.
_____ (volume of space) x 20 = (Maxi-
mum Btu/Hr the space can support)
If the actual Btu/Hr used is less than the
maximum Btu/Hr the space can support, the
space is an unconfined space. You will need
no additional fresh air ventilation.
Example: 3168 cu. ft. (volume of space) x
20 = 63,360 (maximum Btu/Hr the space
can support)
3. Add the Btu/Hr of all fuel burning appli-
ances in the space.
WARNING:Iftheareainwhich
theheatermaybeoperateddoes
notmeettherequiredvolumefor
indoorcombustionair,combus-
tion and ventilation air shall be
provided by one of the methods
described in the National Fuel
GasCode,ANSIZ223.1/NFPA54,
theInternationalFuelGasCode,
or applicable local codes.
Vent-free heater
Gas water heater*
Gas furnace
_______ Btu/Hr
_______ Btu/Hr
_______ Btu/Hr
_______ Btu/Hr
_______ Btu/Hr
Vented gas heater
Gas fireplace logs
Other gas appliances* + ______ Btu/Hr
Total = ______ Btu/Hr
* Do not include direct-vent gas appli-
ances. Direct-vent draws combustion
air from the outdoors and vents to the
outdoors.
Example:
40,000
_________ Btu/Hr
39,000
+________ Btu/Hr
79,000
=________ Btu/Hr
Gas water heater
Vent-free heater
Total
124970-01A
7
AIR FOR COMBUSTION AND VENTILATION
Continued
ventilation Air From outdoors
veNtIlAtIoN AIR
Provide extra fresh air by using ventilation
grills or ducts. You must provide two perma-
nent openings: one within 12" of the ceiling
and one within 12" of the floor. Connect these
items directly to the outdoors or spaces open
to the outdoors. These spaces include attics
and crawl spaces. Follow the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, Air for
Combustion and Ventilation for required size
of ventilation grills or ducts.
Ventilation air from inside Building
This fresh air would come from an adjoining
unconfined space. When ventilating to an
adjoining unconfined space, you must provide
two permanent openings: one within 12" of the
ceiling and one within 12" of the floor on the
wall connecting the two spaces (see options
1 and 2, Figure 3). You can also remove door
into adjoining room (see option 3, Figure 2).
Follow the National Fuel Gas Code, ANSI
Z223.1/NFPA 54, Air for Combustion and
Ventilation for required size of ventilation
grills or ducts.
IMPORTANT: Do not provide openings for
inlet or outlet air into attic if attic has a thermo-
stat-controlled power vent. Heated air entering
the attic will activate the power vent.
12"
Ve ntilated
Outlet
Attic
Air
Ve ntilation
Ve ntilation Grills
Into Adjoining Room,
Option 2
Grills
Into Adjoining
Room,
Outlet
Air
Or
Remove
Door into
Adjoining
Room,
Option
3
Option 1
T o Attic
T o
Crawl
Space
Inlet
Air
12"
Ve ntilated
Inlet Air
Crawl Space
Figure 3 - Ventilation Air from Outdoors
Figure 2 - Ventilation Air from Inside
Building
INSTALLATION
Caution: log heaters
installed in this firebox create
warm air currents. these cur-
rentsmoveheattowallsurfaces
nexttofirebox.installingfirebox
next to vinyl or cloth wall cover-
ings or operating firebox where
impurities (such as, but not
limited to, tobacco smoke, aro-
matic candles, cleaning fluids,
oil or kerosene lamps, etc.) in
the air exist, may discolor walls
or cause odors.
warninG: a qualified ser-
vicepersonmustinstallfirebox.
follow all local codes.
WARNING: Never install the
firebox
• in a bedroom or bathroom*
• in a recreational vehicle
• wherecurtains,furniture,cloth-
ingorotherflammableobjects
arelessthan42"fromthefront,
top or sides of the firebox
• in high traffic areas
• in windy or drafty areas
* unless the installed log set is
rated at 10,000 btu/hr or less
in a bedroom or 6,000 Btu/Hr
or less in a bathroom.
8
124970-01A
INSTALLATION
Continued
IMPORTANT: Vent-free gas log heaters add optional cabinet mantels (see Accessories,
moisture to the air. Although this is beneficial, page 17) or as abuilt-inunit.Clearancesarethe
installing firebox in rooms without enough same for either installation method.
ventilation air may cause mildew to form from
too much moisture. See Air for Combustion
and Ventilation, page 6.
cAutIoN: do not install
the firebox directly on carpet
or vinyl.
IMPORTANT: Make sure firebox is level.
If firebox is not level, log set will not work
properly.
Note: Your firebox is designed to be used in
zero clearance installations. Wall or framing
material can be placed against any exterior
surface on the rear, sides, top or bottom of
your firebox, except where standoff spacers
are integrally attached. If standoff spacers are
attached to your firebox, these spacers can
be placed directly against wall or framing ma-
terials. Use the dimensions shown for rough
opening to create the easiest installation.
Example
*
*Minimum 16" from Side Wall
Use dimensions shown for rough openings
to create the easiest installation (see Built-In
Firebox Installation, page 10).
Figure 4 - Minimum Clearance for
Combustible to Wall
mantel clearances for built-In Installation
If placing custom mantel above built-in firebox,
you must meet the minimum allowable clear-
ance between mantel shelf and top of firebox
opening shown in Figure 5, page 10. These
are the minimum allowable mantel clearances
for a safe installation. Use larger clearances
wherever possible to minimize the heating of
objects and materials placed on the mantel.
INstAllAtIoN cleARANces
WARNING: maintain the
minimum clearances. if you can,
provide greater clearances from
floor, ceiling and adjoining wall.
Carefully follow these instructions. This will
ensure safe installation.
Minimum wall and Ceiling Clearances (see
figure 4)
A. Clearances from the side of fireplace
cabinet to any combustible material and
wall should follow diagram in Figure 4.
Example: The face of a mantel, bookshelf,
cAutIoN: do not allow the
vent-freegaslogheatertotouch
or extend beyond the fireplace
screen.
notiCe: surface temperatures
of adjacent walls and mantels
become hot during operation.
walls and mantels above the
firebox may become hot to
the touch. if installed properly,
these temperatures meet the
requirement of the national
product standard. follow all
minimum clearances shown in
this manual.
etc. is made of combustible material and
1
2
protrudes 3 / " from the wall. This com-
bustible material must be 4" from the side
of the fireplace cabinet (see Figure 4).
B. Clearances from the top of firebox opening
to ceiling should not be less than 42".
C. When firebox is installed on carpeting or
other combustible material, other than
wood flooring, firebox should be installed
on a metal or wood panel extending the
full width and depth of enclosure.
D. Clearances from bottom of firebox to the
floor is 0".
These fireboxes can be installed as freestand-
ing units against a wall with the approved,
124970-01A
9
INSTALLATION
Continued
table 1
NotIce:Ifyourinstallationdoes
rough opening Dimensions for
built-in Installation
Front Width
not meet the minimum clear-
ances shown, you must do one
of the following:
• raise the mantel to an accept-
able height
Depth
(Min.)
Model (Inside to Inside)
Height
36 / " 16 1/4"
7
3
8
4
32"
34 / "
• remove the mantel
buIlt-IN FIRebox INstAllAtIoN
Figure
6a
Depth
(Minimum)
Built-in installation of this firebox involves
installing firebox into a framed-in enclosure.
This makes the front of firebox flush with wall.
Optional brass trim accessories are available
(see Accessories, page 17). The brass trim
will extend past sides of firebox approximately
1/2". This will cover the rough edges of the
wall opening. If installing a mantel above the
firebox, you must follow the clearances shown
in Figure 6. Follow the instructions below to
install the firebox in this manner.
Height
Width
(Inside to Inside)
FOR 32" MODELS
0" CLEARANCE
Figure
6b
3
8
39 / "
3
4
27 / "
1. Frame in rough opening. The firebox fram-
ing should be constructed of 2 x 4 lumber
or heavier. Use dimensions in Table 1
and rough opening layout in Figure 6a.
Adjust framing so that firebox flushes
with finished wall surface. If installing in a
corner, use dimensions in Figures 6b for
rough opening.
1
1
1
2
*10 / "
2
*10 / "
2
34 / "
5
8
55 / "
* These dimensions allow for min. Clearances to
a 45° projected side wall. However, clearances
to projected mantel trims and facings are allowed
within a min. Of 16" to a perpenducular wall as
shown in Figure 4, on page 9.
2. Install gas piping to firebox location. See In-
stalling Gas Line, page 11 and Connecting
to Gas Supply in log set owner’s manual.
Wall board or facing
Figure 6 - Rough Opening for Installing
in Wall
Mantel Shelf
material (above
Note: Any portion of the
firebox) may be of
IMPORTANT: If installing blower accessory
(circulating models with louvers only), see
Hard-Wiring Firebox, page 15.
mantel shelf must NOT
extend beyond this profile.
combustible material,
including decorative
mantel ornaments or
other similar projec-
tions off of the facing
material.
12"
6 3
1 1
/
4"
/2"
3. Carefully set firebox in front of rough open-
ing with back of firebox inside wall open-
ing. IMPORTANT: If installing a perimeter
trim kit, see instructions included with
trim accessory. You must install shoulder
screws from trim kit now.
Framing
Material
Noncombustible
Material May
12" 16" 20"
Project Off this
Surface above
the Firebox Hood
Firebox
4. Carefully insert firebox into rough opening.
Note: All vertical
measurements are
from top of fireplace
hood opening to
bottom of mantel shelf.
These minimum
5. Attach firebox to wall studs using nails
or wood screws through holes in nailing
flange (see Figure 7 on page 11).
Wire-mesh
Screen
Supplied
Firebox Hood
Must Be Used
at All Times
clearances replace any
other recommended
clearances supplied
with your ANSI Z21.11.2
approved gas logs.
Figure 5 - Minimum Mantel Clearances
for Built-In Installation
10
124970-01A
INSTALLATION
Continued
6. If using an optional perimeter trim kit,
INstAllING FIRebox usING
install the trim after final finishing and/or
painting of wall. See instructions included
with trim accessory for attaching trim.
optIoNAl AccessoRy mANtels
warninG: a qualified ser-
vicepersonmustinstallfirebox.
follow all local codes.
7. Install and properly test gas log heater.
Follow installation instructions included
with the vent-free gas log heater that is
being installed.
This firebox may be installed using a cabinet
mantel accessory against a wall in your
home. The firebox and cabinet mantel can
be installed directly on the floor. A trim kit is
included with the mantel accessories. Follow
instructions with mantel for installation.
IMPORTANT: When finishing your firebox,
combustible materials such as wall board,
gypsum board, sheet rock, drywall, plywood,
etc. may be butted up next to the sides and top
of the firebox. Combustible materials should
never overlap the firebox front facing.
INstAllING GAs lINe
WARNING: do not allow any
combustiblematerialstooverlap
the firebox front facing.
notiCe:aqualifiedserviceper-
son must connect heater to gas
supply. follow all local codes.
IMPORTANT: Noncombustible materials such
as brick, tile, etc. may overlap the front facing,
but should never cover any necessary open-
ings like louvered slots.
IMPORTANT: See Connecting to Gas Supply
in your log set owner’s manual for details on
gas hookup.
You may run the gas line from either side of
the firebox (see Figure 8). Decide which side
you want to run the gas line from.
WARNING: do not allow
noncombustible materials to
cover any necessary openings
like louvered slots.
Note: This is one option for installing shutoff
valve. Check local codes for equipment shut-
off valve location requirements.
Equipment Shutoff
Valves (Install One)
WARNING: use only non-
combustible mortar or adhe-
siveswhenoverlappingthefront
facing with noncombustible
facing material.
Nails or Wood
Screws
Knockout
Locations
(Knock Out
One Hole)
Gas Line Hole
Figure 8 - Installing Gas Line and
Equipment Shutoff Valve (Model May
Vary From Illustration)
Nailing
Flanges
Figure 7 - Attaching Firebox to Wall Studs
124970-01A
11
INSTALLATION
Continued
Locate the recessed knockout in one of the
NotIce: if a log set is installed
in the firebox, disconnect log
set from gas supply and remove
from firebox. Contact a qualified
service person to do this.
There are two (2) blower accessory options for
use in the vent-free fireboxes. Blower acces-
sory models are BK and BK3. Model BK is a
rotary squirrel cage type blower with magnetic
attachment and variable speed control. The
BK3 is a triple fan blower system with an on/
off rocker switch.
firebrick sidewall liners (see Figure 8 on page
11 and Figure 9). Firmly tap the center of the
knockout with a chisel until it is released.
Carefully chisel the rough edges of the hole
you have made to smooth edges. This hole
will line up with the hole in the outer casing.
Locate the recessed knockout in one of the
firebrick sidewall liners (see Figure 8 on page
11 and Figure 9). Firmly tap the center of the
knockout with a chisel until it is released.
Carefully chisel the rough edges of the hole
to smooth edges. This hole will line up with
the hole in the outer casing.
The blower must be installed by removing the
lower face panel and placing blower into its
proper mounting position.
cAutIoN:donotuseexces-
sive force to remove the knock-
out.toomuchforcemaydamage
the firebrick concrete insert.
Decide which way you intend to gain access
into the bottom rear of the firebox to install
the blower accessory. The lower front panel
can be removed easily by snapping out the
front with a flat blade screwdriver. Use cau-
tion not to scratch any surfaces. Models with
louvered front panels can also be removed by
inserting fingertips between slots and gently
pulling out. DO NOT FORCE. The panels are
actually held in place by means of a retention
dimple embossed on the edge of removable
panels.
Firebrick Side Wall
Side
View
Remove
this Area
warninG:ifthereisaduplex
electrical outlet installed in the
right side of the bottom of the
fireplace base area (see figure
10), be sure that the electrical
power to the outlet is turned off
before proceeding with blower
installation. failure to do this
may result in serious injury.
Knockout
Chisel
Figure 9 - Location of Knockout for Gas
Line
INstAllING optIoNAl bloWeR
AccessoRIes
Duplex Electrical Outlet
NotIce: the firebox identifica-
tionlabel(includingmodelnum-
ber, serial number, clearances,
etc.) is located in the right side
screen pocket area on the front
of the firebox. see figure 19,
page 16.
Figure 10 - Accessing Duplex Electrical
Outlet Installed in Bottom Right Side of
Firebox
Note: Appearance of firebox may vary
depending on model.
12
124970-01A
INSTALLATION
Continued
model bk Installation
cure speed control to bracket with lock nut
by pushing and turning lock nut with pliers
clockwise until it is tight against bracket.
1. Attach the power cord to blower motor by
firmly pushing two female terminals at end
of power cord onto two spade terminals
on blower motor (see Figure 11).
7. Remove knockout plug from louver panel
by pressing top and bottom retaining
clips.
2. Attach green ground wire from power cord
to blower housing using screw provided
(see Figure 11). Tighten screws securely
with a phillips screwdriver.
8. Place louver panel, louvers pointing up,
backintoframedopening.Aligncontrolshaft
with rectangular opening by sliding control
bracketalongflange(seeFigure12onpage
14).
3. Place blower against lower rear wall of
firebox outer wrapper with exhaust port di-
rected upward. Depending on your model,
you may have to carefully route the blower
assembly past controls and brackets and
position blower inside back opening. The
blower will be held in position against the
back wall by magnets incorporated onto
blower housing (see Figure 11).
9. Fully seat louver panel into frame open-
ing by gently pressing along ends until
all dimpled retainers have snapped in
place.
10. Place control knob, provided, onto control
shaft (see Figure 12).
11. Check to make sure power cord is com-
pletely clear of blower wheel and there are
no foreign objects in blower wheel. Also,
double check all wire leads and make
sure wire routing is not pinched or in a
precarious position. Correct accordingly.
4. Be certain that all wire terminals are
securely attached to terminals on blower
motor and that the screw retaining the
green ground wire is tight.
5. Position speed control bracket over flange
on hearth pan by sliding it up between
firebox face and hearth pan flange, then
down until seated onto lower flange of lou-
ver opening (see Figure 12, page 14).
Caution:nevertouchblow-
er wheel while in operation.
6. Mount speed control box by placing plas-
tic control shaft through bottom hole on
speed control bracket. Top screw head
on control box will fit inside top hole on
bracket (see Figure 12 on page 14). Se-
Firebox Face
Screw
Head and
Hearth
Pan
Top Hole
Flange
on Bracket
Speed
Control
Bracket
Magnetic Strips
Spade
Exhaust
Terminals
Port
Lower
Flange
Green
Ground
Wire
Control
Knob
Screw
Lock Nut
Control
Shaft
Air Flow
Lower
Direction
Louver
Side View
Firebox Bottom
Blower
Installed
After
Figure 12 - Attaching Speed Control to
Firebox with Panel Louvers
Lower
Panel
Removed
Blower
Location
Magnets
Figure 11 - Blower Model BK
124970-01A
13
INSTALLATION
Continued
12. Turn on power to duplex outlet if previ- Screws
ously turned off per warning in column 2,
page 12.
13. Plug in blower power cord to duplex outlet
(see Figure 10, page 12).
14. Turn blower on and check for operation.
Turn blower off by turning knob fully coun-
terclockwise before continuing.
15. Peel off backing paper and stick supplied
wiring diagram decal on firebox bottom
approximately 12" in from of blower (see
Figure 13).
Leg
Stands
BK3 Blower
Figure 14 - Mounting BK3 Blower
16. Replace all panels and/or brick bottom
panel if previously removed.
4. Remove 2 connectors from ON/OFF
rocker switch located on wiring harness
(see Figure 15).
model bk3 Installation
1. Remove knockout plug from louver panel
by pressing top and bottom retaining
clips.
5. Insert rocker switch into lower lover panel
with switch lever pointing outward.
2. Place BK3 fan assembly between two leg
stands with fan blades pointing toward
rear of fireplace (see Figure 14).
6. Reconnect previously removed wire con-
nectors onto switch terminals.
7. Check to make sure power cord is com-
pletely clear of blower and that there are
no foreign objects in blower. Also, double
check all wire leads and make sure wire
routing is not pinched or in a precarious
position. Correct accordingly.
3. Using screws provided, fasten upper
flange of blower bracket to hearth pan and
end flanges to leg stands (see Figure 16,
page 15).
Note: The wire assembly must be ar-
ranged in front of and away from fan
blades to reach power receptacle plug.
8. Turn on power to duplex outlet if previ-
ously turned off per warning in column 1,
page 12.
Va riable
Fan Switch
(N.O.)
Fan Switch
1
Off
Black
On
2
Blue
Red
(BKT Model
Only)
Switch
Terminals
11 0/115
V . A.C.
Black
Green
White
Blower
Motor
ON/OFF
Rocker
Switch
Wire Harness
Connectors
Wiring Diagram
Decal 12" in
Front of Blower
Figure 15 - Connecting Rocker Switch
Figure 13 - Location of Wiring Diagram
Decal (Model May Vary From Illustration)
14
124970-01A
INSTALLATION
Continued
9. Plug in blower power cord to duplex outlet
(see Figure 10, page 12).
10. Using ON/OFF rocker switch to turn
blower on and check for operation. Turn
blower off before continuing.
Duplex Box/
Handy Box
11. Peel off backing paper and stick supplied
wiring diagram decal on firebox bottom
approximately 12" in from of blower (see
Figure 16).
Strain Relief
12. Replace all panels and/or brick bottom
panel if previously removed.
Figure 17 - Hard-Wiring Firebox
combustIoN AIR kIt model Ak4
(oPtional)
ON/OFF
110/115
Panel Switch
V. A.C.
Black
Hot
Blower
Motor
No. 1
Blower
Motor
No. 2
Blower
Motor
No. 3
The outside air kit may be installed on the
left side of the fireplace only. The vent can be
installed through any outside wall a minimum
of three feet below fireplace termination cap.
The handle to operate the damper door for the
outside air inlet will be located inside the left
“screen pocket” of the firebox (see Figure 18).
Pull the handle to open or push to close.
Nuetral
Black
Figure 16 - BK3 Wiring Diagram
hARd-WIRING FIRebox
notiCe: a qualified electrician
mustconnectelectricalwiringto
duplex outlet for built-in instal-
lation. follow all local codes. in
absence of local codes follow
TheNationalElectricCodeANSI/
NFPA 70.
cAutIoN:Air inlet ducts are
not to terminate in attic space.
Screen Pocket
The “Handy Box” with duplex outlet is pro-
vided in the firebox located in the lower right
base area.
Air Kit
Handle
1. Remove screw holding duplex outlet cover
to handy box. Remove duplex outlet.
2. Route electrical cable through strain relief
and handy box (see Figure 17).
3. Connect electrical cable to duplex outlet.
Match wire colors to those on duplex out-
let. Be sure to connect the ground wire.
4. Place duplex outlet back into handy box
and secure with screws. Replace outlet
cover.
Figure 18 - Air Kit Handle Location
124970-01A
15
INSTALLATION
Continued
Top View of Rod Layout
INstAllING FIReplAce hood
ANd scReeN
1. Attach hood to firebox using screws pro-
Rear Hole
vided (see Figure 19).
2. Insert each rod through all rings located
at top of screen.
Identification
Label Location
Front
Hole
3. Insert first rod into rear hole in left side
of firebox. Fasten rod to rear hole near
center of firebox using #10 x 3/8" Phillips
screw provided (see Figure 20).
Rod
Ring
4. Insert other rod into front hole on right
side of firebox and fasten using remaining
Phillips screw.
Screen
Hood
Screw
Figure 20 - Installing Fireplace Screen
(Model May Vary From Illustration)
Screws
Figure 19 - Screw and Hood Placement
(Model May Vary From Illustration)
REPLACEMENT PARTS
Note: Use only original replacement parts. When calling have ready:
This will protect your warranty coverage for
parts replaced under warranty.
• your name
• your address
If your new product is missing a part or has
a broken component, please do not return it
to the store. Call FMI PRODUCTS, LLC at
1-866-328-4537 to answer questions and
replace parts under warranty.
• model and serial numbers of your heater
• how heater was malfunctioning
• purchase date
TEChNICAL SERVICE
You may have further questions about instal- When calling please have your model and se-
lation, operation, or troubleshooting. If so, rial numbers of your heater ready.
contact FMI PRODUCTS, LLC at 1-866-328-
4537.
You can also visit FMI PRODUCTS, LLC’s
16
124970-01A
ACCESSORIES
Purchase these accessories from your local louveR tRIm
dealer. If they can not supply these accessories
For use with Rolled louvers only
call FMI PRODUCTS, LLC at 1-866-328-4537
for information. You can also write to the ad-
dress listed on the back page of this manual.
lt32b - 32" Brushed Brass
lt32p - 32" Platinum
fire CraCKle - Cf6-a
peRImeteR tRIm
Creates the sound of a real burning fire.
pt32b - 32" Brushed Brass
pt32p - 32" Platinum
bloWeR kIt
bk - Squirrel Cage Blower With Speed
Control
FAce/louveR pANel kIts
bk3 - Triple Fan Blower System
sp32 - 32" Smooth Faced Black
sl32 - 32" Stamped Louver Black
Rl32 - 32" Rolled Louver Black
Fp32 - 32" Filigree Panel Black
ReFRActoRy bRIck lINeR kIt
bl32s - Smooth White
Fp32b - 32" Filigree Panel Brushed Brass
Fp32p - 32"Filigree Panel Platinum
hoods
h32b - Brushed Brass
h32p - Platinum
mANtels
32" WAll mANtels
W32tu - 32" Unfinished, Traditional
W32to - 32" Oak Stain, Traditional
W32co - 32" Oak Stain, Classic
W32do - 32" Oak Stain, Dentil
W32Go - 32" Oak Stain, Georgian
32" coRNeR mANtels
c32tu - 32" Unfinished, Traditional
c32to - 32" Oak Stain, Traditional
c32co - 32" Oak Stain, Classic
c32Go - 32" Oak Stain, Georgian
124970-01A
17
PARTS
models cGFb32cc
22
21
20
23
18
19
17
16
28
15
29
10
25
26
9
7
5
24
27
4
11
14
3
12
8
6
13
2
1
18
124970-01A
PARTS
This list contains replaceable parts used in your firebox. When ordering parts, follow the
instructions listed under Replacement Parts on page 17 of this manual.
Part number
key
no. cGFb32cc descRIptIoN
qtY.
1
2
2
1
1
1
2
2
1
1
1
1
1
1
1
2
1
1
1
1
1
4
1
2
2
4
1
1
1
1
108441-01 Screen
2
108700-01 Screen Rod
3
11418
Push-On Nut
4
5
6
108414-01 Deflector Hood
108423-02 Face Top Panel
108423-05 Face Bottom Panel
7
8
**
**
Face Weldment
Firebox Support Leg
9
108434-02 Left Refractory Red
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
108430-02 Rear Refractory Red
108432-02 Right Refractory Red
108426-02 Bottom Rear Refractory Red
108428-02 Bottom Front Refractory Red
**
**
20027
**
Firebox Bottom
Firebox Surround
Refractory Retainer
Fireplace Top Insulation
Firebox Top
**
108415-01 Starter Pipe Collar
** Insulation Pan
108403-03 Fireplace Top
20280
**
Top Spacer
Fireplace Surround
110037-01 Junction Box
108654-01 Gas Conduit Left and Right Assembly
21171
14123
**
Gas Knock-Out Cover
Strain Relief
Air Kit Door Assembly
108425-01 Air Rod Retainer
pARts AvAIlAble Not shoWN
113140-01 Perimeter Trim Kit
1
** Not a field replaceable part.
124970-01A
19
WARRANTy
KEEP ThIS WARRANTy
Model (located on product or identification tag)_____________________________
Serial No. (located on product or identification tag)__________________________
Date Purchased __________________________
Keep receipt for warranty verification.
FMI PRODUCTS, LLC LIMITED WARRANTIES
New products
standard Warranty: FMI PRODUCTS, LLC warrants this new product and any parts thereof to be free
from defects in material and workmanship for a period of two (2) years from the date of first purchase from
an authorized dealer provided the product has been installed, maintained and operated in accordance with
FMI PRODUCTS, LLC’s warnings and instructions.
For products purchased for commercial, industrial or rental usage, this warranty is limited to 90 days from
the date of first purchase.
Factory Reconditioned products
limited Warranty: FMI PRODUCTS, LLC warrants factory reconditioned products and any parts thereof
to be free from defects in material and workmanship for 30 days from the date of first purchase from an
authorized dealer provided the product has been installed, maintained and operated in accordance with
FMI PRODUCTS, LLC’s warnings and instructions.
terms common to All Warranties
The following terms apply to all of the above warranties:
Always specify model number and serial number when contacting the manufacturer. To make a claim under
this warranty the bill of sale or other proof of purchase must be presented.
This warranty is extended only to the original retail purchaser when purchased from an authorized dealer,
and only when installed by a qualified installer in accordance with all local codes and instructions furnished
with this product.
This warranty covers the cost of part(s) required to restore this product to proper operating condition and
an allowance for labor when provided by a FMI PRODUCTS, LLC Authorized Service Center or a provider
approved by FMI PRODUCTS, LLC. Warranty parts must be obtained through authorized dealers of this
product and/or FMI PRODUCTS, LLC who will provide original factory replacement parts. Failure to use
original factory replacement parts voids this warranty.
Travel, handling, transportation, diagnostic, material, labor and incidental costs associated with warranty
repairs, unless expressly covered by this warranty, are not reimbursable under this warranty and are the
responsibility of the owner.
Excluded from this warranty are products or parts that fail or become damaged due to misuse, accidents,
improper installation, lack of proper maintenance, tampering, or alteration(s).
This is FMI PRODUCTS, LLC’s exclusive warranty, and to the full extent allowed by law; this express war-
ranty excludes any and all other warranties, express or implied, written or verbal and limits the duration of
any and all implied warranties, including warranties of merchantability and fitness for a particular purpose
to two (2) years on new products and 30 days on factory reconditioned products from the date of first
purchase. FMI PRODUCTS, LLC makes no other warranties regarding this product.
FMI PRODUCTS, LLC’s liability is limited to the purchase price of the product, and FMI PRODUCTS, LLC
shall not be liable for any other damages whatsoever under any circumstances including indirect, incidental,
or consequential damages.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For information about this warranty contact:
124970-01
Rev. A
2701 S. Harbor Blvd.
Santa Ana, CA 92704
07/09
1-866-328-4537
|