|
16-Port Fast Ethernet Switch
User’s Guide
M73-APO07-310
INTRODUCTION
The 16-Port Fast Ethernet 10/100Mbps N-Way Switch provides you a flexible, reliable, and
affordable solution of the Ethernet network. It comes with sixteen 10BASE-T /100BASE-TX
ports. The 16-Port Fast Ethernet 10/100Mbps N-Way Switch is able to operate in both half
and full-duplex modes. Each port delivers up to 200Mbps throughput in full duplex mode.
The 16-Port Fast Ethernet 10/100Mbps N-Way Switch also processes a N-Way auto-
negotiation function, which automatically adjusts the device for optimum operation; “Store-
and-Forward” architecture filters to eliminate error packets and improve efficiency. Plus, the
auto-MDI/MDIX technology provides the convenience of using a straight through or a
crossover Ethernet cable and you will be connected with any other devices. Moreover, the
built-in Universal Power Supply allows you to install the switch easily without the external
power adapter.
Key Features
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
ꢁ
Complies with IEEE 802.3 10Base-T and IEEE 802.3u 100Base-TX standards
“Store and Forward” architecture filters
IEEE 802.3x or Back Pressure (HDX) Flow Control
16 x RJ45 STP/UTP Ethernet ports on front panel
4K MAC Address table supported
10/100Mbps auto-detection on Full or Half Duplex
Each Ethernet port supports Auto-MDI/MDIX (auto-crossover) technology
Provides non-blocking and Head-of-line blocking forwarding prevention
256KB on-chip buffer
Built in Universal Power Supply: 90~264V
Emission certification: FCC Class B, CE mark
- 1 -
PARTS NAMES AND FUNCTIONS
Front Panel: LED Indicators
Status
LED
Color
Solid
Flashing
N/A
Power
LINK/ACT
Speed
Green Power is on.
Sending or Receiving
packets
Green Connection is detected
Green ON for 100Mbps, OFF for 10Mbps
N/A
Rear Panel: Power Port
- 2 -
HARDWARE INSTALLATION
The switch is considered as a “plug and play” network device and requires no special setup
procedures. Connect the power cord and cables correctly and you are ready to go.
Switch installation
1.
Put the switch on the appropriate location. When you install the switch, there are two
things needed to be considered:
ꢁLocation: Your switch should be located in a place that is central to your
home/office space and allows all computers and networked devices connected to
your switch.
ꢁPower: Remember to locate your switch near electrical outlet.
2.
3.
Power on the switch by connecting the power cord.
Verify if the power (POWER) LED is on. If the POWER LED does not light up,
check the power cord and power outlet to verify its connection. If it still remains unlit,
please contact your dealer for support.
Ethernet Port Connection
Connect user machines, servers, another switch, hub, or any other devices to the Ethernet
ports on this switch with either straight through or crossover Ethernet cables.
- 3 -
SPECIFICATION
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE802.3x Flow Control
Standards
Protocol
CSMA/CD
Ports
Sixteen 10/100Mbps RJ-45 ports support auto-MDI/MDIX
Store-and-Forward
Switching Scheme
Full Duplex: IEEE802.3x
Flow control
Cabling type
Half Duplex: Back Pressure
UTP Category 3 or better (10Base-T)
UTP Category 5 or better (100Base-TX)
10Mbps or 100Mbps (Half Duplex)
20Mbps or 200Mbps (Full Duplex)
4K
Speed per port
MAC Address
Power
Green
Power is up.
On for connection detected;
LINK/ACT
Green:
Flashing
receiving data
for
sending/
LED indicators
On for 100Mbps, off for
10Mbps
SPD
Green
Physical Dimension
Weight
273 x 161 x 45 ( mm) (Width x Depth x Height)
1.2 Kg
Input power specifications AC 90~264V
Power Consumption
Agency and Regulatory
Operating Temperature
Operating Humidity
13W
FCC Class B, CE mark
0°C to 40°C
5~90% non-condensing
- 4 -
|