Waves – Doubler
Software Audio Processor
User’s Guide
Waves Doubler software guide page 1 of 6
Chapter 2 – Controls and Displays.
The Doubler offers a selection of controls and displays as an interface to the
DSP algorithm. This chapter lists the different controls and displays and
details the properties of each.
CONTROLS
Per-Voice Control Strips
Each voice control strip offers the following controls:
ON/OFF: Default: On.
Turns the voice on or off.
GAIN: 0 to –48dBFS. Default: –12.
Sets the gain of the voice in relation to the other voices. The master gain can
further change the actual output gain of all voices.
PAN: –45 to +45 degrees. Default: V1 22.5, V2 –22.5, V3 45, V4 –45.
+45 degrees is fully right. –45 degrees is fully left. 0 is in the middle.
DELAY: 0 to 100 milliseconds. Default: 8ms.
Specifies the delay of the voice in relation to the direct signal. Note that the
lowest value possible depends on the settings of the Align Direct and Range
parameters. When the direct signal is aligned, the minimal delay possible at
any range is 0 because the direct signal is delayed to align with the natural
latency. When the Direct signal is real time, the minimal delay for range 80Hz
is 8ms and for 20Hz is 14ms.
FEEDBACK: 0 to 100 percent. Default: 0%.
Specifies the percentage of gain to be fed back to the input. Be careful when
setting values above 25%. These can lead to run-away feedback and loud
noises that can harm delicate equipment.
OCTAVER: On/Off. Default: off.
This switch shifts the voice 1 octave down along with all the other settings.
The button will light a downward arrow to indicate that the Octaver is On.
DETUNE: –100 to +100 cents.
100 cents equals a semitone. Use this control to set the voice’s detune in
relation to the source. Slight detunes of 2 to 12 cents tend to sound relatively
in tune while higher values begin to sound off and out of tune.
Waves Doubler software guide page 3 of 6
MODULATION DEPTH: –200 to +200 in cents. Default: 0.
Positive values will start by modulating upwards, negative values will start off
modulating downwards. The modulation will always occur around the voice’s
nominal detune so if you set a detune of 10 and a Mod Depth of 10, the voice
will begin by going upward 10 cents and then downward 20 cents, reaching
10 cents below the nominal detune.
MODULATION RATE: 0.1 to 200Hz. Default: 1Hz.
This value sets the voice’s pitch modulation rate. At 1Hz the modulation will
complete a full cycle in 1 second.
The Direct signal controls
ON/OFF: Default: On.
Turns the voice on or off.
GAIN: 0 to –48dBfs. Default: –12.
Sets the gain of the voice in relation to the other voices. The master gain can
further change the actual output gain of all voices.
PAN: –45 to +45 degrees. Default: V1 22.5, V2 –22.5, V3 45, V4 –45.
+45deg is fully right. –45deg is fully left. 0 is in the middle. In Stereo sources
the Pan for the direct will actually behave as a Rotation control for the whole
stereo image.
EQ Controls
The Doublers EQ section offers a Hi Shelf and Low Shelf filter. These filters
will affect the Doubler’s voices, but not the direct signal. The controls for the
filter are as follows:
ON/OFF: Default: On.
These turn the filter on and off allowing a quick A/B comparison to an EQ
setting in relation to no EQ. Double clicking on the Graph markers will also
turn the filter on and off.
GAIN: +12dB to –24dB
The Shelf can boost all that beyond its corner frequency by up to 12dB. It can
cut down much lower than that, down to -24dB, at which point the filter floor
drops to make a cut filter.
Waves Doubler software guide page 4 of 6
FREQUENCY: Low Shelf Cutoff 16Hz to 1600Hz. Default: 156Hz.
Hi Shelf 1000Hz to 21000Hz Default: 5990Hz.
Master controls include:
ALIGN DIRECT: On/Off. Default: Off.
When set to On, this control delays the direct signal in order to align it to the
Voices’ inherent latency. With the Align On, you can reach a relative delay of
0ms between the direct signal and the Voices. The Voices’ inherent latency
depends on the range: at 80Hz, the Voices’ inherent latency will be 7ms and
at 20Hz, it will be 24ms. When the Align direct is Off, the plug-in will not add
delay to the direct so it will be aligned with the Track’s original time, and the
minimum relative delay between the Voices and the direct is limited to the
Voices’ inherent delay.
HI PASS FEEDBACK: 16Hz to 12000Hz. Default: 16Hz.
Sets the Feedback’s Hi Pass filter cutoff frequency.
RANGE: 80Hz/20Hz Default: 20Hz.
Detuning lower frequencies requires higher inherent latency for the Voices.
The Range control specifies the lowest frequency that can be detuned with no
artifacts, and at the same time sets the lowest inherent latency for the voices.
Lower Range means higher latency.
If low latency is not a concern it is safer to work with the wider Range, down to
20Hz (latency is 24ms). When low latency is a concern, and the input signal
consists of frequencies above 80Hz (such as guitars and lead vocals), set the
Range to 80Hz, and the inherent latency will likewise be smaller. 20Hz Range
should be used for Doubling bass instruments and will perform more purely on
complex full range signals such as mixed sources.
MODULATION RESET.
Sometimes interesting sounds can be achieved by synchronized modulations,
but when you have to set the rate and depth individually, they will definitely go
out of sync. Click the Mod Reset to make them start together in perfect sync.
This control is also automateable and can be used to reset the modulators to
start at the exact position in selected cues of your session so they sound the
same each time.
Waves Doubler software guide page 5 of 6
Master Output and meters
MASTER OUTPUT GAIN: 0.0 to –infinity. Default: 0.0dB.
The Master Gain control will affect the total Doubler output, including the
direct path. When there is a generally good-sounding setup that occasionally
clips the output, you can adjust the gain in order to eliminate clipping.
OUTPUT METERS show the plug-in output and under the meters there are peak
counters. These counters will show the peak value until reset by clicking on
the meter or counter.
CLIP LIGHT lights in red whenever output clipping occurred. Lower the output
gain to avoid clipping. Click it to Reset.
Waves Doubler software guide page 6 of 6
|