Vision Fitness Elliptical Trainer X6150 User Manual

i t a l l  
s t a r t s  
w i t h a  
v i s i o n  
A s s e m b l y  
G u i d e  
500 South CP Avenue  
toll free 800.335.4348  
P.O. Box 280  
Lake Mills. WI 53551  
fax 920.648.3373  
phone 920.648.4090  
©2007 Vision Fitness. All Rights Reserved. 1.07  
AG18.51PRD  
REV1  
X6150 AND X6250HRT  
INCLINE ELLIPTICAL TRAINERS  
 
STEP  
3
PINK BAG  
A s s e m b l y  
G u i d e  
• Slide the console mast boot onto the  
console mast.  
STEP  
• Unwrap the wire harness located in  
the console mast frame bracket. Take  
the wire tie that exits the bottom of the  
console mast and wrap it around the  
end of the wire harness. Pull the wire tie  
up through the top of the console mast  
and slide the bottom of the console mast  
over the console mast frame bracket.  
2
Knuckle Joint  
Sleeve  
Pedal Footwell  
X6150 AND X6250HRT  
INCLINE ELLIPTICAL TRAINERS  
Knuckle Joint  
Cover  
• Insert a socket head bolt (M8x25L)  
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before  
proceeding, find your new Elliptical Trainers serial number located on the front axle tube, and enter here:  
with  
a
lock washer (M8) and  
a
flat  
washer (8x18x1.5T) to each of the four  
mounting holes on the sides of the  
console mast. Insert a socket head bolt  
(M8x25L) with a lock washer (M8) and  
an arc washer (8x18x1.5T) to the  
mounting hole on the backside of the  
console mast. When all bolts are in  
place tighten the bolts with the 6mm  
L-shaped wrench. Insert two sets screws  
(M8x10L) to the nuts welded in the front  
side of console mast and tighten them  
with a 4mm L -shaped wrench.  
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in  
your own records. Be sure to read your Owners Guide before using your new Elliptical Trainer.  
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12  
NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble your  
Elliptical Trainer to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts and  
screws are in place and partially threaded in before completely tightening any ONE bolt or screw.  
• Slide the console mast boot down  
in place over the frame covers.  
STEP  
1
2
ORANGE BAG  
• Remove the four mounting screws from  
the backside of the console. Plug the  
wire harness and heart rate wires into  
the back side of the console. Mount the  
console to the console mast with the four  
screws removed earlier in this step.  
STEP  
1
• Slide the right transport wheel into the  
front tube. Align the holes in the front  
tube with the screw holes in the transport  
wheel sleeve. Insert two screws  
(M4x15L). Tighten with the screwdriver.  
X6250 ONLY: Set the accessory tray  
on the console mast handlebars.  
Secure in place with four screws  
(M5x12L). Tighten with the screwdriver.  
X6150 ONLY: Remove the water  
bottle cage mounting screws from the  
console mast with the screwdriver.  
Mount the bottle cage to the mast with  
these same screws. Insert water bottle.  
• Repeat these steps on the left side.  
X6250HRT ONLY  
X6150  
STEP  
BLUE BAG  
• Slide the knuckle joint sleeve of the  
right pedal arm assembly onto the pin  
on the right side cover disk. Secure in  
Transport  
Wheel  
place with  
a
washer (8x25x1.5T)  
STEP  
4
GREEN BAG  
and bolt (M8x20L). Tighten with the  
5mm T-handle wrench.  
• Line up the holes in the right dual-  
action arm with the holes on the right  
rotation housing. Insert two bolts  
(M8x60L), with a lock washer (M8)  
and an arc washer (8x18x1.5T),  
through the holes in the center of the  
dual-action arm and thread into the  
rotation housing. Next, insert two fully  
threaded bolts (M8x45L), with a lock  
Console Mast  
• Slide the knuckle joint cover over  
the knuckle joint. Fix in place with a  
washer (5x10x1T) and a bolt (M5x10L).  
Tighten with the screwdriver.  
STEP  
3
• Attach a cover to the left and right  
side of the link arm connection joint.  
Fix each side in place with a washer  
Console Mast  
Boot  
(5x10x1T) and  
a
bolt (M5x10L).  
washer (M8) and  
a
flat washer  
Tighten with the screwdriver.  
(8x18x1.5T), through the flange on  
the side of the dual-action arm and  
into the rotation housing. Tighten all  
bolts with the 5mm T-handle wrench.  
Wire Harness  
Rotation Housing  
• Assemble the pedal footwell onto  
the right pedal arm with four flathead  
bolts (M5x12L). Tighten with the  
screwdriver.  
Dual-Action Arm  
• Position the rotation housing cap over  
the dual-action arm and snap in place.  
Rotation  
Housing Cap  
• Insert the footwell cushion into the  
footwell. Make sure all pegs are seated  
into their respective holes.  
Slide the axle sleeve through the  
socket joint on the right link arm. Slide  
a spacer ring onto each side of the  
axle sleeve.  
• Repeat these steps on the left side.  
STEP  
4
Console Mast  
Frame Bracket  
Slide the link arm axle sleeve  
Link Arm  
Axle Sleeve  
between the teeth on the bottom of the  
dual-action arm bracket. Insert a bolt  
(M8x45L) through the dual-action arm  
bracket and link arm axle sleeve. Fix  
in place with a washer (8x25x1.5T)  
and nut (M8). Tighten with the 13mm  
wrench and 5mm L-shaped wrench.  
• Attach a cover to the left and right  
side of the dual-action arm connection  
joint. Fix each side in place with the  
washer (5x10x1T) and bolt (M5x10L).  
Tighten with the screwdriver.  
• Repeat these steps on the left side.  
 

Tasco Camcorder 119422 User Manual
TDK Network Card VLCF Series VLCF4024 2 User Manual
Teac Fryer TC25 User Manual
Timex Heart Rate Monitor 229 095000 User Manual
Toshiba CRT Television 36HF71 User Manual
Toshiba Network Card DEV002Z 1 User Manual
Toshiba Personal Computer L640 User Manual
Tripp Lite Network Cables N105 010 GY User Manual
Tripp Lite Power Supply APS PV User Manual
VTech Cordless Telephone V311 User Manual