Speaker Placement
1 Center Speaker:
3 Rear Speaker:
NOTE:
Positioned on top or below the TV
set.
Positioned beside or slightly behind For effective SURROUND effect, rear
your favorite viewing position. The speakers need to be located beside
height should be a little above your or behind your listening position.
ear level.
2 Front Speaker:
Positioned on both sides of the TV
with equal distances away from the
TV.
Advanced Set Up:
4 Subwoofer:
For more details on speaker
placement, please refer to the
manual chapter “Positioning
Your Speaker”.
Can be positioned anywhere but
preferrably near a wall in the front.
For optimized performance, please follow the recommendations and illustration.
Center Speaker Support
Stand (Optional)
Q u i c k
Left Rear Speaker
(Surround)
1. Secure the support rod in
place using the screw and
washer provided as
THOMSON
3
Left Front Speaker
illustrated below.
46, quai Alphonse Le Gallo
92648 Boulogne
Cedex FRANCE
55987210 (EN)
Connect Guide
2
This guide will help you to set up your system
through several illustrations.
1
2. Move the TV support rod
up and down as illustrated
to adjust the height of the
stand. Tighten the screw
to fix the support rod in
place.
Center
2
4
3
Right Front Speaker
Right Rear Speaker
Subwoofer
(Surround)
DPL590HT
EN
DVD To Receiver
Speakers and FM Antenna
Audio Components
For details, please refer to
Speaker
NOTE:
Connection described below is also
applicable for any component having check the receiver and make sure it connect DVD to the receiver, follow
digital output (Cable, Satellite, MD, is set to the appropriate input. The steps 3 to 6 and select COAXIAL.
• After the connections are done,
• If a COAXIAL cable is used to
Follow the diagram to connect
Instruction manual chapter
“Connecting the Speakers”.
audio components.
• Match the speaker wire color
• The color of the wire should be
CDRW recorder, TV)
input being used will be displayed
after the source name. (DVD/OPT
means DVD uses Optical Input)
• To change input connection, follow
step 3 to 6 as described below.
to the speaker / receiver terminals the same as that on the terminals.
VCR
as shown on the illustration.
• Match the speaker to the
correct terminal on the receiver
(example: left speaker to left
speaker terminal on receiver)
• Connect the striped color wire
to the “-” terminal (both speaker
and receiver)
TV Connections
NOTE:
TVs with RF input may need a RF
modulator (not included) for
inputting audio signals.
• By default, DVD is set to use
Analog.
R
L
TV
Follow the diagram to connect
your DVD player to receiver.
Follow the illustration and
instructions provided to
hook up your speakers.
Connect components capable of outputing digital signals like Dolby Digital
(e.g. DVD player or Satelite/Cable Box) or standard PCM format digital signals
(CD player). Read section on “Input Signal Setting” under “Advanced Sound
Control” carefully to adjust the matching input settings.
SPEAKER
HOOK-UP
ANTENNA HOOK-UP
to AUDIO OUT (VCR)
RF cable
to AUDIO OUT (TV)
RF in
RF out
AU
3
DVD
1 Connect either the COAXIAL
or OPTICAL cable (not included).
2 Connect the Audio cable.
RF modulator
(if available)
OPTICAL
OUT
COAXIAL
OUT
R
L
5
AUDIO
OUT
6
4
Audio in
IN
TV
3 Select DVD
VCR
4 Press SETUP on the remote control.
5 Press the Left or Right adjustment
buttons to select Digital Input setup.
6 Press the Up or Down adjustment
buttons to select the input being
used (analog, coaxial, or optical)
and release to validate.
Audio cable
Audio out
to AUDIO OUT (DVD)
Antenna and Speaker
Wire Connection
AUDIO INPUT
2
1
The diagram shown above may varies from your actual RF
modulator, please refer to your RF modulator manual.
L
R
IN
COAXIAL OPTICAL
DIGITAL AUDIO
DVD
SAT
TV
CD
VCR
TAPE
NOTE: To receive Digital signal
(Dolby Digital) either a coaxial or
optical cable must be connected;
and in step 6, you have to select
coaxial or optical input
Push terminal tab down to
insert wire.
COAXIAL OPTICAL
DIGITAL AUDIO
Cables
DVD
To help you identify the cables used in audio, illustrations are provided below for your easy reference.
Audio cable
Optical Cable (Digital)
Coaxial Cable
(75Ω / Digital)
accordingly.
Release tab to lock wire in
the terminal.
AUDIO INPUT
L
NOTE: Make sure the insulation
is completely removed from the
ends of the Antenna and
speaker wires at all connection
points.
R
IN
COAXIAL OPTICAL
DIGITAL AUDIO
DVD
SAT
TV
CD
VCR
TAPE
Not Included
Not Included
Not Included
|