TRENDnet Switch S800i User Manual

Quick Installation Guide  
TE100-S800i  
 
TE100-S810Fi  
1. Before You Start  
Package Content  
TE100-S800i/TE100-S810Fi  
AC power cord  
RS-232 cable  
Quick Installation Guide  
User’s Guide CD-ROM  
System Requirements  
1. Workstations with network cards  
2. TCP/IP protocol installed in all workstations  
3. A web browser such as Internet Explorer or Netscape Navigator  
4. RJ-45 Network Patch Cable to connect your workstations to the  
TE100-S800i/TE100-S810Fi  
(TE100-S800i)  
8-Port 10/100Mbps Layer 2 Managed Switch  
or  
(TEG-S810Fi)  
8-Port 100Base-FX Layer 2 Managed Switch with 100Base-FX Port  
Internet  
8-port 10/100Mbps  
Fast Ethernet Mini Switch  
(TE100-S8P)  
5-port 10/100Mbps  
Fast Ethernet Mini Switch  
(TE100-S5Pplus)  
8-port 10/100Mbps  
Fast Ethernet Mini Switch  
(TE100-S88Epl
Servers with 32-bit PCI  
Fast Ethernet Card  
(TE100-PCIWA)  
Servers with 32-bit PCI  
Fast Ethernet Card  
(TE100-PCIWA)  
Workstations with 32-bit PCI  
Fast Ethernet Card  
(TE100-PCIWA)  
Accounting  
Department  
Sales  
Department  
MIS  
Department  
100Mbps  
1
 
English  
2. How to Connect  
1. Connect the AC Power cord to the back of  
the TE100-S800i/TE100-S810Fi.  
2. Connect the network cable to the front of the  
switch and your PC.  
3. Verify that the PWR led displays a solid  
green light.  
2
 
English  
3. Using the Switch  
1. Go to Start ? Settings ?  
Control Panel.  
2. Double-Click the Network  
Connection Icon.  
3. Right-Click Local Area  
Connection, and select  
Properties.  
3
 
English  
4. Click the General tab, select  
Internet Protocol(TCP/IP), and  
click Properties. Change the IP  
address to 192.168.16.222 and  
click OK to apply the settings.  
5. Open your web browser, type  
Enter.  
6. User Name: root  
Password: root  
7. Select the appropriate option to  
configure the SNMP switch.  
Your installation is now complete.  
Note: For more detail on advanced features, please consult the User's Guide.  
4
 
English  
Troubleshooting  
Q1. How come I cannot see any light from any of my LED's?  
A1. Your TE100-S800i/TE100-S810Fi is not getting any power. Make  
sure that your surge protector or your outlet is getting power and make  
sure that the AC Power cord is properly connected to your  
TE100-S800i/TE100-S810Fi.  
Q2. I changed my IP settings to 192.168.16.222 to access the switch, but I  
still cannot get into the Web configuration page. What should I do?  
A2. Make sure there is no other network device using the same IP  
address. Afterwards, consult the User's Guide to access the switch  
through the Console Port. Once you reach the command line interface,  
perform a factory reset and try again.  
Q3. I performed a factory reset on the TE100-S800i/TE100-S810Fi, but I  
still cannot access the web configuration page. What should I do?  
A3. If you are configuring more than one TE100-S800i/TE100-S810Fi,  
then it is possible that you are experiencing IP conflict between these two  
switches. Please configure each switch one at a time, and make sure you  
assign a unique IP address to each switch.  
If you have any questions regarding the TE100-S800i/TE100-S810Fi, please  
contact TRENDnet Technical Support Department.  
5
 
Certifications  
This equipment has been tested and found to comply with FCC and CE Rules.  
Operation is subject to the following two conditions:  
(1) This device may not cause harmful interference.  
(2) This device must accept any interference received. Including interference that may  
cause undesired operation.  
Waste electrical and electronic products must not  
be disposed of with household waste. Please  
recycle where facilities exist. Check with you Local  
Authority or Retailer for recycling advice.  
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV  
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS  
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO  
OPERATE THE EQUIPMENT.  
ADVERTENCIA  
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de  
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al  
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador  
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria  
existente en el pais o zona de instalación.  
 
TRENDnet Technical Support  
.
US Canada  
Toll Free Telephone: 1(866) 845-3673  
24/7 Tech Support  
.
.
.
.
.
Europe (Germany France Italy Spain Switzerland UK)  
Toll Free Telephone: +00800 60 76 76 67  
English/Espanol - 24/7  
Francais/Deutsch - 11am-8pm, Monday - Friday MET  
Worldwide  
Telephone: +(31) (0) 20 504 05 35  
English/Espanol - 24/7  
Francais/Deutsch - 11am-8pm, Monday - Friday MET  
Product Warranty Registration  
Please take a moment to register your product online.  
20675 Manhattan Place  
Torrance, CA 90501  
USA  
 
Copyright ©2006. All Rights Reserved. TRENDnet.  

TC electronic SDN BHD Guitar NDY 1 User Manual
Toshiba Security Camera IK C41R2 User Manual
Toshiba Vacuum Cleaner H6A HLS User Manual
TP Link Dishwasher TL SG1008 User Manual
Tripp Lite Switch 0SU22082 User Manual
True Fitness Fitness Equipment TrueStretch User Manual
Tru Test Home Security System Electric Fence Security System User Manual
Viking InterWorks Network Card 650CT User Manual
VocoPro Music Mixer DA 2050K User Manual
Weber Gas Grill S 640 NG User Manual