TP Link Dishwasher TL SG1008 User Manual

TP-LINK TECHNOLOGIES CO.,LTD.  
ADDǖFI.3,Bldg.R1-B.High-Tech Industrial Park,Shenzhen Road.Shenzhen.China  
 
COPYRIGHT & TRADEMARKS  
Specifications are subject to change without notice.  
is a  
registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands  
and product names are trademarks or registered trademarks of their  
respective holders.  
No part of the specifications may be reproduced in any form or by any means  
or used to make any derivative such as translation, transformation, or  
adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.  
Copyright © 2007 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.  
FCC STATEMENT  
This equipment has been tested and found to comply with the limits for a Class  
A digital device, pursuant to part 15 of the FCC Rules. These limits are  
designed to pro-vide reasonable protection against harmful interference when  
the equipment is operated in a commercial environment. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed  
and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a  
residential area is likely to cause harmful interference in which case the user  
will be required to correct the interference at his own expense.  
CE Mark Warning  
This is a class A product. In a domestic environment, this product may cause  
 
radio interference, in which case the user may be required to take adequate  
measures.  
SAFETY NOTICES  
Cautions  
Do not use this product near water, for example, in a wet basement or near a  
swimming pool.  
Avoid using this product during an electrical storm. There may be a remote risk  
of electric shock from lightning.  
 
CONTENTS  
Package Contents ..................................................................1  
Chapter 1 Introduction of the Product..............................2  
1.1  
Overview of the Product...............................................................2  
1.2  
Features..........................................................................................2  
Chapter 2 Installation.........................................................4  
2.1  
2.2  
2.3  
Mounting the Switch on a Desk.......................................................4  
Mounting the Switch in a Rack........................................................4  
Power On........................................................................................5  
Chapter 3 Identifying External Components....................7  
3.1  
3.2  
Rear Panel......................................................................................7  
LED Indicators ................................................................................7  
Appendix A: Specifications ...................................................9  
Appendix B: Troubleshooting.............................................10  
 
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
Package Contents  
The following contents should be found in your box:  
¾
¾
¾
¾
¾
One Gigabit Ethernet Switch  
One power cord  
This User's Guide  
Rubber footpads for Desk-mount  
Rack-mount kit for installing the switch in a 19-inch rack  
Note: If any of the above contents is damaged or missing, please  
contact the retailer from whom you purchased the Gigabit Ethernet Switch for  
assistance.  
1
 
 
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
Chapter 1 Introduction of the Product  
This chapter describes the features of the Gigabit Ethernet Switch.  
1.1 Overview of the Product  
The Gigabit Ethernet Switch provides you with a high-performance, low-cost,  
easy-to-use, seamless and standard upgrade to boost your old network to  
1000Mbps. Increase the speed of your network server and backbone  
connections make Gigabit a reality. Power users in the home, office,  
workgroup or creative production environment can now move large,  
bandwidth-intensive files faster. Transfer graphics, CGI, CAD, or multimedia  
files and other applications that have to move large files across the network  
almost instantly.  
The Gigabit Ethernet Switch features a non-blocking switching architecture  
that forwards and filters packets at full wire-speed for maximum throughput. It  
is compatible with all 10,100, and 1000Mbps Ethernet devices because it is  
standard-based, it protects your existing network investments while providing  
you with a straightforward migration path to faster Gigabit speeds.  
The Gigabit Ethernet Switch is plug-and-play and no configuration is required.  
Auto MDI/MDI-X cable detection on all ports eliminate the need for crossover  
cable or Uplink port. Each port can be used as general ports or Uplink ports,  
and any port can be simply plugged into a server, a hub, a router or a switch,  
using the straight cable or crossover cable. Diagnostic LEDs which display link  
status and activity, allowing you to quickly detect and correct problems on the  
network.  
1.2 Features  
¾
Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab standards  
2
 
     
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
¾
¾
¾
¾
¾
8/16/24/48 10/100/1000Mbps Auto-Negotiation RJ45 ports  
supporting Auto- MDI/MDIX  
All ports Support full/half-duplex mode for 10/100Mbps and full  
duplex- mode for 1000Mbps  
Supports IEEE802.3x flow control for full-duplex mode and  
backpressure for half-duplex mode  
Non-blocking switching architecture that forwards and filters packets  
at full wire-speed for maximum throughput  
4K entry MAC address table of the TL-SG1008 and 8K entry MAC  
address table of the TL-SG1016, TL-SG1024 and TL-SG1048 with  
auto-learning and auto-aging  
¾
¾
LED indicators for monitoring power, link, speed and activity  
Store-and-Forward switching method  
3
 
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
Chapter 2  
Installation  
2.1 Mounting the Switch on a Desk  
Before placing the Switch on a desk, attach four rubber footpads to the flutes  
on the Switch bottom, then lay the Switch on the desktop, where can be able  
to withstand 5kg of weight.  
TL-SG1008, TL-SG1016, TL-SG1024 and TL-SG1048 are different in the  
number of LED indicators and RJ45 ports. All figures are of TL-SG1008 in this  
user's guide.  
Note  
¾
Make sure there is a grounded AC outlet within 1.5 meters, and working  
well.  
¾
¾
Make sure there is free space for radiating heat and air.  
Make sure not too place anything to heavy on top of the switch.  
2.2 Mounting the Switch in a Rack  
The dimension of the Gigabit Ethernet Switch is designed according to the  
standard 19” rack-mountable steel case of Electronic Industries Association.  
Turn off all the equipment connected to the Switch before mounting it in the  
rack, then rivet the two “L” brackets onto each side of the Switch, fasten it with  
screws in the rack.  
4
 
     
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
Figure 2-1 Rivet the “L” brackets onto the Switch  
Figure 2-2 Fasten the Switch in the rack  
2.3 Power On  
The Gigabit Ethernet Switch is powered by AC power supply. Powering on the  
Switch, it will automatically initialize and its LED indicators should respond as  
follows:  
1)  
All of the 10/100Mbps Link/Act and 1000Mbps Link/Act LED indicators of  
the TL-SG1008 will flash momentarily at first, flash sequence later and  
flash momentarily lastly, which represent a resetting of the system.  
All of the 10/100Mbps Link/Act and 1000Mbps Link/Act LED indicators of the  
5
 
 
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
TL-SG1016/TL-SG1024 /TL-SG1048 will flash momentarily for one second,  
which represent a resetting of the system.  
2)  
The Power indicator will light up all the time.  
If the LED indicators don’t respond as described above, please check the  
power supply and connection.  
6
 
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
Chapter 3 Identifying External Components  
This Chapter describes the front panel, rear panel and LED indicators of the  
Switch. TL-SG1008, TL-SG1016, TL-SG1024 and TL-SG1048 are different in  
the number of LED indicators and RJ45 ports.  
Figure 3-1 TL-SG1008 Switch Front Panel sketch  
3.1 Rear Panel  
The rear panel of the TL-SG1008 only features a power receptacle, which is  
an AC power receptacle. Connect the female of the power cord head here,  
and the male head to the AC power outlet.  
Figure 3-2 TL-SG1008 Switch Rear Panel sketch  
3.2 LED Indicators  
The LED indicators include Power, 1000Mbps Link/Act and 10/100Mbps  
Link/Act LED indicators, which are used for monitoring and pre-  
troubleshooting of the Switch. The following section shows the LED indicators  
for the switch along with an explanation of each indicator.  
7
 
     
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
Figure 3-3 TL-SG1008 Switch LEDs sketch  
Power LED: This indicator will light solid red when the Switch powers up. If the  
LED is not lit, please check the power supply and connection.  
1000Mbps Link/Act LED: This indicator will light solid green when the  
corresponding port is connected to a 1000Mbps device and will flash green  
when data is being transmitted or received on the working connection.  
10/100Mbps Link/Act LED: This indicator will light solid green when the  
corresponding port is connected to a 10/100Mbps device and will flash green  
when data is being transmitted or received on the working connection.  
8
 
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
Appendix A: Specifications  
General  
IEEE802.3 10Base-T  
Standards  
IEEE802.3u 100Base-TX  
IEEE802.3ab 1000Base-T  
Topology  
Protocol  
Star  
CSMA/CD  
Ethernet: 10Mbps (Half Duplex), 20Mbps (Full Duplex)  
Fast Ethernet: 100Mbps (Half Duplex), 200Mbps (Full  
Duplex)  
Data Transfer Rate  
Gigabit Ethernet: 2000Mbps (Full Duplex)  
10Base-T: UTP category 3, 4, 5 cable (maximum 100m)  
EIA/TIA-568 100Ù STP (maximum 100m)  
100Base-TX: UTP category 5, 5e cable (maximum 100m)  
EIA/TIA-568 100Ù STP (maximum 100m)  
1000Base-TX: UTP category 5, 5e or above (maximum 100m)  
EIA/TIA-568 100Ù STP (maximum 100m)  
8/16/24/48 10/100/1000Mbps Auto-Negotiation RJ45 ports  
Power, 1000Mbps Link/Act, 10/100Mbps Link/Act  
Store-and-Forward  
Network Media(Cable)  
Number of Ports  
LED indicators  
Transfer Method  
MAC Address Learning  
Automatically learning, automatically aging  
10Base-T: 14880pps/Port  
Frame Filter Rate  
100Base-Tx: 148800pps/Port  
1000Base-T: 1488000pps/Port  
10Base-T: 14880pps/Port  
Frame Forward Rate  
100Base-Tx: 148800pps/Port  
1000Base-T: 1488000pps/Port  
9
 
 
TL-SG1008/TL-SG1016/TL-SG1024/TL-SG1048 Gigabit Ethernet Switch User Guide  
Appendix B: Troubleshooting  
1. The Power LED is not lit  
¾
Make sure the AC power cord connected the Switch with power source  
properly.  
¾
Make sure the power source is ON.  
2.  
The Link/Act LED is not lit when a device is connected to the  
corresponding port  
¾
Make sure that the cable connectors are firmly plugged into the Switch  
and the device.  
¾
¾
Make sure the connected device is turned on and working well.  
The cable must be less than 100 meters long(328 feet).  
10  
 
 

Teac MP3 Player SR 100I User Manual
Toastmaster Coffeemaker MERB10B User Manual
Toshiba Computer Drive MK1255GSX User Manual
Transition Networks Network Card E TBT FRL 01 User Manual
Tricity Bendix Dishwasher BDW 55 User Manual
Tyco Thermometer FILAC User Manual
Uniden Scanner UBC144XLT User Manual
Varta Network Card V AVM651F User Manual
Verbatim Mouse 96990 User Manual
VXI Headphones USB 100 User Manual