Sony Tent BRCSDP16 User Manual

Installation and Operation Instructions for the following model:  
BRCSDP16  
OUTDOOR AND INDOOR DOME HOUSING  
CONTENT OF BOX:  
(1) Housing  
(1) Supplied Parts  
(1) Power Connector (Heater/blower)  
(1)Toolhead Driver  
(1) Operation Instruction Manual  
81-IN6584 03082011  
 
If you wish to provide a single power transformer it is  
recommended that:  
WIRING  
1. Be certain that you know the total power consumption of  
the housing Heater (25 watts) + Blower (1 watt) + camera  
pan/tilt (25 watts).  
WIRING INSTRUCTIONS (OUTSIDE OF HOUSING)  
BNC  
2. Check the supplied wiring chart (see below) to be sure that  
you have the proper gauge wire for the distance that you  
intend to run your power wires.  
(Large)  
Power  
3. Bring power to the 3 and 4 position of the power connector  
(yellow and green wire).  
(Small)  
Alarms  
4. Jumper from the 1stposition to the 3 rdposition and from  
the 2nd position to the 4th position of the terminal block.  
Be careful not to short between the yellow and green wires.  
Wiring Color Code Power and Control Inputs  
Green  
POWER  
Add 2 jumpers for  
single power input  
Yellow  
1
2
3
4
Camera Power (24 VAC)  
Camera Power (24 VAC)  
Red  
Wires from  
Dome  
Orange  
Heater and Blower Power (24 VAC) Yellow  
Heater and Blower Power (24 VAC) Green  
CONTROL  
1
2
3
4
Alarm 1  
Blue  
AC  
24V  
Power  
Supply  
Side  
Alarm 2  
Alarm 3  
Common  
Violet  
Gray  
White  
Orange  
Red  
WIRING INSTRUCTIONS (INSIDE OF HOUSING)  
1. The internal power supply provides 12Vdc power.  
NOTE: The total power consumption for the heater  
and blower, PLUS the camera you choose,  
need to be added together.  
2. Plug in right angle power plug to back of camera;  
plug provides 12Vdc to camera.  
In this example, a 60VA AC24V is required.  
24V AC Wiring Distances  
The following are the recommended maximum distances for 24 VAC  
with a 10% voltage drop (10% is generally the maximum allowable  
voltage drop for AC powered devices).  
Wire Gauge  
Total vA  
consumed  
20  
18  
16  
14  
12  
10  
-
22  
250  
120  
89  
400 600 960  
-
-
12DC  
5.5  
10  
20  
30  
40  
50  
60  
70  
80  
Make all connections  
to the camera.  
180 300 480 800 1300  
-
+
141 225 358 571 905 1440  
90 130 225 350 525 830  
70 112 179 285 452 720  
65  
OPTIONAL  
44  
1
2
3
4
Alarm 1  
Alarm 2  
Blue  
56  
47  
40  
34  
90  
75  
64  
55  
143 228 362 576  
119 190 301 480  
102 163 258 411  
35  
Violet  
Gray  
White  
29  
Alarm 3  
25  
Common  
85  
140 215 340  
31  
 
INSTALLING THE CAMERA  
1
Install the Sony BRC700 pan/tilt onto the quick release  
bracket using the (2) screws and washers provided with the  
camera (Figure 4).  
2
Place the Sony BRC700 pan/tilt and quick release bracket in  
the housing, sliding the three open screw slots over the screws  
in the housing. Slide the bracket back, then tighten the captive  
screw on the bracket (Figures 5 and 6).  
Figure 4  
Figure 5  
Figure 6  
 
IMPORTANT SAFEGUARDS  
SAFETY PRECAUTIONS  
1
2
3
Read Instructions - All the safety and operating instructions  
should be read before the unit is operated.  
CAUTION  
Retain Instructions - The safety and operating instructions  
should be retained for future reference.  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
!
Heed Warnings - All warnings on the unit and in the operat-  
ing instructions should be adhered to.  
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,  
DO NOT REMOVE COVER (OR BACK).  
4
5
6
Follow Instructions - All operating and user instructions  
should be followed.  
NO USER SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL  
Electrical Connections - Only a qualified electrician should  
make electrical connections..  
The lightning flash with an arrowhead symbol, within  
an equilateral triangle, is intended to alert the user to the  
presence of non-insulated “dangerous voltage” within the  
product’s enclosure that may be of sufficient magnitude to  
constitute a risk of electric shock to persons.  
Attachments - Do not use attachments not recommended by  
the product manufacturer as they may cause hazards.  
7
8
Cable Runs - All cable runs must be within permissible  
distance  
Mounting - This unit must be properly and securely  
mounted to a supporting structure capable of sustaining the  
weight of the unit. Accordingly:  
The exclamation point within an equilateral triangle is  
intended to alert the user to presence of important operating  
and maintenance (servicing) instructions in the literature  
accompanying the appliance.  
!
a. The installation should be made by a qualified installer.  
b. The installation should be in compliance with local  
codes.  
UNPACKING  
c. Care should be exercised to select suitable hardware to  
install the unit, taking into account both the composition  
of the mounting surface and the weight of the unit. Be  
sure to periodically examine the unit and the supporting  
structure to make sure that the integrity of the in stalla-  
tion is intact. Failure to comply with the foregoing  
could result in the unit separating from the support  
structure and falling, with resultant damages or injury to  
anyone or anything struck by the falling unit.  
Unpack carefully. Electronic components can be damaged if improperly  
handled or dropped. If an item appears to have been damaged in s-hip  
ment, replace it properly in its carton and notify the shipper.  
Be sure to save:  
1
The shipping carton and packaging material. They are the safest  
material in which to make future shipments of the equipment.  
2
These Installation and Operating Instructions.  
SERVICE  
If technical support or service is needed, contact Sony at the following  
number:  
TECHNICAL SUPPORT  
8:15AM to 7:30PM (Eastern Time)  
1-800-883-6817  
 
Note:  
Please note that to achieve the increased depth with the aspheric design for optimal camera lens to  
capsule orientation, the capsule is slightly angled around the highest section. This creates a ”line, visible to  
the naked eye, around the upper most section of the capsule. Thislineserves as the geometric center line  
used to insure proper camera placement. It is not typically seen by the camera. However, Sony RZ series  
PTZ cameras are able to tilt up above the horizon to 25°, this wide range of tilt motion at a wide angle view  
may cause this line to be captured in the image.  
Warranty  
For warranty information on this and other Sony Security Systems Products, please visit:  
 

Sharp CRT Television 32SF560 User Manual
Shure Microphone 27C687 User Manual
Smooth Fitness Elliptical Trainer CE 32E User Manual
Sony Computer Drive HDE1B User Manual
Sony Flat Panel Television 4 127 735 111 User Manual
Sony Home Security System SSC M183 M183CE M188CE SSC M383 M383CE M388CE User Manual
Sony Projector VPL VW200 User Manual
Speed Queen Washer Dryer CL8761 User Manual
StarDot Technologies Digital Camera net camera User Manual
Sterling Plumbing Indoor Furnishings C711FSER User Manual