BID SPECIFICATION
FOR
PRODUCTION CRT MONITORS
MODEL NUMBER
PVM-136
INSTRUCTIONS:
REMOVE THIS COVER PAGE AND ADD TO REQUESTS FOR QUOTATION AND
PROPOSALS. THE OBJECTIVE OF THIS BID SPECIFICATION IS TO ASSIST YOU IN
CLEARLY SPECIFYING THE SONY PRODUCT IDENTIFIED ABOVE, AND ENSURING
THAT THE BUYER IS WELL INFORMED OF THE HIGH STANDARD OF
PERFORMANCE THAT IS TO BE EXPECTED OF A SONY PRODUCT. THE
INFORMATION IN THIS DOCUMENT IS CURRENT AS OF JUNE 2002. PRODUCT
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
SONY ELECTRONICS INC.
DISPLAY PRODUCTS GROUP
1 SONY DRIVE, MD S3D9
PARK RIDGE, NJ 07656
TEL# (201)-930-1000, FAX# (201)-358-4303
4.0 User Interface / Controllability Information
Control of this device shall be accomplished through the use of front panel
controls that display on on-screen menus, available in a minimum of 5
languages. A status menu shall display current device settings.
The following device functions shall be available for control:
Power On / off
Input Select
Brightness / Contrast
Video Decoder Functions
Audio Volume
Overscan / Underscan
H/V Delay
4:3 / 16:9 Aspect Ratio
Recall of the last video decoder function used shall be accomplished by touching
any of the function buttons.
This device shall contain user preset memory, allowing the user to store setup
data for later retrieval.
In addition to the front panel controls, this device shall be able to be controlled by
an optional serial RS-422 remote controller. This remote controller shall be
available for an additional charge from the device manufacturer.
5.0 Performance Specifications
This device shall employ the use of a CRT with a minimum native resolution of
1000 lines.
The minimum display bandwidth shall be 10MHz, down 3dB.
The device shall accommodate a color temperature of 6500 degrees Kelvin.
This device shall include a built-in audio amplifier and speaker for monitoring
audio sources.
This device shall include a tally light that can be activated from a production
video switcher.
This device shall minimize magnetic field emission through the use of Very low
Frequency (VLF) operation.
This device shall employ the use of a notch filter for minimized dot structure
interference on NTSC and PAL signals.
This device shall employ the use of a mode displaying horizontal and vertical
intervals on the center of the screen.
This device shall include the capability to switch between 4:3 and 16:9 aspect
ratios.
6.0 Dimensional Information
This device shall employ the use of a 14” diagonal (13” viewable) CRT.
This device shall have maximum cabinet dimensions of 13.5 inches high by
13.63 inches wide and 13 inches deep.
This device shall not weigh more than 25 pounds.
7.0 Connectivity Information
This device shall provide for connection of 3 source devices simultaneously,
without employing the use of an external switching device. These connections
shall include the following:
Composite Video on a BNC Connector with loop-through
Audio on an RCA (Phono) Connector with loop-through
Composite Video on a BNC Connector with loop-through
Audio on an RCA (Phono) Connector with loop-through
External Sync on a BNC Connector with loop-through
8.0 Power Requirements
This device shall accept power at 120 V at either 50 or 60 Hz.
This device shall consume no more than 30 watts.
Power to this device shall be supplied via a detachable standard power cord that
is readily available for replacement from local suppliers.
9.0 Safety Compliance Information
This device shall be fully compliant with the following standards:
UL 1950
CSA 22.2 No.950
T V EN-60950 (CE LVD)
FCC Class A
IC Class A
CE EN55022 Class-B / EN50082 - 1 / EN60555 – 2
VCCI-I
10.0 Warranty Information
This device shall carry a 1-year manufacturer’s warranty. Authorized servicing
dealers of the devices’ manufacturer shall perform warranty service.
|