Planar Car Video System PX2211 MW User Manual

 
1
 
The information contained in this document is subject to change without notice.  
This document contains proprietary information that is protected by copyright. All  
rights are reserved. No part of this document may be reproduced, translated to  
another language or stored in a retrieval system, or transmitted by any means,  
electronic, mechanical, photocopying, recording, or otherwise, without prior written  
permission. Windows is a registered trademark of Microsoft Inc.  
Other brand or product names are trademarks of their respective holders.  
2
 
3
 
TABLE OF CONTENTS  
For your safety------------------------------------------------------ 5  
Safety precautions -------------------------------------------6  
Special notes on lcd monitors -----------------------------7  
Before you operate the monitor --------------------------------7  
Features --------------------------------------------------------7  
Packing list ------------------------------------------------------7  
Installation instructions -------------------------------------8  
Controls and connectors ------------------------------------9  
Adjusting the viewing angle------------------------------- 10  
Operating instructions ------------------------------------------- 11  
General instructions ----------------------------------------- 11  
Front panel control -------------------------------------- 12  
How to adjust a setting ----------------------------------- 13  
Adjusting the picture ---------------------------------- 14-17  
Plug and play ----------------------------------------------- 18  
Technical support (FAQ) -------------------------------------- 19  
Error message & possible solution ------------------- 20  
Appendix -------------------------------------------------------------21  
Specifications -------------------------------------------- 21  
Factory preset timing table ------------------------------ 22  
Connector pin assignment ------------------------------ 23-24  
---------------25  
Product registration and technical support  
4
 
FOR YOUR SAFETY  
Before operating the monitor, please read this manual thoroughly. This manual  
should be retained for future reference.  
FCC Class B Radio Frequency Interference Statement  
WARNING: (FOR FCC CERTIFIED MODELS)  
NOTE: This equipment has been tested and found to comply with the limits for a  
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are  
designed to provide reasonable protection against harmful interference in a  
residential installation. This equipment generates, uses and can radiate radio  
frequency energy, and if not installed and used in accordance with the instructions,  
may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or television reception, which  
can be determined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following measures:  
1. Reorient or relocate the receiving antenna.  
2. Increase the separation between the equipment and receiver.  
3. Connect the equipment into an outlet on a circuit different from that to which  
the receiver is connected.  
4. Consult the dealer or an experienced radio/TV technician for help.  
NOTICE:  
1.  
The changes or modifications not expressly approved by the party  
responsible for compliance could void the user's authority to operate the  
equipment.  
2.  
3.  
Shielded interface cables and AC power cord, if any, must be used in order to  
comply with the emission limits.  
The manufacturer is not responsible for any radio or TV interference caused  
by unauthorized modification to this equipment. It is the responsibilities of  
the user to correct such interference.  
WARNING:  
To prevent fire or shock hazard, do not expose the monitor to rain or moisture.  
Dangerously high voltages are present inside the monitor. Do not open the cabinet.  
Refer servicing to qualified personnel only.  
5
 
PRECAUTIONS  
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink,  
laundry tub, swimming pool or in a wet basement.  
Do not place the monitor on an unstable cart, stand, or table. If the monitor falls,  
it can injure a person and cause serious damage to the appliance. Use only a  
cart or stand recommended by the manufacturer or sold with the monitor. If  
you mount the monitor on a wall or shelf, use a mounting kit approved by the  
manufacturer and follow the kit instructions.  
Slots and openings in the back and bottom of the cabinet are provided for  
ventilation. To ensure reliable operation of the monitor and to protect it from  
overheating, be sure these openings are not blocked or covered. Do not place  
the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor  
near or over a radiator or heat register. Do not place the monitor in a bookcase  
or cabinet unless proper ventilation is provided.  
The monitor should be operated only from the type of power source indicated  
on the label. If you are not sure of the type of power supplied to your home,  
consult your dealer or local power company.  
The monitor is equipped with a three-pronged grounded plug, a plug with a  
third (grounding) pin. This plug will fit only into a grounded power outlet as a  
safety feature. If your outlet does not accommodate the three-wire plug, have  
an electrician install the correct outlet, or use an adapter to ground the  
appliance safely. Do not defeat the safety purpose of the grounded plug.  
Unplug the unit during a lightening storm or when it will not be used for long  
period of time. This will protect the monitor from damage due to power surges.  
Do not overload power strips and extension cords. Overloading can result in  
fire or electric shock.  
Never push any object into the slot on the monitor cabinet. It could short  
circuit parts causing a fire or electric shock. Never spill liquids on the monitor.  
Do not attempt to service the monitor by yourself; opening or removing covers  
can expose you to dangerous voltages and other hazards. Please refer all  
servicing to qualified service personnel.  
To ensure satisfactory operation, use the monitor only with UL listed computers  
which have appropriate configured receptacles marked between 100 - 240V AC,  
Min. 5A.  
The wall socket shall be installed near the equipment and shall be easily  
accessible.  
Important Recycle Instruction:  
Lamp(s) inside this product contain mercury and must be recycled or disposed  
of according to local, state or federal laws. For more information, contact the  
electronic industries alliance at WWW.EIAE.ORG. For lamp specific disposal  
information check WWW.LAMPRECYCLE.ORG.  
6
 
SPECIAL NOTES ON LCD MONITORS  
The following symptoms are normal with LCD monitor and do not indicate a  
problem.  
NOTES  
Due to the nature of the fluorescent light, the screen may flicker during initial  
use. Turn off the Power Switch and then turn it on again to make sure the flicker  
disappears.  
You may find slightly uneven brightness on the screen depending on the  
desktop pattern you use.  
The LCD screen has effective pixels of 99.99% or more. It may include blemishes  
of 0.01% or less such as a missing pixel or a pixel lit all of the time.  
Due to the nature of the LCD screen, an afterimage of the previous screen may  
remain after switching the image when the same image has been displayed for  
a long time. The monitor will slowly recover from this.  
When the screen becomes black or flashing, or cannot illuminate any more,  
contact your dealer or service center to replace parts. Don’t repair the screen by  
yourself!  
BEFORE YOU OPERATE THE MONITOR  
FEATURES  
21.5"(546mm) TFT Color LCD monitor  
16:9 Widescreen  
Crisp, Clear Display for Windows  
Recommened Resolutions: 1920X 1080@60Hz  
Ergonomic Design  
Space Saving, Compact Case Design  
CHECKING THE CONTENTS OF THE PACKAGE  
The product package should include the following items:  
1. LCD monitor  
2. Base  
3. User's Guide  
4. Power Cord  
5. D-sub Cable  
.
DVI Cable  
6
7. Audio Cable  
7
 
INSTALLATION INSTRUCTIONS  
BASE  
The monitor is supplied complete with a stand.If you prefer to wall mount the monitor,  
please follow the instructions below to remove the stand.Be sure to include the stand  
with the monitor if it is necessary to return the unit.  
CAUTION  
Put the monitor on a stable surface.The monitor may cause injury  
or damage if it falls or is dropped.  
Do not give a strong impact to the monitor.It may cause damage.  
Ƶꢀ  
Ƶꢀ  
ƵꢀUnplug the monitor before removal or installation to avoid electric  
shock or damage.  
<Installation>  
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.  
ķ
ꢀꢁꢂꢃthe monitor flat on a table with front face down.  
Install the Stand-Base to the Monitor.  
Av‘ꢃ‡urꢃ€‚v‡‚ꢄꢃ‡‚ꢃ‡urꢃ†‡ꢁqꢃiꢂꢃˆ†vtꢃ‡urꢃ†prꢅꢃPprꢃ†prꢃv†ꢃ†rpˆꢄryꢂꢃsꢁ†‡rrqꢆꢃƒˆ†uꢃq‚ꢃ  
urꢃx‚iꢃ‚ꢃ‡urꢃ†prꢅ  
ĸ
Ĺ
The knob of the screw  
push down  
Stand-Base  
Screw for Stand-Base fixing  
<Remove>  
Put a piece of soft cloth on the table beforehand to prevent the monitor from being scratched.  
ķ
ꢀꢁꢂꢃthe monitor flat on a table with front face down.  
Pull up the knob of the screws, and remove the screw and the Stand-Base.  
ĸ
<Stopper pin>  
Please stand the monitor and then remove the  
stopper pin on the back of the stand slowly while  
pushing top face of the stand before you install the  
monitor. Careful attention is required as the monitor  
is sprung loaded and may expand quickly when  
removing it.  
Stopper pin  
8
 
CONTROLS AND CONNECTORS  
SIGNAL CABLE  
Connecting the Signal Cable: Plug one end of the signal cable to the LCD monitor  
and the other end to a computer or a video source.  
Connecting the Power Cord: Plug the AC-power cord one end to LCD monitor’s  
AC input socket , the other end to Wall outlet.  
Connecting the Audio Cable: Connect the audio cable between the monitor's  
audio input and the PC's audio output.  
Caution: If the AC outlet is not grounded (with three holes), install the proper  
grounding adapter (not supplied).  
Figure 2 Connecting Cables  
1. Power Cable  
2. HDMI Cable  
3
4
5
DVI Cable  
D-SUB Cable  
Audio Cable  
9
 
ADJUSTING THE VIEWING ANGLE  
For optimal viewing it is recommended to look at the full face of the monitor,  
then adjust the monitor’s angle to your own preference.  
Hold the stand so you do not topple the monitor when you change the  
monitor’s angle.  
You are able to adjust the monitor’s angle from -5to 19.  
19°  
-5°  
Figure 3  
NOTES  
Do not touch the LCD screen when you change the angle. It may cause damage  
or break the LCD screen.  
Careful attention is required not to catch your fingers or hands when you  
change the angle.  
10  
 
OPERATING INSTRUCTIONS  
GENERAL INSTRUCTIONS  
Press the power button to turn the monitor on or off. The other control buttons are  
located at front panel of the monitor (See Figure 4). By changing these settings, the  
picture can be adjusted to your personal preferences.  
The power cord should be connected.  
Connect the video cable from the monitor to the video card.  
Press the power button to turn on the monitor position. The power indicator  
will light up.  
Figure 4 External Control Button  
EXTERNAL CONTROLS  
1. Source/AutoAdjust/EXIT  
button  
ECO (-)  
2.  
3. Volume Hotkey(+)  
4. Menu / Enter  
5. Power Indicator  
6. Power button  
11  
 
FRONT PANEL CONTROL  
Power Button:  
Press this button to switch ON/OFF monitor’s power.  
Power Indicator :  
Blue --- Power On mode.  
Orange --- Power saving mode.  
MENU/ENTER:  
Activates OSD menu or function adjust confirm .  
ECO/(-)  
Activates the ECO control when the OSD is OFF or navigate through adjustment icons  
when OSD is ON or adjust a function when function is activated.  
Volume/+:  
Activates the volume control when the OSD is OFF or navigate through adjustment  
icons when OSD is ON or adjust a function when function is activated.  
Source/Auto Adjust/Exit:  
When the OSD is OFF, pressing Auto/Source button will toggle between sources.  
Press continuously to select the input source indicated in the message bar.Press  
Menu/Enter button to change to the selected source.  
Auto configure hot key:(VGA input only) When the OSD is OFF,press and hold down  
the button for 2 seconds to auto configure.  
when OSD menu is ON, this button will act as a Exit Key (Exit OSD menu)  
OSD Lock Function: To lock the OSD, press and hold the MENU button while the  
monitor is off and then press power button to turn the monitor on. To un-lock the  
OSD - press and hold the MENU button while the monitor is off and then press  
power button to turn the monitor on.  
NOTES  
Do not install the monitor in a location near heat sources such as radiators or air  
ducts, or in a place subject to direct sunlight, or excessive dust or mechanical  
vibration or shock.  
Save the original shipping carton and packing materials, as they will come in  
handy if you ever have to ship your monitor.  
For maximum protection, repackage your monitor as it was originally packed at  
the factory.  
To keep the monitor looking new, periodically clean it with a soft cloth.  
Stubborn stains may be removed with a cloth lightly dampened with a mild  
detergent solution. Never use strong solvents such as thinner, benzene, or  
abrasive cleaners, since these will damage the cabinet. As a safety precaution,  
always unplug the monitor before cleaning it.  
It may cause permanent damage  
.
do not scratch the screen with hard things,  
Don’t leak liquid into monitor which will result in the damage of component  
12  
 
HOW TO ADJUST A SETTING  
1. Press the MENU-button to activate the OSD window.  
2. Press + or - to navigate through the functions. Once the desired function is  
highlighted, press the MENU-button to activate it. If the function selected has a  
sub-menu, press + or - again to navigate through the sub-menu functions.  
Once the desired function is highlighted, press MENU-button to activate it.  
3. Press + or - to change the settings of the selected function.  
4. To exit and save, select the exit function. If you want to adjust any other  
function, repeat steps 2-3.  
Figure 5 The OSD Message  
13  
 
ADJUSTING THE PICTURE  
Main  
Menu  
Icon  
Main Menu  
Item  
Sub  
Menu  
Description  
Enhances Contrast Ratio  
Note: When this function is turned "On" you cannot  
adjust the current settings for Contrast, Brightness,  
ECO mode or Gamma.  
(VGA input  
only)  
(VGA input  
only)  
(VGA input  
only)  
(VGA input  
only)  
14  
 
Main  
Menu  
Icon  
Main Menu  
Item  
Sub  
Menu  
Description  
15  
 
Main  
Menu  
Icon  
Main Menu  
Item  
Sub  
Menu  
Description  
16  
 
Main  
Menu  
Icon  
Main Menu  
Item  
Sub  
Menu  
Description  
17  
 
PLUG AND PLAY  
Plug & Play DDC 2B Feature  
This monitor is equipped with VESA DDC 2B capabilities according to the VESA  
DDC STANDARD. It allows the monitor to inform the host system of its identity and,  
depending on the level of DDC used, communicate additional information about  
its display capabilities.  
The DDC 2B is a bidirectional data channel based on the I2C protocol. The host can  
request EDID information over the DDC 2B channel.  
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO  
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE  
MUST BE A VIDEO INPUT SIGNAL.  
This monitor meets the Green monitor standards as set by the Video Electronics  
and The Swedish Confederation Employees (NUTEK).  
Standards Association (VESA)  
consumption  
This feature is designed to conserve electrical energy by reducing power  
when  
there is no video-input signal present. When there is no video input signal  
this monitor, following a time-out period, will automatically switch to an OFF mode.  
This reduces the monitor's internal power supply consumption. After the video  
input signal is restored, full power is restored and the display is automatically  
redrawn. The appearance is similar to a "Screen Saver" feature except the display is  
completely off. The display is restored by pressing a key on the keyboard, or  
clicking the mouse.  
18  
 
TECHNICAL SUPPORT (FAQ)  
Problem & Question  
Possible Solution  
*Check if the Power Switch is in the ON  
position  
Power LED is not on  
*Power Cord should be connected  
*Check if the PC system is Plug & Play  
compatible  
*Check if the Video Card is Plug & Play  
compatible  
No Plug & Play  
Picture is fuzzy  
*Check if the D-15 plug pin of Video Cable  
is bent  
*Adjust the Contrast and Brightness  
Controls.  
*Move electrical devices that may cause  
electrical interference.  
Picture bounces or a wave  
pattern is present in the picture  
*Computer Power Switch should be in the  
ON position.  
*Computer Video Card should be snugly  
seated in its slot.  
*Make sure monitor’s video cable is  
properly connected to the computer.  
*Inspect monitor’s video cable and make  
sure none of the pins are bent.  
*Make sure computer is operational by  
hitting the CAPS LOCK key on the  
keyboard while observing the CAPS LOCK  
LED. The LED should either turn ON or  
OFF after hitting the CAPS LOCK key.  
The power LED is ON but there’s  
no video or no picture.  
Missing one of the primary colors *Inspect the monitor’s video cable and  
(RED, GREEN, or BLUE)  
Screen image is not centered or  
sized properly.  
Picture has color defects  
(white does not look white)  
make sure that none of the pins are bent.  
*Adjust pixel frequency (CLOCK) and FOCUS  
or press hot-key (AUTO).  
*Adjust RGB color or select color  
temperature.  
*Use win 95/98 shut-down mode Adjust  
CLOCK and FOCUS or perform hot- key  
(AUTO-key).  
Horizontal or vertical disturbances  
on the screen  
CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal  
sweep. If the frequency is not correct, the screen shows vertical stripes and the  
picture has not correct width.  
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment  
the picture has horizontal disturbances in light picture.  
For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98 shut-down mode  
pattern.  
19  
 
ERROR MESSAGE & POSSIBLE SOLUTION  
NO SIGNAL :  
1.  
2.  
Check that the signal-cable is properly connected , If the connector is loose,  
tighten the connector’s screws.  
Check the signal-cable’s connection pins for damage.  
INPUT NOT SUPPORT :  
Your computer has been set to unsuitable display mode ,set the computer to  
display mode given in the following table.  
20  
 
APPENDIX  
SPECIFICATIONS  
Driving system TFT 21.5"Color LCD  
Viewable  
546mm diagonal  
Image Size  
LCD Panel  
Input  
Pixel pitch 0.248˄H˅× 0.248˄v˅  
R, G, B Analog Interface  
DVI  
HDMI  
Video  
Separate Sync. H/V TTL  
H-Frequency Analog:24-80kHz,Digital:30kHz–83kHz  
V-Frequency Analog&Digital:56-76Hz  
170MHz  
Dot Clock  
Max. Resolution  
Plug & Play  
1920x1080@60Hz  
VESA DDC2B TM  
43W(TYP)  
ON Mode  
Power Consumption  
OFF Mode ≤1W  
D-Sub mini 15 pin, DVI-D 24 pin, HDMI  
Input Connector  
Analog:0.7Vp-p(Standard)75Ω, Positive  
Digital:DVI(Digital Visual Interface  
Standard Rev.1.0) compliance  
Digital:HDMI(1.3)  
Input Video Signal  
Power Source  
100~240VAC,50/60Hz  
Operating Temp: 5° to 40°C  
Environmental  
Considerations  
Storage  
Temp.: -20° to 60°C  
Operating umidity:15% to 90%  
H
Dimension  
Weight (N. W.)  
512.7(W)X398.1(H) X249.7(D)  
6.3 kg  
Power Consumption ( Maximum )  
52Watts  
UL cUL, CE , FCC B  
/
Regulatory Compliance  
21  
 
FACTORY PRESET TIMING TABLE  
HORIZONTAL  
FREQUENCY(kHZ)  
VERTICAL  
FREQUENCY(Hz)  
STANDARD  
RESOLUTION  
640 x 480  
640 x 480  
640 x 480  
640 x 480  
720 x 400  
800 x 600  
800 x 600  
800 x 600  
800 x 600  
832 x 624  
1024 x 768  
1024 x 768  
1024 x 768  
1024 x 768  
1280 x 1024  
1280 x 1024  
1440 x 900  
1440 x 900  
1680 x1050  
1920 X1080  
31.469  
35  
37.861  
37.5  
59.94  
66.667  
72.809  
75  
70.087  
56.25  
60.317  
72.188  
75  
74.551  
60.004  
70.069  
72.074  
75.029  
60.02  
VGA  
Mac VGA  
Dos-mode  
31.469  
35.156  
37.879  
48.077  
46.875  
49.726  
48.363  
56.476  
57.5  
60.023  
67.981  
79.976  
55.935  
70.635  
65.29  
SVGA  
Mac SVGA  
XGA  
SXGA  
75.025  
59.887  
74.984  
59.954  
59.887  
WXGA+  
WSXGA+  
HDTV  
66.295  
22  
 
CONNECTOR PIN ASSIGNMENT  
1
6
5
10  
11  
15  
15 - Pin Color Display Signal Cable  
PIN NO.  
DESCRIPTION  
PIN NO.  
DESCRIPTION  
+5V  
Detect Cable  
Ground  
DDC-Serial Data  
H-Sync  
V-Sync  
1.  
2.  
3.  
4.  
5.  
6.  
7.  
8.  
Red  
Green  
Blue  
Ground  
Ground  
R-Ground  
G-Ground  
B-Ground  
9.  
10.  
11.  
12.  
13.  
14.  
15.  
DDC-Serial Clock  
24 - Pin Color Display Signal Cable  
PIN NO.  
DESCRIPTION  
PIN NO.  
DESCRIPTION  
1.  
2.  
3.  
TMDS Data 2-  
TMDS Data 2+  
TMDS Data 2/4  
Shield  
13.  
14.  
15.  
TMDS Data 3+  
+5V Power  
Ground(for+5V)  
4.  
5.  
6.  
7.  
TMDS Data 4-  
TMDS Data 4+  
DDC Clock  
16.  
17.  
18.  
19.  
Hot Plug Detect  
TMDS Data 0-  
TMDS Data 0+  
TMDS Data 0/5  
Shield  
TMDS Data 5-  
TMDS Data 5+  
TMDS Clock Shield  
DDC Data  
8.  
9.  
10.  
11.  
N.C.  
20.  
21.  
22.  
23.  
TMDS Data 1-  
TMDS Data 1+  
TMDS Data 1/3  
Shield  
TMDS Clock +  
TMDS Clock -  
12.  
TMDS Data 3-  
24.  
23  
 
Pin  
No.  
Pin  
No.  
Signal Name  
Pin No.  
Signal Name  
Signal Name  
1
TMDS Data 2+  
9
TMDS Data 0  
17  
DDC/CEC  
Ground  
2
3
TMDS Data 2  
Shield  
TMDS Data 2  
10  
11  
TMDS Clock +  
18  
19  
+5V Power  
TMDS Clock  
Shield  
Hot Plug  
Detect  
TMDS Clock  
4
5
TMDS Data 1+  
12  
13  
TMDS Data  
1Shield  
CEC  
TMDS Data 1  
6
14  
Reserved (N.C.  
on device  
7
8
TMDS Data 0+  
15  
16  
SCL  
TMDS Data 0  
Shield  
SDA  
24  
 
Product Registration and Technical Support  
Register Your Planar Products Today  
Thank you choosing Planar. To assure you receive all the benefits of your Planar  
product and services, register your Planar product today.  
Visit our website to register your productat  
Cables, Replacement Lamps, Accessories  
To find cables, replacement lamps and accessories for your Planar projector, LCD  
monitor, touch screen or other Planar products visit our online store at  
Technical Support  
manuals, touch screen drivers, warranty information and access to Planar's  
Technical Library for online troubleshooting.  
To speak with Planar Customer Support please have you model and serial number  
available and dial:  
Planar Support  
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US. Hours: 24  
hours a day, 7 days a week.  
Toll or long distance charges may apply.  
25  
 
 
 
 
 
Q41G22M1935 1A  
 

Pelco Switch CM9700UTP32A User Manual
Pentax Binoculars 10X50PIF User Manual
Philips Cable Box 22IE User Manual
Philips Car Speaker SB365 User Manual
Philips Charcoal Grill HD 4631 User Manual
Philips CRT Television 13PR19C1 User Manual
Philips DVD Player BDP5110 User Manual
Philips Work Light HO User Manual
Plantronics Headphones CS510 User Manual
Poulan Snow Blower 421916 User Manual