S I M P L Y
A M A Z I N G ™
USER’S GUIDE
LOW BOY
INDUSTRIAL
FLOOR MACHINE
LB8005
•IMPORTANT•
SAVE THIS BOOKLET!
Includes:
• Safety Warnings
• Warranty
• Operating Instructions
• Trouble Diagnosis
• Accessories
IMPORTANT:
Warranty
Where Necessary for Plug to be Fitted
ORECK MANUFACTURING COMPANY: (ORECK gives you the
following limited warranty for this product only if it was originally
purchased for use, not resale, from ORECK or an ORECK Authorized
Retail Dealer.)
The wires in this mains lead are coloured in accordance with the
following code:
Blue: Neutral
Brown: Live
Green: Earth
ORECK will repair or replace, free of charge, to the original purchaser,
any part which is found to be defective in material or workmanship
within one (1) year of the date of original purchase.
As the colours of the wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the terminals in your
plug, proceed as follows;
PAD DRIVER, CARPET BONNET, LAMBS WOOL BONNET,
BRUSHES, PADS and other parts subject to normal wear are not
covered by this limited warranty.
The wire which is coloured Blue must be
13 AMP FUSE
E
GREEN
connected to the terminal which is
marked with the letter N or coloured
Black.
This limited warranty does not apply to any part subjected to accident,
abuse, or alteration, misuse, damage caused by fire or act of God, the
use of voltages other than indicated on the serial number plate of this
product or service of this product by other than ORECK or an ORECK
Factory Authorized Service Center.
The wire which is coloured Brown must
be connected to the terminal which is
marked with the letter L or coloured Red.
L
N
Green is to be connected to the earth pin
of the 3 pin plug.
BROWN
CORD CLAMP
ORECK does not authorize any person or representative to assume or
grant any other warranty obligation with the sale of this product.
BLUE
The wire which is coloured Green must
be connected to the terminal which is
marked with the letter E.
ORECK’S limited warranty is valid only if you retain proof of purchase
from ORECK or an ORECK Authorized Retail Dealer for this product. If
you purchase this product from any other source, your purchase is “AS
IS,” which means ORECK grants you no warranty, and that you, not
ORECK, assume the entire risk of the quality and performance of this
product, including the entire cost of any necessary servicing or repairs
of any defects.
If a 13 amp plug is fitted, fit a 13 amp fuse.
Low Boy Model LB8005 is
intended for Commercial Use.
ORECK’S liability for damages to you for any costs whatsoever arising
out of this statement of limited warranty shall be limited to the amount
paid for this product at the time of original purchase, and ORECK shall
not be liable for any direct, indirect, consequential or incidental
damages arising out of the use or inability to use this product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not
apply to you.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT,
INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO THE WARRANTY PERIOD, AND NO WARRANTIES,
WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER THIS
PERIOD.
Some states do not allow limitations on the duration of implied
warranties, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
3
To Guide the Machine
Operating Instructions
Hold the handle with both hands and push with the palms of your hands
to move in the forward direction, then cup your hands and pull to bring
back. The design of the machine eliminates the fatigue associated with
controlling other floor machines.
WARNING: Unplug cord from electrical
outlet before servicing and when leaving
unattended.
Care of your Oreck Low Boy Floor Machine
This is a precision machine. Dropping unreasonable bumping or rough
handling may result in damage. Remove brushes after use. The bristles
may be damaged due to the weight of the machine. Store your machine
in the upright position. After each use, remove wax or cleaning
solutions. After sanding, blow sawdust off motor and locking
mechanism.
To Operate:
IMPORTANT - Always wear shoes
when using your Low Boy.
Raise the handle pin release with foot.
Lubrication: With the handle in its
lowest position, periodically place one
drop of oil (3-in-One) on the thrust
bearings.
Lean handle back. While handle is
released and with both hands on
handle grips, squeeze the ON/OFF
lever located on the right grip to turn
on.
THRUST BEARINGS
Troubleshooting Guide
WARNING: Unplug cord from electrical
outlet before servicing.
To Attach the Drive Pad Holder or
Brush:
PROBLEM
POSSIBLE SOURCE
AREAS TO CHECK
Lay the machine on its back to reveal
the bottom pan. Align the indentations
in the pad holder with the brackets
around the bottom pan. Place your
hands on opposite sides of the pad
holder and using the heel of your
hands, push the pad holder onto the
pan.
Not plugged in
properly.
Be sure cleaner is
firmly plugged into
wall outlet.
FLOOR MACHINE
WILL NOT RUN
No electricity in wall
outlet.
Check electrical
source–fuse or
circuit breaker.
Motor circuit
breaker has
tripped.
Reset motor circuit
breaker.
Use the included key to rotate the
swing arms clockwise to lock the pad
holder to the bottom pan. Place a pad
on the floor and position the machine
so that as the handle is raised the pad
holder is centered on the pad.
HANDLE WILL NOT
UNLOCK
Locking pin needs
cleaning
Clean locking
mechanism
HANDLE IS HARD TO
RAISE OR LOWER
Lower handle pivot
bearings need oiling
Oil pivot bearings.
ALL OTHER SERVICING SHOULD BE DONE BY AN
ORECK AUTHORIZED SERVICE CENTER.
To Attach the Pad:
Lay the floor machine on its back with
the handle lying on the floor. This
exposes the brush holder pan. Just
place the pad over the round brush
holder pan making sure it is in place.
CALL CUSTOMER SERVICE HOT LINE
0800 67 68 69
Whenever calling, please be sure to have your model and serial
number from data plate.
CAUTION: NEVER put the pad on the
machine by placing it on the floor and
moving the running machine over it, or
placing the machine over the pad and
then starting the motor.
53307-01 REV A
8/01 ECN# R-6062
© 2001 Oreck Holdings, LLC. All Rights Reserved. All word marks, logos, regestered trademarks and product configurations are
owned and used under the authorization of Oreck Holdings, LLC.
4
|