RM24930
Universal Remote
Instruction Manual
Button Functions
Button Functions, cont.
SETUP Used to setup
the remote, and for
code search function.
ON-OFF Turns
product On or Off.
Some buttons on the remote might have functions that
are referred to by different names on the device you are
controlling. E.G. PREV.CH may be called RECALL, or
ENTER may be called DISPLAY. These differences
depend on the brand and model of your product. Also,
this remote can only operate features that exist on your
product. E.G., your product must have PREV.CH ability
for the PREV.CH button to operate this feature.
SLEEP enables the remote
to turn off your TV after a
period of 1 to 99 minutes.
MUTE Turns off the
TV sound while the
picture remains.
TV, CBL/SAT, VCR, DVD/
AUX Selects product to
be operated.
Red Indicator
Lights when any
button is pressed.
PREV.CH Returns to
the previously selected
channel.
VOLUME UP/DOWN
Changes the volume
level of the product,
normally the TV.
CHANNEL Up/Down
Changes the channels.
The Channel buttons
also control DVD SKIP
functions.
INFO Shows the date
and time if your TV or
VCR has that feature.
Works the same way as
a Display button.
INPUT Selects the
video inputs of your
TV if equipped with
that feature.
MENU Brings up device
Main Menu. Use Chan
and Vol buttons as cursor
buttons and Mute as Okay.
Press TV to Exit.
0-9
Enter numbers for direct
channel selection. Some
products require ENTER
to be pressed after
ENTER
Used to complete
channels selection for
some brands of TV. Also
used to complete the
code entry process.
channel selection.
TV/VCR Operates the TV/
VCR function of your VCR.
RECORD, PLAY, STOP,
REW, FF, PAUSE VCR
control buttons operate
your VCR even when the
remote is set to operate
the TV. Also operates DVD
Scan -/+. Note the VCR
buttons also control DVD
when in DVD Mode.
Note: The REC button must be pressed TWICE to
record from your VCR. For some brands of VCRs, you
might need to press the REC button once, then press it
again for three seconds.
4
5
Menu Operation
Direct Code Entry
The Menu button puts the remote in and out of
Menu Mode. Pressing Menu brings up your
device Menu. While in Menu mode the remote’s red
indicator light blinks continuously. The remote will
exit Menu Mode after 20 seconds if no keys are
pressed.
1. Press and hold the SETUP button until
the red indicator stays on, then release
the SETUP button.
2. Press and release the desired device
button (TV, VCR, etc.). The red indicator
blinks, then stays lit.
When in Menu Mode, the Menu, Channel, Volume,
Mute and Device keys operate as follows:
3. Enter the 4 digit code
from the code tables
(on separate sheet).
Note: after a valid code
entry, the red indicator
turns off. For an invalid
code, the red indicator
flashes.
MENU Enters Menu mode.
CHANNEL UP/DOWN Cursor Up/Down for Menu
navigation.
VOLUME UP/DOWN Cursor Right/Left for Menu
navigation.
4. With your device on, press ON/OFF.
If the device turns off, no further
programming is required. Note: If
some buttons do not operate your
equipment, try one of the other
codes for your brand.
MUTE (OK) command for Menu selections.
Press TV or any other Device key to Exit, Clear, or
Quit the Device Menu and return the remote to
normal operation (red indicator will turn off).
Write your codes down here for easy reference
later.
For certain RCA, GE, and ProScan devices,
pushing the MENU button selects the highlighted
item. The numeric buttons may also be used to
select the MENU choice.
Note: Some functions in some brands might not be
fully supported.
Device
Device stored Code
TV
TV
CBL/SAT
VCR
DVD/AUX
6
7
Code Search
UsingYour Remote
If your device does not respond after you have tried
all the codes for your brand, or if your brand is not
listed, try searching for your code by following these
steps.
Code Identification
The Code Identification Feature allows you to
identify the four digit library code stored under your
device button. For example, if you want to find out
what four digit code is stored under your TV device
button, follow the six steps below:
1. Manually turn on the device (TV, VCR, etc.) to be
controlled.
2. Press and hold the SETUP button until
the red indicator stays on, then
release the SETUP button.
1. Press and hold the SETUP button until
the red indicator stays on. Release the
SETUP button.
3. Press and quickly release the desired
device button (TV, VCR, etc.). The red
indicator blinks off once.
2. Press and release the desired device
button (TV, VCR, etc.). The red
indicator blinks, then stays lit.
4. Press the ON-OFF button repeatedly
(up to 300 times) until the device to
be controlled turns off. The red
indicator blinks off with each button
press.
3. Press and release the SETUP button.
The red indicator blinks once and
remains lit.
4. To find the first digit for
the code stored under
the device button
5. Press and release ENTER to install the
code.
pressed in step 2,
press each numeric
button from 0-9 in
turn. The number that
causes the indicator
light to blink is the
Most users will store VCR codes under the VCR button,
Cable codes under CABLE, etc. If (for example) you
want to store a VCR code under DVD/AUX, first follow
the procedure for Direct Code Entry (previous page)
and press DVD/AUX in step 2 of Direct Code Entry, then
enter ANY VCR code in step 3 of Direct Code Entry.
Then follow the steps above for Code Search.
first digit in your code.
5. To find the second digit, repeat step 4.
Note: Code Search starts from the currently stored
four digit number under that mode. Sometimes the
first code that “works” with your device may only allow
limited functionality (e.g. the MENU button might not
work). There may be a code that performs more
functions. Continue the code search process until the
best code is found.
6. Repeat step 4 to find the third and fourth digit.
This time the red indicator turns off and stays off.
8
9
UsingYour Remote, cont.
UsingYour Remote, cont.
Sleep Function
Controlling Devices with Separate
Power On and Off Buttons
The Sleep button enables the remote to turn off
your TV after a period of 1 to 99 minutes as shown
below. The remote must be in TV mode to set a
Sleep Timer. This feature works even if your TV
does not have a sleep feature.
Some GE, RCA and ProScan models require you to
press the device button for more than one second
to turn the device on and the ON•OFF button to turn
the device off.
1. Press and release the TV device button.
Controlling Combo Devices
Some Combo devices (e.g. TV/VCR, TV/DVD,
DVD/VCR, etc.) will require you to set up two
different Mode buttons to control both parts of the
Combo device. For example, if you have a TV/DVD
Combo, you might need to set up one code under
the TV button to control the TV part AND a
separate code (under any other Mode button) to
control the DVD part.
2. Press and hold the Sleep button until the
LED remains lit (about 2-3 seconds).
3. Release the Sleep button.
4. Press and release the
numeric buttons (01-
99) for the time
required. The LED will
blink off to indicate
button press accep-
tance.
VCR/DVD Punch-Through
This remote allows the 6 VCR transport buttons
(i.e. PLAY, PAUSE, STOP, FF, REWIND, and REC)
to Punch-Through control from any Mode
programmed with TV, SAT or Cable codes to the
last VCR, or DVD programmed Mode you used.
This feature will not operate if the programmed TV,
SAT or Cable code has its own VCR transport
button control e.g. a TV Combo, SAT/PVR, etc.
5. TV Sleep Timer is set.
6. Leave the Remote pointing towards the TV
with an unobstructed path.
To cancel the Sleep Timer, press and hold the
Sleep button until the LED blinks, or press and
release the Power button in TV mode.
10
11
UsingYour Remote, cont.
UsingYour Remote, cont.
Volume/Mute Control and Punch-
Through
Setting any Mode to use its own
Volume/Mute Control
This remote lets you select which device Mode
controls your Volume/Mute buttons. The remote is
initially set for all device Modes to use their own
Volume/Mute control if present. If the programmed
code has no Volume/Mute operation of its own then
those buttons will punch-through control to the TV
Mode device without needing to change to TV
Mode.
This routine can set any Mode to use only its own
Volume/Mute control. Note - If your chosen Mode
has no Volume/Mute functions of its own then the
Volume/Mute buttons will do nothing.
1. Press and hold the SETUP button until
the red indicator turns on, then release
the button.
2. Press and hold the MUTE button until
the red indicator blinks off, then release
the button.
Any Mode chosen for Volume/Mute control
MUST have its own Volume/Mute function or
the Volume/Mute buttons will do nothing.
3. Press and release the desired Mode
button (TV, VCR, etc.), the red indicator
blinks then stays on.
Setting ALL Volume/Mute Control to
any one Mode
This routine can set all Modes to “punch-through” to
any one chosen Mode for Volume/Mute button
control without the needing to change to that Mode.
4. Press and release the VOLUME-
(Down) button, the red indicator blinks
then stays on.
1. Press and hold the SETUP button until
the red indicator turns on, then release
the button.
5. Press and release the MUTE button and
the red indicator turns off.
2. Press and hold the MUTE button until the
red indicator blinks off, then release the
button.
Your chosen Mode will now use its own Volume/
Mute control.
3. Press and release the desired Mode button
(TV, VCR, etc.) for Volume/Mute control,
the red indicator blinks then stays on.
4. Press and release the MUTE button and
the red indicator turns off. The red indicator
will blink rapidly for three seconds if the
Mode you have selected has no Volume/
Mute control.
All other Modes will now punch-through to your
chosen Mode for Volume/Mute control.
12
13
Troubleshooting
90 Day Limited Warranty
Remote does not operate your product.
Jasco Products Company warrants this product to
be free from manufacturing defects for a period of
ninety days from the original date of consumer
purchase. This warranty is limited to the repair or
replacement of this product only and does not
extend to consequential or incidental damage to
other products that may be used with this unit. This
warranty is in lieu of all other warranties express or
implied. Some states do not allow limitations on
how long an implied warranty lasts or permit the
exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to
you. This warranty gives you specific rights, and
you may also have other rights which vary from
state to state. If unit should prove defective within
the warranty period, return prepaid with dated proof
of purchase to:
•
Press the device button of the product you want
to control.
•
•
Program the remote with a new code.
Install new batteries. (You might have to
reprogram your remote after installing new
batteries.)
•
Remote may not be compatible with your
product.
Remote does not operate some features of
your product.
•
•
Sometimes a particular code might operate
some features but not all. Try programing
remote with a new code.
Remote may not be able to operate all features
of your product or button names might be
different than your product.
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK 73114
Red Indicator blinks after you program a
product code.
•
•
Remote did not accept the code.
Try to program the code again or try a different
code.
Lost Your Codes?
Enclosed with this remote is a sticker on which you
should write the codes for each device you
programmed. Apply the sticker to the back of the
remote or somewhere convenient for future
reference.
Also on the sticker is our website address which,
should you lose your codes or programming
instructions, you can find available on our website:
14
15
RM24930
Universal Remote
Instruction Manual
Jasco Products Company
311 N.W. 122nd
Oklahoma City, OK 73114
Made in China
RM24930-02/05
|