Heritage
HIGH-PE
OSCILLATING TABLE FANS
Owner’s Guide and
Installation Manual
Models
90302
97302
Form 44800
20081024
©2008 Hunter Fan Co.
WelCome
UnpaCkIng
Thank you for choosing Hunter’s
12-Inch High-Performance Table
Fan. This manual gives you com-
plete instructions for using your fan.
Here are some the features you will
enjoy with your fan:
As you unpack the fan, save the
carton and packing materials in
case you want to move or ship the
unit in the future.
Carefully remove all items from the
box.
• An attractive design that enhanc-
es any decor
NOTE: It is best to have someone
hold the box while you lift the fan
and the protective packaging out of
the carton.
• A powerful Hunter motor for max-
imum air flow
• Three speeds to adjust your
comfort level
Make sure all shipping materials
are removed from fan before oper-
ating.
Before installing your fan, record
the following information for your
records and for warranty assis-
tance.
Model Name _________________
Date Code ___________________
Date Purchased_______________
Where Purchased _____________
Please attach your receipt
or a copy of your receipt
to this manual for future
reference.
3
groUndIng InStrUCtIonS
This appliance is for household use
LINE CORD SAFETY TIPS
only and may be plugged into any
120-volt AC electrical outlet (ordi-
nary household current). DO NOT
use any other type of outlet.
1. NEVER pull or yank on the cord
or the appliance.
2. To insert plug, grasp it firmly
and guide it into the outlet.
3. To disconnect the appliance,
grasp the plug and remove it
from the outlet.
WarnIng
This unit is suitable for grounded
receptacle use only.
4. Before each use, inspect the
line cord for cuts and/or abra-
sion marks. If any are found,
the appliance should be
serviced and the line cord re-
placed. Please return it to our
Service Department or to an
authorized service representa-
tive.
The cord has a grounded plug as
shown in Figure 1. An adapter, as
shown in Figure 2, is available for
connecting three-blade grounding-
type plugs to two-slot receptacles.
The green grounding lug extending
from the adapter must be con-
nected to a permanent ground such
as a property grounded outlet box.
The adapter should not be used if
a three-slot grounded receptacle is
available.
5. NEVER wrap the cord tightly
around the appliance, as this
could place undue stress on the
cord where it enters the appli-
ance and could cause it to fray
and break.
6. DO NOT operate appliance if
the line cord shows any dam-
age, if the appliance works
intermittently or stops working
entirely.
Grounded
Plug
Adapter
Metal
Screw
Grounding Pin
Grounded Outlet
Box Cover
Grounded Outlet
Cover Box
Grounding
Means
FIgURE 1
FIgURE 2
4
operatIon
This appliance is for household use
only.
3.Turn the fan “ON” or “OFF” by
sliding the Power/Speed Con-
trol to the up or down. The
power should always be OFF
before unplugging the fan.
1. Place the fan on a dry, safe, flat
surface where it cannot fall or
be pulled by the cord.
4. To select the speed, move the
Power/Speed Control up from
OFF (O) to the desired speed
setting: Low, Medium. or High.
2. Plug the fan into a grounded
120-volt AC electrical outlet (or-
dinary household current).
DO NOT use any other type
of outlet. Make sure that the
rated voltage of the fan is the
same as the power source be-
fore plugging it into the power
source.
5. To make the fan oscillate, push
the oscillation pin down. To stop
oscillating, pull the oscillation
pin up.
Handle
Oscillation
Pin
Power / Speed
Control Switch
HERITAGE mODEL
FIgURE 3
5
maIntenanCe
This fan is permanently lubricated
and will not require additional lubrica-
tion (oil) for the life of the fan.
2.Disassemble grilles by carefully
removing the grille Ring Screw
on the bottom of the grille and
removing the grille Ring. See
Figure 4.
This fan requires little maintenance
and contains no user serviceable
parts. DO NOT try to fix it yourself.
Contact qualified service personnel
if servicing is needed.
Grille
Ring
TO CLEAN:
1. Before cleaning, turn fan off and
unplug from electrical outlet.
Wipe off excess dust with a lint-
free cloth.
2. To ensure adequate air circulation
to the motor, keep vents located
at the rear of the motor hous-
ing free from dust accumulation.
A vacuum cleaner hose can be
used to clean these vents.
Grille Ring
Screw
FIgURE 4
3. DO NOT immerse the fan in wa-
ter or any other liquid.
3.grilles and blades may be cleaned
with soft cloth dampened with
mild soap and water.
CLEANINg gRILLE AND BLADE:
4. Use a soft, slightly damp cloth to
wipe the remaining fan parts.
1. Turn the fan off and unplug from
the electrical outlet.
5. DO NOT allow water or any other
liquid to get into the motor hous-
ing or base.
6. After the Blades and grilles have
dried completely, reassemble the
fan. Reposition the grille Ring so
that the grille Ring Screw is at
the bottom of the grilles. Careful-
ly align the grille Ring Screw into
its holes and tighten it so that the
grille Ring is securely in place.
DO NOT OVERLY TIgHTEN.
7. DO NOT plug fan into an electri-
cal outlet until it has been fully
reassembled.
6
Storage
troUbleShootIng
1.Keep the original packaging for
the purpose of storing the fan.
PROBLEM
• Can not turn on fan.
2. ALWAYS store the fan in a dry
place.
SOLUTION
• Make certain the fan is plugged
in and that the power outlet has
power.
3. NEVER store the fan while it is
still plugged in.
4. NEVER wrap the cord tightly
around the fan.
5. DO NOT put any stress on the
cord where it enters the fan, as
it could cause the cord to break.
PROBLEM
• Fan will not oscillate.
SOLUTION
• Push down on the Oscillation
Pin.
If you have tried these trouble-
shooting solutions and still have
trouble, call 1-888-830-1326 (For
CAN: 1-866-268-1936) or visit our
Web site at
HUNTER FAN COMPANY
2500 FRISCO AVENUE
MEMPHIS, TN 38114
7
8
|