Hotpoint Refrigerator FFQ48 User Manual

Instructions for Installation and Use  
Fridge / Freezer  
Model FFQ48  
 
Operating Instructions  
REFRIGERATOR/FREEZER COMBINATION  
Contents  
GB  
Installation, 4  
Positioning and connection  
GB  
Description of the appliance, 6-7  
Control panel  
English,1  
Overall view  
Accessories, 8  
Refrigerator compartment  
Freezer compartment  
Display, 9-10  
Display description  
Using the display  
Start-up and use, 11  
Starting the appliance  
Chiller system  
Using the refrigerator to its full potential  
Using the freezer to its full potential  
FFQ48  
Maintenance and care, 12  
Switching the appliance off  
Cleaning the appliance  
Avoiding mould and unpleasant odours  
Replacing the light bulb  
Precautions and tips, 13  
General safety  
Disposal  
Respecting and conserving the environment  
Troubleshooting, 14  
Assistance, 15  
After Sales Service, 18  
Hotpoint Guarantee, 19  
Key Contacts, 20  
 
Installation  
! Before operating your new appliance, please read  
these operating instructions carefully. They contain  
important information for safe use, installation and care  
of the appliance.  
! The manufacturer declines any liability should  
these safety measures not be observed.  
GB  
Connection of the water supply  
To carry this out, use the kit provided which contains all  
the necessary elements for connection to the water  
supply.  
! Please keep these operating instructions for future  
reference. Pass them on to possible new owners of the  
appliance.  
To improve the performance of the Aqua Care, we  
recommend that you fit a tap with a filter on the pipe for  
the connection to the water system: in this way it will be  
possible to manually interrupt the water supply during  
long periods in which Aqua Care is not used.  
! The water pressure inside the water system must be  
between 0.8 bar and 8 bar.  
Positioning and connection  
Positioning  
1. Place the appliance in a well-ventilated humidity-free  
room.  
2. Do not obstruct the rear fan grills. The compressor  
and condenser give off heat and require good ventilation  
to operate correctly and save energy.  
! The appliance must only be connected to a water  
supply suitable for drinking.  
3. Leave a space of at least 10 cm between the top part  
of the appliance and any furniture above it, and at least  
5 cm between the sides and any furniture/side walls.  
4. Ensure the appliance is far away from any sources of  
heat (direct sunlight, electric stove, etc.).  
Your appliance is supplied with a 13amp fused plug that  
can be plugged into a 13amp socket for immediate use.  
Before using the appliance please read the instructions  
below.  
Levelling  
WARNING:  
THIS APPLIANCE MUST BE EARTHED.  
1. Install the appliance on a level and rigid floor.  
2. If the floor is not perfectly horizontal, adjust the  
refrigerator by tightening or loosening the rear feet.  
Replacing fuse covers:  
Electrical connections  
When replacing a faulty fuse, a 13amp ASTA approved  
fuse to BS 1362 should always be used and the fuse  
cover re-fitted.  
If the fuse cover is lost, the plug must not be used until  
a replacement is obtained.  
After transportation of the appliance, carefully place it  
vertically and wait at least 3 hours before connecting it  
to the electricity mains. Before inserting the plug into the  
electrical socket ensure the following:  
• The appliance is earthed and the plug is compliant  
with the law.  
• The socket can withstand the maximum power of the  
appliance, which is indicated on the data plate  
located on the bottom left side of the fridge (e.g. 150  
W).  
Replacement fuse covers:  
If a replacement fuse cover is fitted, it must be of the  
correct colour as indicated by the coloured marking or the  
colour that is embossed in words on the base of the plug.  
• The voltage must be in the range between the values  
indicated on the data plate located on the bottom left  
side (e.g. 220-240V).  
Changing the plug:  
• The socket is compatible with the plug of the  
Removing the plug  
appliance.  
If your appliance has a non-rewireable moulded plug  
and you should wish to remove it to add a longer cable  
or to re-route the mains cable through partitions, units  
etc. please ensure that either:  
If the socket is incompatible with the plug, ask an  
authorised technician to replace it (see Assistance).  
Do not use extension cords or multiple sockets.  
-
The plug is replaced by a fused 13amp re-  
wireable plug bearing the BSI mark of  
approval.  
! Once the appliance has been installed, the power  
supply cable and the electrical socket must be easily  
accessible.  
or  
-
The mains cable is wired directly into a  
13amp cable outlet, controlled by a  
switch (in compliance with BS 5733)  
which is accessible without moving the  
appliance.  
! The cable must not be bent or compressed.  
! The cable must be checked regularly and replaced by  
authorised technicians only (see Assistance).  
4
 
Aqua Care function  
Disposing of the plug  
GB  
Cut off and dispose of the supplied plug if it does not fit  
your socket. The cable should be cut as close as  
possible to the moulded plug.  
The refrigerator you have purchased is fitted with the  
Aqua Care system which, thanks to an advanced filter  
system with active carbons, provides your household  
with fresh, filtered water.  
Remove the fuse.  
WARNING:  
! To improve the system’s performance, we recommend  
that you follow the instructions contained in this manual  
and in the assembly diagram provided with the kit.  
To avoid a shock hazard do not insert the discarded  
plug into a socket anywhere else.  
Starting Aqua Care  
Fitting a new plug  
After connecting it to the water system, installing the  
filter (see Replacing Aqua Care filter) and switching on  
the refrigerator (See Starting the appliance), it is  
necessary to remove any air from the Aqua Care system:  
IMPORTANT  
WIRES IN THE MAINS LEAD ARE COLOURED IN  
ACCORDANCE WITH THE FOLLOWING CODE...  
1. Activate the AQUA CARE  
function by pressing the correct  
button (see Display)  
Green and Yellow - Earth  
Blue  
- Neutral  
- Live  
Brown  
2. Place a container under the  
dispenser.  
3. Hold the button down until the  
water is dispensed.  
As the colours of the wires in the mains lead may not  
correspond with the coloured markings identifying the  
terminals in your plug, proceed as follows:  
4. Drain and discard three litres  
of water.  
-
Connect Green and Yellow wire to terminal marked  
'E' or or coloured Green and Yellow.  
-
-
Connect Brown wire to terminal marked 'L' or  
coloured red or brown.  
Connect Blue wire to terminal marked 'N' or  
coloured Black or Blue.  
! When using for the first time and each time the Aqua  
Care system is not used for more than 1 week, it will be  
necessary to drain and discard three litres of water.  
If a 13amp plug (BS 1363) is used it must be  
fitted with a 13amp fuse. A 15amp plug must be  
protected by a 15amp fuse, either in the plug or adaptor  
or at the distribution board.  
If you are in any doubt about the electrical  
supply to your machine, consult a qualified  
electrician before use.  
CE Marking certifies that this appliance conforms to  
the following EEC directives :  
Low Voltage Equipment - 73/23/EEC & 93/68 EEC  
Electromagnetic Compatibility 89/336/EEC, 92/31/EEC  
& 93/68/EEC  
5
 
Description of the  
appliance  
Control panel  
GB  
ON/OFF  
Display  
ADJUST/SELECT +  
MODE  
button  
button  
button  
ECO  
ADJUST/SELECT -  
AQUA  
CARE  
button  
RESET ALARM  
button  
button  
MODE selects the various display settings and  
ON/OFF button switches the whole appliance on and  
off (refrigerator compartment and freezer  
compartment). It must be held down for at least 2  
seconds. See Start-up and use and Maintenance and  
care.  
functions. See Display and Start-up and use.  
ADJUST/SELECT + button activates the functions  
and modifies the temperature, time, date and  
language settings. See Display and Start-up and use.  
AQUA CARE button activates and deactivates the  
ADJUST/SELECT + button deactivates the functions  
and modifies the temperature, time, date and  
Aqua Care function.  
language settings. See Display and Start-up and use.  
RESET ALARM button switches off the sound alarm  
(press once) and deletes the alarm messages from  
the scrolling text on the display (press a second time).  
See Troubleshooting.  
Display programmes the appliance and controls its  
operation. See Display  
6
 
Description of the  
appliance  
Overall view  
GB  
Removable shelf with  
lid and EGG TRAY  
LAMP  
(see Maintenance)  
Storage SHELF  
AQUA CARE tank  
CAN RACK shelves  
SHELVES•  
MULTI-USEbin  
*
AQUA CARE filter  
FRESH BOX  
Compartment  
*
BOTTLE FASTENER  
FRUIT and  
VEGETABLE bin  
BOTTLE shelf  
FREEZER and  
STORAGE  
compartment  
MAX  
MAX  
WATER LEVEL  
WATER LEVEL  
ICE TRAYS  
STORAGE  
compartments  
Levelling FEET  
Varies by number and/or position.  
* Available only on certain models.  
7
 
Accessories  
Refrigerator compartment  
Freezer compartment  
GB  
SHELVES: thanks to the special  
ICE TRAYS: to make ice.  
rails the shelves are removable  
and the height is adjustable (see  
diagram), allowing easy storage  
of large containers and food.  
Height can be adjusted without  
complete removal of the shelf.  
1
1. Pull out the tray by pushing it  
up and then outwards (see  
diagram).  
Check that the tray is completely  
empty and fill it with water through  
the opening provided.  
2
MULTI-USE bin : to store food  
*
(such as cold meats) for a long  
time and also prevent odours  
from lingering in the refrigerator.  
It can be removed for use and it  
may be shifted sideways to  
2. Take care not to exceed the  
level indicated (MAX WATER  
LEVEL). Excess water prevents  
the ice cubes from dispensing (if  
this happens, wait for the ice to  
melt and empty the tray).  
optimise space (see diagram).  
FRESH BOX : for fresh meat and  
3. Turn the tray 90°: the water fills  
up the moulds (see diagram).  
Close the opening with the lid  
and replace. When the ice has  
formed (minimum time  
*
fish. Due to the compartment’s  
low temperature (the coldest in  
the refrigerator), food can be  
stored for up to one week. It can  
also be used for “cold meals.”  
MAX  
WATER LEVEL  
approximately 8 hours), knock the  
tray against a hard surface.  
CAN RACK shelf: to store cans  
horizontally (see diagram). You  
may also store yoghurt, butter or  
general containers.  
ICE PARTY: to bring a bottle of  
sparkling wine or champagne to  
the right temperature. Place it in  
the bucket provided inside the  
FREEZER and STORAGE  
compartment. The bucket may be  
used to serve the bottle, keeping  
it cool.  
ODOUR FILTER*: Some models  
are fitted with a new odour filter  
with active carbons, which  
ensures better air quality inside  
the refrigerator.  
The filter is located on the bottom  
right-hand side, inside the  
ventilation opening. To activate it, remove the sticker  
from the opening (see diagram).  
Varies by number and/or position.  
* Available only on certain models.  
8
 
Display  
Display description  
GB  
ALARM indicator light  
Scrolling text  
REFRIGERATOR OPERATION  
TIME  
indicator light  
AQUA CARE  
indicator light  
indicator light  
ECO  
ICE PARTY functions  
SUPER COOL function  
SUPER FREEZE function  
ECO function  
FREEZER OPERATION  
indicator light  
REFRIGERATOR OPERATION indicator light: displays  
the set temperature (static digit) or the temperature that  
is being set (flashing digit) for the refrigerator  
SUPER COOL function: displays function status. This is  
the rapid cooling function of the refrigerator  
compartment. It deactivates automatically. See Start-up  
and use.  
compartment. OFF indicates that the compartment is off.  
SUPER FREEZE function: displays function status. This  
is the rapid cooling function of the freezer compartment.  
It deactivates automatically. See Start-up and use.  
ALARM indicator light: when this goes on it indicates a  
critical situation (door open, high temperature) See  
Troubleshooting.  
AQUA CARE function: displays function status. It  
supplies fresh, filtered water by means of the dispenser.  
ECO function: displays function status Automatically  
sets the optimal temperature to store food while  
minimizing energy consumption.  
ICE PARTY function: displays function status. It  
reduces the temperature of the freezer for the period of  
time required to cool a bottle.  
TIME indicator light: displays the time. This is also used  
A buzzer sounds when the correct temperature has  
been reached. See Accessories.  
to set the date and time.  
Scrolling text: displays information on the status of the  
appliance and on how to use the display.  
It is also used to set the language.  
! The function symbols light up in various ways to indicate  
their status (deactivated, selected or activated).  
FREEZER OPERATION indicator light: displays the set  
temperature (static digit) or the temperature that is being  
set (flashing digit) for the freezer compartment. OFF  
indicates that the compartment is off.  
9
 
Water dispensing  
Using the display  
GB  
1. Activate the Aqua Care function  
2. Place the container that needs to be filled under the  
outer dispenser.  
3. Press the dispenser  
4. Interrupt the flow by moving the container away from the  
dispenser  
setting the temperature  
When the appliance is switched on, the standard storage  
temperatures are automatically set:  
• +5°C for the refrigerator compartment  
• -18°C for the freezer compartment.  
! The Aqua Care function comes with a safety timer that  
interrupts the supply if operation is continuos for more than  
5 minutes. To restore operation it is necessary to press the  
RESET ALARM button twice.  
The temperatures that may be set are the following:  
• between +2°C and +8°C for the refrigerator  
compartment  
• between -18°C and -26°C for the freezer compartment  
Setting the date and time  
The settings are in series and it is not possible to adjust the  
date if the time has not been set before:  
To set the temperature:  
1. Press the MODE button until the value flashes on the  
refrigerator compartment or freezer compartment display.  
2. To increase the temperature, press the ADJUST/  
SELECT+ button.  
To decrease the temperature, press the ADJUST/SELECT-  
button.  
Each time the button is pressed, the value increases by 1°C.  
3. Confirm the choice by pressing the MODE button within  
ten seconds: the value will stop flashing: If the choice is not  
confirmed, the temperature that had been set before the  
operation will appear on the display.  
1. Press the MODE button repeatedly until the SET TIME  
[+/-] appears on the scrolling text display.  
2. To scroll forward one hour press the ADJUST/SELECT+  
button. To scroll back one hour press the ADJUST/SELECT-  
button.  
3. Confirm the choice by pressing the MODE button within  
ten seconds. If the choice is not confirmed, the time that  
had been set before the operation will appear on the  
display.  
Once the hours have been set, the minutes, days, months  
! The ECO function reduces the possible adjustments: from  
+4°C to +6°C for the refrigerator and from -18°C to -20°C  
for the freezer.  
and years can be set by following steps 1-3.  
Σεττινγ τηε λανγυαγε  
1. Press the MODE button repeatedly until the language  
setting screen appears on the scrolling text display.  
2. To scroll forward, press the ADJUST/SELECT + button.  
To scroll back, press the ADJUST/SELECT - button.  
3. Confirm the choice by pressing the MODE button within  
ten seconds. If the choice is not confirmed, the language  
that had been set before the operation will appear on the  
display.  
Function status  
function activated (green symbol with blue inside on)  
function selected (green symbol with red border  
on)  
! The first time that the appliance is switched on, the  
language setting request screen appears automatically on  
the display: follow the described procedure.  
function deactivated (green symbol only on)  
Activating and deactivating the SUPER COOL,  
ECO, SUPER FREEZE, ICE PARTY functions.  
Σωιτχη οφφ τηε σουνδ ανδ ϖισυαλ αλαρµσ  
Press the RESET ALARM button: by pressing it once, the  
sound alarms are switched off; by pressing it a second  
time, the alarm messages are deleted from the scrolling  
text on the display.  
1. Press the MODE button until the desired function is  
selected.  
2. To activate, press the ADJUST/SELECT + button.  
To deactivate, press the ADJUST/SELECT - button.  
3. Confirm the choice by pressing the MODE button within  
ten seconds. If the choice is not confirmed, the function  
that had been set before the operation will appear on the  
display.  
Once the operation is over, the red border goes off.  
If the function was activated: green symbol with blue inside  
on. If the function was deactivated: green symbol only on.  
! The open door alarm is stopped by closing it (see  
Troubleshooting).  
! If DEMO MODE appears on the display, the appliance is  
in exhibition mode, that is, it does not cool despite the fact  
that the display and the internal lamp are on. To exit this  
mode, press the MODE, ADJUST/SELECT+ and ADJUST/  
SELECT- buttons simultaneously for at least three seconds.  
Activating and deactivating the AQUA CARE function  
1. Press the Aqua Care button. A message on the display  
shows the current status of the function.  
2. Press the Aqua Care button again to activate or  
deactivate the function.  
10  
 
Start-up and use  
Starting the appliance  
Using the refrigerator to its full potential  
GB  
! Before starting the appliance, follow the installation  
instructions (see Installation).  
• Adjust the temperature using the display.  
• Activate the SUPER COOL function to lower the  
temperature quickly. For example, when you place a  
large number of new food items inside a fridge, the  
internal temperature will rise slightly. The function  
quickly cools the groceries by temporarily reducing the  
temperature until it reaches the ideal level.  
! Before connecting the appliance, clean the  
compartments and accessories well with lukewarm  
water and bicarbonate of soda.  
! The appliance comes with a motor protection control  
system which makes the compressor start approximately  
8 minutes after being switched on. The compressor also  
starts each time the power supply is cut off whether  
voluntarily or involuntarily (blackout).  
• Place only cold or lukewarm foods in the compartment,  
not hot foods (see Precautions and tips).  
• Remember that cooked foods do not last longer than  
raw foods.  
Insert the plug into the electrical socket and, if OFF  
appears on both indicator displays (refrigerator and  
freezer), switch on the appliance by holding down the  
ON/OFF button for at least two seconds:  
- the refrigerator is set at a temperature of +5°C.  
- the freezer is set at a temperature of -18°C.  
• Do not store liquids in open containers. They will  
increase humidity in the refrigerator and cause  
condensation to form.  
To cool the two compartments more rapidly, activate the  
SUPER COOL and SUPER FREEZE functions (see  
Display).  
Using the freezer to its full potential  
• Adjust the temperature using the display.  
To freeze a lot of food, activate the SUPER FREEZE  
function. The function is automatically disabled after  
24 hours or once the optimal temperature has been  
reached.  
Chiller system  
The appliance is fitted with the following cooling system:  
No Frost  
It is recognisable by aeration  
cells located on the back walls  
• Do not refreeze food that has been defrosted or that is  
defrosting; this food must be eaten within 24 hours or  
may be frozen again after it has been cooked.  
of the compartments.  
The No Frost system circulates  
cold air continuously to collect  
• Fresh food that needs to be frozen must not come  
into contact with food that has already been  
humidity and prevent ice and  
frost formation. The system  
maintains an optimal humidity level in the compartment,  
preserving the original quality of the food, preventing the  
food from sticking together and making defrosting a  
thing of the past.  
defrosted. Fresh food must be packed in the top  
FREEZER compartment where the temperature drops  
below -18°C and guarantees rapid freezing.  
• Do not place glass bottles which contain liquids, and  
which are corked or hermetically sealed in the freezer  
because they could break.  
! Do not block the aeration cells by placing food or  
containers in direct contact with the refrigerating back  
panel.  
• The maximum quantity of food that may be frozen daily  
is indicated on the plate containing the technical  
properties located on the bottom left side of the  
refrigerator compartment (for example: Kg/24h 4).  
! Close bottles and wrap food tightly.  
! Do not open the door during freezing.  
! If there is a power cut or malfunction, do not open the  
freezer door. This will help maintain the temperature  
inside the freezer, ensuring that foods are conserved for  
at least 9 -14 hours.  
11  
 
Maintenance and care  
Switching the appliance off  
depending on the type of food that is stored. For  
GB  
information on where a replacement filter may be  
purchased, contact Assistance (see Assistance). To  
replace the filter, follow the instructions (see diagrams  
A and B).  
During cleaning and maintenance it is necessary to  
disconnect the appliance from the electricity supply:  
1. hold the ON/OFF button down for more than two  
seconds until OFF appears on both indicator displays  
(refrigerator and freezer).  
A
2. pull the plug out of the socket  
!
If this procedure is not followed, the alarm may sound.  
This alarm does not indicate a malfunction. To restore  
normal operation, it is sufficient to hold the ON/OFF  
button down for more than two seconds. To disconnect  
the appliance, follow points 1 and 2.  
B
Cleaning the appliance  
Replacing the Aqua Care filter  
• The external and internal parts, as well as the rubber  
seals may be cleaned using a sponge that has been  
soaked in lukewarm water and bicarbonate of soda or  
neutral soap. Do not use solvents, abrasive products,  
bleach or ammonia.  
• The removable accessories may be soaked in warm  
water and soap or dishwashing liquid. Rinse and dry  
them carefully.  
• The back of the appliance may collect dust which can  
be removed by delicately using the hose of a vacuum  
cleaner set on medium power. The appliance must be  
switched off and the plug must be pulled out before  
cleaning the appliance.  
The Aqua Care system is fitted with an internal meter  
which guarantees filtering safety. The filter is guaranteed  
for a maximum volume of 1500 l of water, although this  
may vary according to the condition and pressure of the  
water supply. Once this limit has been reached, the  
water supply will stop, the corresponding alarms are  
activated (see Troubleshooting) and the filter must be  
replaced.  
! The filter must always be replaced 6 months after it has  
been installed.  
! If the filter is replaced without an alarm going off  
indicating that the filter is worn out, before replacing it  
press the ADJUST/SELECT+ and ADJUST/SELECT-  
buttons for ten seconds until a message appears on the  
display.  
Avoiding mould and unpleasant odours  
• The appliance is manufactured with hygienic  
materials which are odour free. In order to maintain an  
odour free refrigerator and to prevent the formation of  
stains, food must always be covered or sealed  
properly.  
Replacing the filter:  
1. Deactivate the Aqua Care function (see Display)  
2. Unscrew the filter, turning it in an anticlockwise  
direction (1/4 turn)  
• If you want to switch the appliance off for an extended  
period of time, clean the inside and leave the doors  
open.  
3. After removing the red cap, screw on the new filter by  
turning it in a clockwise direction (1/4 turn)  
4. Press the RESET ALARM button for approximately  
three seconds if the filter alarm has activated (see  
Troubleshooting)  
Replacing the light bulb  
5. Activate the Aqua Care function (see Display)  
! IOnce the filter has been changed, the message  
“Warning - change filter” may appear on the display. This  
is a normal system function.  
To replace the light bulb in the refrigerator compartment,  
pull out the plug from the  
electrical socket.  
Access the light bulb as shown  
(see diagram) and replace it  
with a similar light bulb, the  
power of which should not  
exceed 10 W.  
90˚  
Replacing the l Odour filter  
90˚  
The filter should be replaced after approximately 6-8  
months from when it is activated. This period may vary  
12  
 
Precautions and tips  
! The appliance was designed and manufactured in  
compliance with international safety standards. The  
following warnings are provided for safety reasons and  
must be read carefully.  
• Do not allow children to tamper with the controls or  
GB  
play with the appliance. Under no circumstance  
should they be allowed to sit on the bins or to hang  
from the door.  
This appliance complies with the following  
Community Directives:  
• Keep packaging material out of the reach of children.  
- 73/23/EEC of 19/02/73 (Low Voltage) and subsequent  
amendments;  
-89/336/EEC of 03.05.89 (Electromagnetic Compatibility)  
and subsequent amendments.  
Disposal  
• Observe local environmental standards when  
disposing of packaging material for recycling  
purposes.  
General safety  
• Observe existing legislation and make use of services  
provided by local authorities, ensuring that the pipes  
are not damaged.  
• The appliance was designed for domestic use inside  
the home and is not intended for commercial or  
industrial use.  
Refrigerants such as isobutane and cyclopentane are  
located in the cooling zones and the isolation system  
of the refrigerator and freezer.  
• The appliance must be used by adults only to store  
and freeze food products according to the  
instructions in this manual.  
• Make the appliance unusable by cutting off the cable  
and remove any door catches before disposal.  
• The appliance must not be installed outdoors, even in  
covered areas. It is extremely dangerous to leave the  
appliance exposed to rain and storms.  
Respecting and conserving the  
environment  
• Do not touch the appliance with bare feet or with wet  
or damp hands and feet.  
• Install the appliance in a fresh and well-ventilated  
room. Ensure that it is protected from direct sunlight  
and do not place it near heat sources.  
• Do not touch the internal cooling elements: this could  
cause skin abrasions or frost/freezer burns.  
• Try to avoid keeping the door open for long periods  
or opening the door too frequently in order to  
conserve energy.  
• When unplugging the appliance always pull the plug  
from the mains socket, do not pull on the cable.  
• Before cleaning and maintenance, always switch off  
the appliance and disconnect it from the electrical  
supply.  
• Do not fill the appliance with too much food: cold air  
must circulate freely for food to be preserved  
properly. If circulation is impeded, the compressor will  
work continuously.  
It is not sufficient to hold the ON/OFF button down for  
more than two seconds to eliminate all electrical  
contact.  
• Do not place hot food directly into the refrigerator. The  
internal temperature will increase and force the  
compressor to work harder and will consume more  
energy.  
• In the case of a malfunction, under no circumstances  
should you attempt to repair the appliance yourself.  
Repairs carried out by inexperienced persons may  
cause injury or further malfunctioning of the  
appliance.  
• Regularly check the door seals and wipe clean to  
ensure they are free of debris and to prevent cold air  
from escaping (see Maintenance).  
• Do not use devices or tools other than the special  
scraper provided inside the compartments.  
• Do not put ice cubes taken directly from the freezer  
into your mouth.  
13  
 
Troubleshooting  
If the appliance does not work, before calling for Assistance (see Assistance), check for a solution from the following list.  
GB  
Malfunctions:  
Possible causes / Solutions:  
• The plug has not been inserted into the electrical socket, or not far  
enough to make contact, or there is no power in the house.  
The display is completely switched  
off.  
• The appliance comes with a motor protection control (see Start-up and use).  
• Pull out and reverse the plug before putting it back in the socket.  
The motor does not start.  
The display is on but it is dim.  
a) The refrigerator door has remained open for more than two minutes  
The buzzer stops when the door is closed or by pressing the RESET  
ALARM button. or the correct switching-off procedure was not followed  
(see Maintenance).  
a) The alarms goes off and the lamp  
in the refrigerator compartment  
flashes.  
b) The temperature of the freezer is too high.  
b) The alarm goes off and a message  
appears on the scrolling text of the  
display.  
The freezer will maintain a temperature of around 0°C so that the food  
will not refreeze, allowing you to eat it within 24 hours or to freeze it  
again after cooking them.  
c) The temperature of the freezer has reached a dangerous level. the food  
must not be eaten. The freezer will reach a temperature of -18°C.  
To switch off the buzzer, press the RESET ALARM button. Press again to  
delete the message on the display and to restore normal operation.  
c) The alarm goes off and a message  
appears on the scrolling text of the  
display.  
• The Aqua Care filter is about to wear out  
The Aqua Care icon flashes and a  
message appears on the display  
• The Aqua Care filter is worn out and needs to be replaced (see  
Maintenance and care)  
Water supply interrupted with repeated  
buzzer sounding every two hours and  
message appearing on the display  
• The Aqua Care safety blocking system has been activated due to  
prolonged supply (5 consecutive minutes). Press the Reset Alarm button  
twice (see Display).  
Water supply blocked and message  
appearing on the display  
• The doors do not close properly or the seals are damaged.  
• The doors are opened too frequently.  
• The temperature that has been set is too high (see Start-up and use).  
• The refrigerator or the freezer have been over-filled.  
The refrigerator and the freezer do  
not cool well.  
• The temperature that has been set is too low (see Start-up and use).  
The food inside the refrigerator is  
beginning to freeze.  
• The SUPER COOL and/or SUPER FREEZE and/or ICE PARTY functions  
are active.  
The motor runs continuously.  
• The door is not closed properly or is continuously opened.  
• The outside ambient temperature is very high.  
• The appliance has not been installed on a level surface (see  
Installation).  
The appliance makes a lot of noise.  
• The appliance has been installed between cabinets that vibrate and  
make noise.  
• The internal refrigerant makes a slight noise even when the compressor  
is off. This is not a defect, it is normal.  
• Electrical disturbance on the network or brief interruptions of the power supply  
Early ending of functions  
Normal system function  
After the filter has been changed, the  
message “Warning - change filter”  
appears on the display.  
14  
 
Assistance  
195000000.00  
10/2004  
Before calling for Assistance:  
GB  
Check if the malfunction can be solved on your own (see Troubleshooting).  
• If the appliance is still not working and the problem persists despite having carried out all the checks, call  
your nearest Service Centre.  
model  
serial number  
Communicating:  
• type of malfunction  
• appliance model (Mod.)  
• serial number (S/N)  
This information can be found on the data plate  
located on the bottom left side of the refrigerator  
compartment.  
TI  
93139180000  
Cod.  
S/N 704211801  
Mod. RG 2330  
220 - 240 V-  
Fuse  
A
Max 15 w  
50 Hz 150 W  
W
Class  
Freez. Capac  
340  
75  
Total  
Net  
Gross  
Bruto  
Brut  
Gross  
Bruto  
Brut  
Gross  
Bruto  
Brut  
Poder de Cong Clase  
N
Util  
Classe  
kg/24 h 4,0  
Utile  
Pressure  
HIGH-235  
LOW 140  
Compr.  
Syst.  
Test  
R
134 a  
P.S-I.  
kg 0,090  
Kompr.  
Made in Italy 13918  
Never use unauthorized technicians and never accept replacement parts that are not original  
15  
 
Notes  
GB  
16  
 
Notes  
GB  
17  
 
After Sales Service  
GB  
"No company is better positioned to offer an after sales service on a  
Hotpoint appliance than us - the manufacturer"  
As part of our commitment to you, all Hotpoint appliances have the added benefit of a fully inclusive parts  
and labour guarantee for the first 12 months. In addition to this you also have the advantage of free  
replacement parts for the first 5 years when fitted by a Hotpoint  
engineer. When the 12 months parts and labour guarantee expires we offer the following after sales  
service options:  
Repair Service and Information Help Desk  
UK: 08709 066066  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the Model number and the Serial number of your appliance  
Available 364 days a year with a fast, effective and value for money service. We have the largest white  
goods repair service in the UK with over 1200 of our own fully trained engineers. All repairs include a  
parts and labour guarantee for 12 months from the date of the repair.  
If you require any information or have any questions about your appliance, our operators are on hand with  
help and advice.  
All this ensures that you will receive the best available after sales service possible.  
Extended Warranties  
UK: 08709 088 088  
Republic of Ireland: 1850 502 200  
Whether you have just one or a number of Hotpoint appliances in your kitchen, we offer two service cover  
plans to give you total peace of mind.  
- Repair Protection Plan  
period  
-
FREE service repairs for a single Hotpoint appliance during the  
of cover.  
- Kitchen Cover  
-
FREE service repairs for all your Hotpoint appliances less than 8  
years old.  
Genuine Parts and AccessoriesUK: 08709 077 077  
Republic of Ireland: (01) 842 6836  
A wide range of genuine parts and accessories are available from our hotline or through our web site.  
Genuine parts and accessories, extended warranties and service repairs are all  
available on our web-site at:  
18  
 
GB  
Guarantee  
"Satisfaction guaranteed or your money back"  
We give you a unique 'satisfaction guaranteed' promise - valid for 90 days - after you have  
purchased your Hotpoint appliance. If there is a technical problem simply call Hotpoint Repair service  
engineer to call. If the technical problem is not resolved under this guarantee, we will replace your  
machine or, if you prefer, give you your money back.  
All Hotpoint appliances carry a fully inclusive 12 month parts and labour guarantee as well as free  
replacement parts for the first 5 years (except microwaves, selected integrated appliances and cooker  
hoods, which have a one year guarantee) provided that they are fitted by a Hotpoint engineer.  
Guarantee terms and conditions  
Your guarantee is only applicable in the United Kingdom or Republic of Ireland and is subject to the  
following provisions that your appliance:  
-
-
Has been installed and used correctly in accordance with this instruction booklet.  
Has been used solely for domestic purposes and is located on domestic premises (ie. not for  
commercial or trade use).  
-
Has been properly connected to a suitable electrical supply voltage as stated on the appliance  
rating plate.  
-
Has not been subject to misuse, accident, modified or repaired by anyone other than one of our  
own service engineers.  
For pre purchase information on any other Hotpoint product call: 08701 50 60 70  
Recycling & Disposal Information  
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to  
use quality recycled components to keep down customer costs and minimise material wastage.  
Please dispose of packaging and old appliances carefully.  
To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the  
appliance. Dispose of these parts separately to ensure that the appliance can no longer be plugged  
into a mains socket, and the door cannot be locked shut.  
19  
 
Key Contacts  
After Sales Service  
Over 1200 trained specialists, directly employed by us, ensure that you can have complete confidence in  
both the appliances and services we offer.  
Repair Service and Information Desk  
UK: 08709 066 066  
(Open 8 to 8 Mon - Fri, 8 to 6 Sat, 10 to 4 Sun & Bank Holidays)  
Republic of Ireland: 1850 302 200  
Note: Our operators will require the following information:  
Model number:  
Serial number:  
Extended Warranties  
UK: 08709 088 088  
(Open 8 to 8 Mon - Sun)  
Republic of Ireland: 1850 502 200  
Genuine Parts and Accessories  
UK: 08709 077 077  
(Open 8-30 to 5-30 Mon - Fri & 9 to 12 Sat)  
Republic of Ireland: (01) 842 6836  
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB.  
November 2004  
195.0481.03.00  
 

Graco Car Seat PD250304A User Manual
Graco Home Theater Server 243066 Series A User Manual
Hamilton Beach Microwave Oven 87176 User Manual
Heath Zenith Landscape Lighting 2LBL7 User Manual
Honeywell Humidifier HE365A User Manual
HP Hewlett Packard Welder AXCRN3 2G User Manual
Huffy Fitness Equipment 211573011 User Manual
Hypertec Mouse HKBMONUBWED User Manual
ICP DAS USA Network Card 8430 User Manual
iHome Portable Stereo System IP97 User Manual