Hotpoint Oven SE481012X User Manual

Operating Instructions

OVEN

Contents

Installation, 2-3

Positioning

English, 1

Electrical connection, 4

Data plate

Description of the appliance, 5

Overall view of classical-opening model

Overall view of side-opening model

Control panel

Start-up and use, 6-7

Control panel lock

DEMO mode

Setting the clock

Setting the timer

Starting the oven

SE481012X

SE48L1012X

SE48R1012X

Cooking modes, 8-11

Manual cooking modes

Automatic cooking modes

Programming cooking

Practical cooking advice

Cooking advice table

Precautions and tips, 12

General safety

Disposal

Respecting and conserving the environment

Care and maintenance, 13-14

Switching the appliance off

Cleaning the appliance

Cleaning the oven door

Replacing the light bulb

Assembling the sliding rack kit

Assistance

After Sales Service, 15

Repair Service and Information Desk

Extended Warranties

Genuine Parts and Accessories

Guarantee, 16

16 mm thick: use the second

groove (see diagram).

Secure the appliance to the cabinet by opening the

oven door and inserting 4 screws into the 4 holes on

the outer frame.

! All parts which ensure the safe operation of the

appliance must not be removable without the aid of

a tool.

Electrical Connection

Electrical connection

Power cable supply connection to the electrical

mains:

The electrical connection to the mains must be made

on the appliance. The power voltage and frequency

are as indicated on the rating plate.

We recommend you use a power supply cable which

is long enough to allow you to take the oven out of

its recess in the event of maintenance operations

(only use HAR - H 05 - RRF quality cables fitted with

a plug conforming to the regulations in force.

The plug must be accessible at all times.

! THIS APPLIANCE MUST BE EARTHED.

Connecting the power supply cable

Unplug the appliance before all operations, even

when replacing the oven lamp.

To open the terminal board:

• Using a screwdriver, press on the tabs situated

on each side of the terminal board cover.

Using the appliance without correct earthing is

highly dangerous.

• Pull open the terminal board cover.

! After connecting the appliance to the flexible

cable, tighten all the screws on the terminal

board.

To connect the power supply cable, proceed as

follows:

• Unscrew the cable clamp screw and the contact

screws L-N-6.

• Fasten the wires beneath the screwheads using

the following colour scheme: Blue (N) Brown (L)

Yellow-Green 6

TABLE OF CHARACTERISTICS

width 43.5 cm

height 32 cm

depth 41.5 cm

58 l

• Fasten the power supply cable in the

corresponding cable clamp and close the cover.

Dimensions *

Volume *

voltage: 220-240V ~ 50/60Hz

maximum power absorbed

2800 W

Electrical Connection:

Electrical

connections

Voltage Frequency: 230

V-1+N 50Hz

Fuse Section: 16A

Directive 2002/40/EC on the

label of electric ovens.

Regulation EN 50304

Supply cable:

3x1.5mm²

ENERGY LABEL *

Declared energy

consumption for Forced

convection Class

– heating mode:

Gratin

This appliance conforms to

the following European

Economic Community

directives: 73/23/EEC dated

19/02/73 (Low Voltage) and

subsequent amendments -

89/336/EEC dated 03/05/89

(Electromagnetic

You can connect your oven to the system means of

a terminal board. Refer to above information for the

minimal cable sections and the calibration of the

protective elements according to the connection.

If the appliance is installed with a junction box, an

omnipolar circuit breaker - with a minimum contact

opening of 3mm - should be installed between the

appliance and the mains.

Compatibility) and

subsequent amendments -

93/68/EEC dated 22/07/93

and subsequent

amendments.

2002/96/EEC

* Without removable guide rails

Description

of the appliance

Overall view of classical-opening model

GUIDE RAILS

for the sliding racks

position 5

position 4

position 3

position 2

position 1

GRILL rack

DRIPPING PAN rack

Control panel

Overall view of side-opening model

GRILL

rack

GUIDE RAILS

for the sliding

racks

position 5

position 4

position 3

position 2

position 1

Control panel

DRIPPING PAN

rack

Control panel

DURATION

icon

COOKING END TIME

icon

MANUAL

COOKING

MODE

MANUAL

COOKING

MODE

TEMPERATURE

display

TIME

display

selector

icons

TIME SETTING

button

CONTROL PANEL

POWER

button

START / STOP

TIME ADJUSTMENT

buttons

TEMPERATURE

adjustment

LIGHT

button

START

icon

AUTOMATIC

COOKING MODE

selector

AUTOMATIC

COOKING

MODE

icons

TIMER

icon

CLOCK

icon

Start-up and use

! The first time you use your appliance, heat the empty

oven with its door closed at its maximum temperature

for at least half an hour. Ensure that the room is well

ventilated before switching the oven off and opening

the oven door. The appliance may emit a slightly

unpleasant odour caused by protective substances

used during the manufacturing process burning away.

icon and the two digits on the TIME display flash.

2. Press the “+” and “-” buttons to adjust the hours.

3. Press the

button.

4. Press the “+” and “-” buttons to adjust the minutes.

5. Press the

button again to confirm.

Setting the timer

! This may be set while the oven is switched off or

! The “Control panel lock” and “DEMO mode” can be

activated/deactivated even when the control panel is

switched off.

while it is switched on.

! If no button is pressed within 2 minutes of the oven

being switched on, the appliance will be switched

off automatically.

1. Press the

button several times until the

icon and the three digits on the TIME display flash.

2. Press the “+” and “-” buttons to adjust the

minutes;

Control panel lock

To lock the oven controls, press the

3. Press the

button again to confirm.

button, the

“START/STOP” button and the time “+” button on the

right hand side of the control panel in sequence. A

buzzer sounds and the TEMPERATURE display

shows “Loc”.

Switching the oven on

Press the

button to switch the oven on or off.

Starting the oven

To unlock the oven controls, press the

button

and the time “-” button on the right hand side of the

control panel in sequence.

Press the

button to select the desired manual

cooking mode. The cooking temperature and

duration may be set.

The control panel lock function can be activated

when a cooking programme is in progress or when

the oven is switched off, or when a cooking end time

has been set and the start button pressed. The

control panel lock function can also be deactivated

in all the above situations and after the oven has

completed the set cooking programme.

Press the

button to select the desired automatic

cooking mode. The cooking temperature and

duration are both set to default values. The duration

may be modified by ±5/10 minutes, depending on

the selected cooking mode. The text “In” which

appears on the TEMPERATURE display stands for

“place the food IN the oven”. A delayed cooking

cycle may be programmed.

Demo mode

The oven can operate in DEMO mode: all heating

elements are deactivated, and controls remain operative.

To deactivate the DEMO mode, while the oven is

switched on press the ON/OFF button, the START/

STOP button and the time "+" button on the right

hand side of the control panel, in that order.

To deactivate the DEMO mode, while the oven is

switched on press the ON/OFF button and the time

“-” button on the right hand side of the control panel.

A buzzer sounds and the time display shows “D off”.

The DEMO mode can only be activated when the

oven is switched on and no cooking programme has

been commenced.

Begin cooking by pressing the “START/STOP”

button. The oven will begin its preheating stage, and

the current preheating temperature indicator lights

illuminate when this stage is complete. The

temperature of the manual cooking modes may be

adjusted by pressing the “+” and “-” buttons on the

left hand side of the control panel.

When the preheating stage is complete, a buzzer

sounds and all current preheating temperature

indicator lights are illuminated: place the food in the

oven.

During cooking it is always possible to:

Setting the clock

- Change the temperature by pressing the “+” and “-

” buttons on the left hand side of the control panel

(manual cooking modes only).

! The clock may be set when the oven is switched off

or when it is switched on, provided that a delayed

cooking cycle has not been programmed previously.

- Interrupt cooking while maintaining the set duration

by pressing the START/STOP button.

1. Press the

button several times until the

- Press the

button to stop cooking.

- Set a new cooking mode (previous settings will be

reset).

If a blackout occurs while the oven is already in

operation, an automatic system within the appliance

will reactivate the cooking mode from where it was

interrupted as long as the temperature has not

dropped below a certain level. Programmed cooking

modes which have not started will not be restored

and must be reprogrammed.

! There is no preheating stage for the BARBECUE

mode.

! Never put objects directly on the bottom of the

oven; this will avoid the enamel coating being

damaged.

! Always place cookware on the rack(s) provided.

Cooling ventilation

In order to cool down the external temperature of the

oven, a cooling fan generates a stream of air which

escapes between the oven control panel and the

oven door.

! Once the cooking has been completed, the cooling

fan continues to operate until the oven has cooled

down sufficiently.

Oven light

When the oven is not in operation, the lamp can be

switched on at any time by pressing the button.

Cooking modes

Manual cooking modes

Spit roast (only available in certain models)

To operate the rotisserie

spit (see diagram)

! All cooking modes have a default cooking

temperature which may be adjusted manually

between 40°C and 250°C as desired.

proceed as follows:

In the BARBECUE mode, the default power level

value is indicated as a percentage (%) and may also

be adjusted manually.

MULTILEVEL mode

All heating elements and the fan are activated. Since the

heat remains constant throughout the oven, the air cooks

and browns food in a uniform manner. A maximum of two

racks may be used at the same time.

1. Place the dripping pan in position 1.

2. Place the rotisserie support in position 3 and

insert the spit into the hole provided on the back

panel of the oven.

3. Start the spit roast function by selecting the

BARBECUE mode

modes.

The top heating element and the rotisserie spit (where

present) are activated. By pressing the “+” and “-”

buttons on the left hand side of the control panel,

the power levels that may be set will appear on the

TEMPERATURE display; these range between 5%

and 100%. The high and direct temperature of the grill is

recommended for food which requires a high surface

temperature. Always cook in this mode with the oven door

closed.

! When the

mode is activated, the rotisserie spit

will stop if the door is opened.

Automatic cooking modes

! The temperature and cooking duration are pre-set

values, guaranteeing a perfect result every time -

automatically. These values are set using the C.O.P.^®

(Programmed Optimal Cooking) system. The

duration may be modified by ±5/10 minutes,

GRATIN mode

The top heating element and the rotisserie spit

(where present) are activated and the fan begins to

operate. During part of the cycle the circular heating

element is also activated. This combination of

features increases the effectiveness of the

unidirectional thermal radiation of the heating

elements through forced circulation of the air

throughout the oven.

depending on the selected cooking mode. The

cooking cycle stops automatically and the oven

indicates when the dish is cooked. You may start

cooking whether the oven has been preheated or not.

! When the cooking stage has been reached, the oven

buzzer sounds.

This helps prevent food from burning on the surface

and allows the heat to penetrate right into the food.

Always cook in this mode with the oven door closed.

! Do not open the oven door to avoid offsetting the

cooking time and temperature.

LOW TEMPERATURE modes

ROAST mode

This type of cooking can be used for proving, defrosting,

preparing yoghurt and heating dishes at the required

speed. The temperature options are: 40, 65, 90 °C.

Use this function to cook beef, pork and lamb. Place

the meat inside the oven while it is still cold. The

dish may also be placed in a preheated oven.

BAKED CAKES mode

This function is ideal for cooking desserts which are

made using natural yeast, baking powder and

desserts which contain no yeast. Place the dish in

the oven while it is still cold. The dish may also be

placed in a preheated oven.

PIZZA mode

BREAD mode

Use this function to make pizza. Please see the following

chapter for the recipe and further details.

To obtain the best results, we recommend that you

carefully observe the instructions below:

• Follow the recipe.

• Do not exceed the maximum weight of the

dripping pan.

BREAD mode

Use this function to make bread. Please see the following

chapter for the recipe and further details.

• Remember to pour 100 ml of cold water into

the baking tray in position 5.

• The dough must be left to rise at room temperature

for 1 – 1 ½ hours (depending on the room

temperature) or until the dough has doubled in size.

PIZZA mode

To obtain the best results, we recommend that you

carefully observe the instructions below:

• Follow the recipe.

Recipe for BREAD:

1 Dripping pan holding 1000 g Max, lower level

2 Dripping pans each holding 1000 g Max, medium and

lower levels

• The weight of the dough should be between 500 g

and 700 g.

• Lightly grease the dripping pan.

Recipe for 1000 g of dough: 600 g flour, 360 g water, 11g

salt, 25 g fresh yeast (or 2 sachets of powder yeast)

Method:

Recipe for PIZZA:

1 dripping pan on a low shelf level, hot or cold oven

Recipe for 3 pizzas weighing approximately 550 g: 1000

g flour, 500 ml water, 20 g salt, 20 g sugar, 100 ml olive

oil, 20 g fresh yeast (or 2 sachets of powder yeast)

• Leavening at room temperature: 1 hour.

• Place inside hot or cold oven.

• Mix flour and salt in a large bowl.

• Dilute yeast in lukewarm water (approximately 35

degrees).

• Make a small well in the mound of flour.

• Pour in water and yeast mixture.

• Start the

PIZZA cooking mode.

• Knead dough by stretching and folding it over

itself with the palm of your hand for 10 minutes

until it has a uniform consistency and is not too

sticky.

• Ball and cover the dough with plastic wrap and

leave it to leaven at room temperature for 1 – 1 ½

hours (until it has doubled in size).

• Cut the dough into equal sized loaves.

• Place them in the dripping pan on oven paper.

• Cover the loaves with flour.

• Make incisions on the loaves.

• Remember to pour 100 ml of cold water into

the baking tray in position 5. For cleaning

purposes, we recommend the use of water and

vinegar.

• Place the loaves inside the oven while it is still cold.

• Start the

BREAD cooking mode.

• Once baked, leave the loaves on one of the grill racks

until they have cooled completely.

Programming cooking

Practical cooking advice

! A cooking mode must be selected before

! Do not place racks in position 1 and 5 during fan-

assisted cooking. This is because excessive direct

heat can burn temperature sensitive foods.

programming can take place.

Programming the duration

! In the BARBECUE and GRATIN cooking modes,

particularly when using the rotisserie spit, place the

dripping pan in position 1 to collect cooking

residues (fat and/or grease).

To set the duration of a manual cooking mode

1. Press the

button several times until the

icon and the first digit on the TIME display flash.

2. Press the "+" and "-" buttons to adjust the hour

value.

MULTILEVEL

3. Press the

button again until the other two

• Use positions 2 and 4, placing the food which

requires more heat on 2.

digits on the TIME display begin to flash.

4. Press the "+" and "-" buttons to adjust the minute

value.

• Place the dripping pan on the bottom and the rack

on top.

5. Press the

button again to confirm.

• For example: it is 9:00 a.m. and a time of 1 hour

and 15 minutes is programmed. The programme

will stop automatically at 10:15 a.m.

BARBECUE

• Insert the rack in position 3 or 4. Place the food in

the centre of the rack.

Programming delayed cooking

! A cooking duration must be selected before

delayed programming can take place.

• We recommend that the power level is set to

maximum. The top heating element is regulated

by a thermostat and may not always operate

constantly.

1. Follow steps 1 to 5 to set the duration as detailed

above.

PIZZA

2. Then press the

button until the

icon and

the two digits on the TIME display flash.

• Use a light aluminium pizza pan. Place it on the

rack provided.

3. Press the "+" and "-" buttons to adjust the hour

value.

For a crispy crust, do not use the dripping pan as

it prevents the crust from forming by extending

the total cooking time.

4. Press the

button again until the other two

digits on the TIME display begin to flash.

5. Press the "+" and "-" buttons to adjust the minute

value.

• If the pizza has a lot of toppings, we recommend

adding the mozzarella cheese on top of the pizza

halfway through the cooking process.

6. Press the

button again to confirm.

• For example: it is 9:00 a.m. and a time of 1 hour

and 15 minutes is programmed and the end time

is set to 12:30. The programme will start

automatically at 11:15 a.m.

Programming has been set when the

and

buttons are illuminated. The TIME display shows the

cooking end time and the cooking duration alternately.

To cancel a programmed procedure press the

“START/STOP” button.

Cooking advice table

Cooking

modes

Foods

Weight

(in kg)

Rack position

Preheating

Recommended

temperature

(°C)

Cooking duration

(minutes)

standard

guide rails

sliding guide

rails

Multilevel*

Barbecue*

Gratin*

Pizza on 2 racks

Pies on two racks/cakes on 2 racks

Sponge cake on 2 racks (on the dripping pan)

Roast chicken + potatoes

Lamb

Mackerel

Lasagne

Cream puffs on 2 racks

Biscuits on 2 racks

Cheese puffs on 2 racks

Savoury pies

Mackerel

Sole and cuttlefish

Squid and prawn kebabs

Cod fillet

Grilled vegetables

1+1

2 and 4

1 and 2/3

1 or 2

2 and 4

1 and 3

3 or 4

1 and 3

Yes

220-230

180

170

200-210

190-200

180

190-200

190

210

200

20-25

30-35

20-25

65-75

45-50

30-35

35-40

20-25

10-20

20-25

20-30

15-20

10-15

8-10

10-15

15-20

10-12

3-5

70-80

55-60

30-35

70-80

60-70

60-75

70-80

40-45

0.7

0.5

0.8

0.7

4 or 5

4 or 6

100%

210

200

210

2 or 3

Veal steak

Sausages

Hamburgers

Toasted sandwiches (or toast)

Spit-roast chicken using rotisserie spit (where present)

Spit-roast lamb using rotisserie spit (where present)

Grilled chicken

Cuttlefish

Spit-roast chicken using rotisserie spit (where present)

Spit-roast duck using rotisserie spit (where present)

Roast veal or beef

Roast pork

Lamb

1.5

Low

temperature

Defrosting

Proving

Dish heating

Pasteurisation

Pizza (see recipe)

Focaccia (bread dough)

Bread (see recipe)

2 or 3

60-90

Automatic

pizza

23-33

Automatic

bread

Automatic

baked cakes

Automatic

roast

Cakes made using leavened dough

Roasts

2 or 3

35-55

60-80

* The cooking times listed above are intended as guidelines only and may be modified according to personal tastes. Oven preheating times are set as standard and may not be

modified manually.

Precautions and tips

! This appliance has been designed and

• If the appliance breaks down, under no

circumstances should you attempt to perform the

repairs yourself. Repairs carried out by

inexperienced persons may cause injury or further

malfunctioning of the appliance. Contact a Service

Centre (see Assistance).

manufactured in compliance with international safety

standards. The following warnings are provided for

safety reasons and must be read carefully.

General safety

• The appliance was designed for domestic use

inside the home and is not intended for

commercial or industrial use.

• Do not rest heavy objects on the open oven door.

Disposal

• The appliance must not be installed outdoors, even

in covered areas. It is extremely dangerous to

leave the appliance exposed to rain and storms.

• When disposing of packaging material: observe

local legislation so that the packaging may be

reused.

• When moving or positioning the appliance, always

use the handles provided on the sides of the oven.

• The European Directive 2002/96/EC relating to

Waste Electrical and Electronic Equipment

(WEEE) states that household appliances should

not be disposed of using the normal solid urban

waste cycle. Exhausted appliances should be

collected separately in order to optimise the cost

of re-using and recycling the materials inside the

machine, while preventing potential damage to

the atmosphere and to public health. The

crossed-out dustbin is marked on all products to

remind the owner of their obligations regarding

separated waste collection.

• Do not touch the appliance with bare feet or with

wet or damp hands and feet.

• The appliance must be used by adults only for the

preparation of food, in accordance with the

instructions provided in this booklet.

• Do not touch the heating elements and parts of

the oven door when the appliance is in use;

these parts become extremely hot. Keep

children well away from the appliance.

For further information relating to the correct

disposal of exhausted household appliances,

owners may contact the public service provided

or their local dealer.

• Ensure that the power supply cables of other

electrical appliances do not come into contact

with the hot parts of the oven.

• The openings used for the ventilation and

dispersion of heat must never be covered.

Respecting and conserving the

environment

• You can help to reduce the peak load of the

electricity supply network companies by using the

oven in the hours between late afternoon and the

early hours of the morning. The cooking mode

programming options, the “delayed cooking”

mode (see Cooking modes) and “delayed

automatic cleaning” mode (see Care and

Maintenance) in particular, enable the user to

organise their time efficiently.

• Always grip the oven door handle in the centre:

the ends may be hot.

• Always use oven gloves when placing cookware

in the oven or when removing it.

• Do not use aluminium foil to line the bottom of the

oven.

• Do not place flammable materials in the oven: If

the appliance is switched on accidentally, it could

catch fire.

• Always keep the oven door closed when using the

BARBECUE and GRATIN modes: This will achieve

improved results while saving energy

(approximately 10%).

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Check the door seals regularly and wipe them

clean to ensure they are free of debris so that

they adhere properly to the door, thus avoiding

heat dispersion.

• Never perform any cleaning or maintenance work

without having disconnected the appliance from

the electricity mains.

Care and maintenance

Switching the appliance off

Replace the glass panel by following the above

sequence in reverse.

Disconnect your appliance from the electricity

supply before carrying out any work on it.

Replacing the light bulb

To replace the

oven light bulb:

Cleaning the appliance

• The stainless-steel or enamel-coated external

parts and the rubber seals may be cleaned using

a sponge that has been soaked in lukewarm water

and neutral soap. Use specialised products for

the removal of stubborn stains. After cleaning,

rinse and dry thoroughly. Do not use abrasive

powders or corrosive substances.

• The inside of the oven should ideally be cleaned

after each use, while it is still lukewarm. Use hot

water and detergent, then rinse well and dry with

a soft cloth. Do not use abrasive products.

• All accessories - with the exception of the sliding

racks - can be washed like everyday crockery,

and are even dishwasher safe.

1. Remove the glass cover using a screwdriver.

2. Remove the light bulb and replace it with a similar

one: Wattage 15 W, cap E 14.

Replace the glass cover, making sure the seal is

positioned correctly (see diagram).

• We recommend that detergents are not sprayed

directly onto the control panel, but that a sponge

is used instead.

! Never use steam cleaners or pressure cleaners on

the appliance.

Inspecting the seals

Check the door seals around the oven regularly. If

the seals are damaged, please contact your nearest

After-sales Service Centre (see Assistance). We

recommend that the oven is not used until the seals

have been replaced.

Cleaning the oven door*

Clean the glass part of the oven door using a

sponge and a non-abrasive cleaning product, then

dry thoroughly with a soft cloth. Do not use rough

abrasive material or sharp metal scrapers as these

could scratch the surface and cause the glass to

crack.

For more thorough cleaning purposes, the external

glass panel on the oven door may be removed:

1. loosen the two screws V (see figure);

2. remove the glass panel by unhooking it from the

handle (see figure);

Only available on certain models.

Sliding rack kit assembly

To assemble the sliding racks:

Assistance

Warning:

The appliance is fitted with an automatic diagnostic

system which detects any malfunctions.

Malfunctions are displayed by messages of the

following type: “ER” followed by numbers.

Call for technical assistance if a malfunction occurs.

1. Remove the two

frames, lifting them

away from the spacers

A (see figure).

Before calling for Assistance:

• Check whether you can fix the problem yourself.

• Restart the programme to check whether the

malfunction has disappeared.

• If it has not, contact the Authorised Technical

Assistance Service.

2. Choose which shelf

to use with the sliding

rack. Paying attention

to the direction in which

the sliding rack is to be

extracted, position joint

B and then joint C on

the frame.

Left

guide rail

Right guide

rail

! Never use the services of an unauthorised

technician.

Please have the following information to hand:

• The message shown on the TEMPERATURE

display.

• The appliance model (Mod.).

• The serial number (S/N).

3. Secure the two

The latter two pieces of information can be found on

the data plate located on the appliance.

frames with the guide

rails using the holes

provided on the oven

walls (see diagram).

The holes for the left

frame are situated at

the top, while the holes

for the right frame are

at the bottom.

4. Finally, fit the frames on the spacers A.

! Do not place the sliding racks in position 5.

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its working life than

us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and

1100 fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08709 066 066

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08709 077 077

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts

guarantee you must register your appliance with us.

UK: 0870 6092094

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right to use

quality, recycled components to keep down customer costs and minimise material wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,

remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts

separately to ensure that the appliance can no longer be plugged into a mains socket, and the door cannot

be locked shut.

Guarantee

03/2007 - 195060967.00

XEROX BUSINESS SERVICES

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown

repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective because

of either workmanship or materials, we will, at our discretion, either repair or replace the appliance at no

cost to you.

This guarantee is subject to the following conditions:

- The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

The appliance is used only on the electricity or gas supply printed on the rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced become our property.

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on you

registering your appliance with us and the parts being fitted by one of our authorised engineers. There

will be a charge for our engineer's time. To activate the extra parts warranty on your appliance, simply

call our registration line on 0870 6092094 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the expense

of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on 08709

088 088 (ROI 01 230 0233).

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint

Service Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where necessary, to

arrange for an engineer to call. If we cannot resolve the technical problem we will replace your machine

or, if you prefer, give you your money back.

Graco Inc Pressure Washer 2245 User Manual
Greenheck Fan Ventilation Hood ES 30 User Manual
Grundig Flat Panel Television GLCD4000HD GLCD4600HD User Manual
Hamilton Beach Rice Cooker 840106800 User Manual
HannsG Computer Monitor HL195 User Manual
Harbor Freight Tools Saw 03733 User Manual
Hotpoint Clothes Dryer TS13 User Manual
HP Hewlett Packard Computer Accessories 16501A LOGIC User Manual
HP Hewlett Packard Photo Printer 460c User Manual
Hypertec Mouse KYBAC595 USBWHTHY User Manual