Instructions for Installation and Use
6kg Vented Dryer
+
Aquarius
VTD65
VTD60
To the Installer:
Before installation, fill in the product details on the back cover of this
book. The information can be found on the rating plate.
To the User:
You must read these instructions prior to installing and using the
appliance and then retain them for future reference.
Instruction booklet
TUMBLE DRYER
Contents
GB
GB
English
Installation, 2-3
Where to put your dryer
Ventilation
Electrical connection
Before you start using your dryer
Dryer description, 4
The front
The back
Control panel
Start and programmes, 5-7
Choosing a programme
Table of programmes
Option buttons / lights
Display
Door Opening
VTD65
VTD60
Laundry, 8-9
Sorting your laundry
Wash care labels
Special clothing items
Drying times
Warnings and Suggestions, 10
General safety
Disposal
Saving energy and respecting the environment
Maintenance and Care, 11
Switching off the electricity
Cleaning the filter after each cycle
Check the drum after each cycle
Cleaning the dryer
Troubleshooting, 12
Service, 13
Spare parts
! Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you
sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the
new owner may be informed about warnings and suggestions on how the appliance works.
! Read these instructions carefully; the following pages contain important information on installation and suggestions on
how the appliance works.
1
Installation
Permanent venting
Where to put your dryer
GB
In conjunction with the vent tube we recommend
using a Wall/Window Vent Kit, available at a retail
location or the nearest Spare Parts Dealer.
G
Place your dryer at a distance from gas ranges,
stoves, heaters, or cook tops because flames can
damage the appliance.
Minimum gap 10mm
G
If you are going to install the
appliance under a work
Wall mounting
1. Leave an opening in the
wall to the left of the
dryers proposed position.
2. Keep the tube as short
and straight as possible
to prevent condensed
moisture from backing up
into the dryer.
counter, be sure to leave a
10mm space between the
top and any other objects on
or above the machine and a
15mm space between the
sides and lateral furnishings
Minimum gaps
15mm
or walls. This is to ensure
proper air circulation. Make sure that the back
vents are not obstructed.
3. Similarly, the duct in the
wall should slope
G
Make sure you put your dryer in an environment
downwards towards the
outside.
that is not damp and has proper air circulation
throughout. the dryer will not operate efficiently in
an enclosed space or cupboard.
Window mounting
1. With a stacked dryer
the hole in the window
should ideally be made
below the vent.
! We do not recommend that the dryer is installed in a
cupboard but the dryer must never be installed
behind a lockable door, a sliding door or a door with a
hinge on the opposite side to that of the dryer door.
2. The tube should be
kept as short as possible.
Ventilation
The Dryer dries your laundry by drawing in cool, clean
and relatively dry air, heating it, and then distributing
it through the clothes as they are gently tumbled. For
optimum performance, the moist air is then blown out
through a vent tube at the back of the dryer.
Depending on how often you use your dryer, it is
essential that areas A and B are checked periodically
to remove lint or debris.
The vent tube adaptor must be fitted securely thus
preventing any humid air from being emitted back into
the room.
When the dryer is in use, there has to be adequate
ventilation to avoid the back flow of gases into the room
from appliances burning other fuels, including open fires.
! The Dryer should not be pushed so far back that the
tube adaptor is pulled out of position or the tube is
squashed or bent.
Mobile venting
! The tube should be kept clear of the air intake vent
and kinks or ‘U’ bends must be avoided as these will
obstruct the tube or trap condensation.
A vent tube must always be fitted when the dryer is
used in conjunction with Mobile Venting.
The tube must be fitted securely into the back of the
dryer (see Dryer Description). If possible, it is always
best to connect the tube to a permanent
outlet close to the dryer. If permanent installation is
not possible, the dryer will work just as well with the
tube passing through a partly-opened window.
! Ensure that the end of the tube is not directed
toward the air intake vent at the rear of the dryer.
! The vent tube should not exceed 2.4 metres in
length and should be kept free of any possible
accumulation of fluff, lint and water by shaking it out
frequently. Always ensure that the tube is not
squashed.
2
Installation
Open window venting
Changing the plug
GB
The end of the tube
should be directed
downwards, to prevent
warm moist air from
condensing in the room or
in the dryer.
The wires in the power cord are coloured in accordance
with the following:
Inf
m
r
Green and Yellow
(Earth) wire to terminal
tan
marked ‘E’, symbol
,
or coloured green and
yellow.
13A ASTA approved
fuse to BS1362.
Blue (Neutral) wire to
terminal marked ‘N’ or
coloured black.
Brown (Live) wire to
terminal marked ‘L’ or
coloured red.
I
Cord clamp
! Ensure that the dryer is adequately ventilated and
that the end of the vent tube is not directed towards
the air intake duct.
! The vent tube must always be fitted for optimum
performance.
! If the plug being replaced is a non-rewirable type,
then the cut-off plug must be disposed of safely. DO
NOT leave it where it can be inserted into a socket
and create a shock hazard.
! Make sure that the vent tube and air intake vents
are not obstructed or blocked.
! The power supply cord should be checked periodically
and replaced by a cord specially prepared for this
dryer and fitted only by authorised technicians (see
Service). New or longer power cords are supplied at
an extra charge by authorised dealers.
! The dryer must not recycle exhaust air.
! Misusing a tumble dryer may create a fire hazard.
! Do not discharge exhaust air into a flue which is
used for exhaust fumes from other appliances that
burn gas or other fuels.
! The manufacturer denies any responsibility should
any of these rules not be followed.
! If in doubt about any of the above consult a qualified
electrician.
Electrical connections
Make sure of the following before you insert the plug
into the the electrical socket:
Levelling your dryer
G
The socket must be grounded.
G
The socket must be able to sustain the machines
The dryer must be installed level for correct operation.
maximum power, which is indicated on the rating
label (see Dryer Description).
Power voltage must be within the values indicated
on the rating label (see Dryer Description).
The socket must be compatible with the dryers
plug. Should this not be the case, replace the
plug or the socket.
When you have installed
your dryer in its final
location check that it is
level first side to side,
then front to back.
G
G
! The dryer must not be installed outdoors, even if the
space is sheltered. It can be very dangerous if it is
exposed to rain or storms.
! Once installed, the dryers electrical wire and plug
must be within easy reach.
! Do not use extension cords.
! The power cord must not be bent or squashed.
! The power cord supplied is fitted with a BS1363 plug
and a 13 amp BS1362 fuse. If you need to replace the
fuse, use only those rated at 13 amp (13A) and ASTA
approved to BS1362.
If the dryer is not level,
use a wooden block to
support it while adjusting
the two front legs up or
down, until your dryer is
level.
Moulded plug
! The plug must not be used
without the fuse cover in place.
If a replacement fuse holder/cover
is required, it must be of the
same colour coding or wording
as shown on the base of the plug.
Replacements are available from
authorised dealers.
Before you start using your dryer
Once you have installed your dryer and before you use
it, clean the inside of the drum to remove any dust
that could have accumulated during transport.
3
Dryer Description
The front
The back
GB
Control Panel
Drum
Air Intake Vent
Rating plate
Model & Serial
numbers
Vent Tube fitted here
Filter
Caution: Hot!
Control panel
START/CANCEL
On/Off
Light
Button
OPTION
Buttons
Clean Filter Progress
Light
Lights
Indicator
DISPLAY
PROGRAMMES
Knob
ON/OFF
Button
Programme Guide
Option
Lights
Heat
Icons
The START/CANCEL button starts a selected
The On/Off indicator light signals that your dryer is in
programme. When you press this button there will be
one beep and the progress lights will flash to confirm
the action. If you have not set a programme, the
buzzer will beep three times. When a programme is
running, holding this button cancels the programme
and stops the dryer (see Start and Programmes).
use or ready to select a programme.
The ON/OFF button: If the dryer is running and this
button is pressed, the dryer stops. Press again, the
dryer restarts.
The Progress lights show you the status of the
programme. As each stage of the programme starts
the corresponding light turns on.
The OPTION buttons select available options for your
selected programme (see Start and Programmes).
The Option lights indicate that the option to the left
The Heat Icons indicate the heat setting of the selected
of the light has been selected.
programme. High
or Low
.
Does not light if a Wool, Airing or Cool Tumble
programme has been selected.
The Programmes Guide allows you to consult a user
friendly table of the available programmes.
The PROGRAMMES knob sets the programme: rotate
it until the indicator is pointing to the programme you
want to select (see Start and Programmes).
The Clean Filter light gives you a reminder before
every programme that it is essential to clean the
filter every time the dryer is used (see Maintenance and
Care).
4
Start and Programmes
During the drying programme, you can check on
Choosing a programme
GB
your laundry and take out items that are dry
while others continue drying. When you close
the door again, press the START button in order
to resume drying.
1. Plug the dryer into the electrical socket.
2. Sort your laundry according to fabric type (see
Laundry).
Inf
I
r
tan
10. During the last few minutes of Drying
Programmes, before the programme is
completed, the final COOL TUMBLE phase is
entered (fabrics are cooled), this phase should
always be allowed to complete.
3. Open the door and make sure the filter is clean
and in place (see Maintenance).
4. Load the machine and make sure items are not
in the way of the door seal. Close the door.
5. If the On/Off light is not lit: Press the ON/OFF
I
11. The buzzer (if Alarm Option was selected) will
warn you when the programme is complete.
Open the door, take the laundry out, clean the
filter and replace it (see Maintenance).
If the Post Creasecare Option has been selected
and you do not remove the laundry immediately,
the dryer will tumble occasionally for 10 hours
or until you open the door.
button
.
6. Choose a programme by checking the Programmes
Guide (see Programmes) as well as the indications
for each type of fabric (see Laundry).
- Select a programme by rotating the
PROGRAMMES knob clockwise.
7. Set a delay time and other options if necessary.
8. If you wish to select the buzzer sound, at the end
of the programme, press the ALARM Option button.
9. Press the START button to begin. The display will
show the estimated time to end.
12. Unplug the dryer.
Easy Iron Programme
‘Easy Iron’ is a short 10 minute programme (8 minutes of heat followed by a 2 minute cool tumble period) which
fluffs the fibres of clothing that have been left in the same position/location for an extended period of time.
The cycle relaxes the fibres and makes them easier to iron and fold.
! ‘Easy Iron’ is not a drying programme and should not be used for wet articles of clothing.
For best results:
1. Do not load more than the maximum capacity.
These numbers refer to the dry weight:
Fabric
Maximum load
Cotton and Cotton mixtures
Synthetics
2.5kg
2kg
Denim
2kg
2. Unload the dryer immediately after the end of the programme, hang, fold or iron the articles and put
them away in the closet. Should this not be possible repeat the programme.
The ‘Easy Iron’ effect varies from one fabric to the next. It works well on traditional fabrics like Cotton or
Cotton mix, and less well on acrylic fibres and on materials such as Tencel®.
Wool Programme
G
This is a programme for tumble dryer safe garments marked with the symbol
It can be used for load sizes up to 1kg (approximately 3 sweaters).
We recommend that garments are turned inside out before drying.
This programme will take about 20 to 40 minutes, but may take longer depending on the size and density of
the load and the spin speed used in your washer.
.
G
G
G
G
Loads dried using this programme are usually ready to wear, but on some heavier garments the edges
may be slightly damp. Allow these to dry naturally as over-drying could damage garments.
! Unlike other materials, the mechanism of wool shrinkage is irreversible; i.e. it will not stretch back to
original size and shape.
! This programme is not suitable for Acrylic garments.
5
Start and Programmes
Programmes
GB
! If the On/Off light is not lit; Press the ON/OFF button
and then select programme.
What it does...
How to set it...
Note:
Programme
Dries your clothes on
High heat setting, ready
for ironing.
Options available:
1
1. Position the PROGRAMME knob on 1.
2. Select any Options, if required.
3. Press the START button.
Cottons
Alarm, Delayed start,Pre
Creasecare, Post Creasecare.
Ready to Iron
2
Options available:
Dries your clothes on
High heat setting, ready 2. Select any Options, if required.
for hanging.
1. Position the PROGRAMME knob on 2.
Cottons
Alarm, Delayed start,Pre
Creasecare, Post Creasecare.
Hanger Dry
3. Press the START button.
Dries your clothes on High
heat setting, ready for
putting away.
1. Position the PROGRAMME knob on 3.
2. Select any Options, if required.
3. Press the START button.
Options available:
3
Cottons
Alarm, Delayed start,Pre
Creasecare, Post Creasecare.
Cupboard Dry
Options available:
4
Dries your clothes on
High heat setting, ready 2. Select any Options, if required.
for ironing.
1. Position the PROGRAMME knob on 4.
Synthetics
Alarm, Delayed start,Pre
Creasecare, Post Creasecare.
Ready to Iron
3. Press the START button.
Options available:
5
Dries your clothes on
High heat setting, ready 2. Select any Options, if required.
for hanging.
1. Position the PROGRAMME knob on 5.
Synthetics
Alarm, Delayed start,Pre
Creasecare, Post Creasecare.
Hanger Dry
3. Press the START button.
Options available:
6
Dries your clothes on High
heat setting, ready for
putting away.
1. Position the PROGRAMME knob on 6.
2. Select any Options, if required.
3. Press the START button.
Synthetics
Alarm, Delayed start,Pre
Creasecare, Post Creasecare.
Cupboard Dry
Options available:
Dries your clothes on Low 1. Position the PROGRAMME knob on
Alarm, Delayed start, Pre
Creasecare, Post Creasecare.
Delicates
heat setting, ready to be
worn.
2. Select any Options, if required.
3. Press the START button.
(e.g. Acrylics)
Options available:
Dries your Woollen clothes,
1. Position the PROGRAMME knob on
2. Select any Options, if required.
3. Press the START button.
Wool
Alarm
(see previous page).
Airs your clothes with
cool air, use also to cool
warm clothes.
1. Position the PROGRAMME knob on
2. Select any Options, if required.
3. Press the START button.
.
Options available:
AIRING
Alarm
! This is not a drying
programme (see previous
page).
Brief programme
1. Position the PROGRAMME knob on
2. Select any Options, if required.
3. Press the START button.
.
Easy Iron
(approximately 10 minutes)
that softens fibres of
clothing that is ready for
ironing.
Options available:
Alarm
Timed Drying
Options available:
Dries wet clothing that you
wish to dry on low heat or
small loads (less than 1kg).
1. Position the PROGRAMME knob on the
desired time: 120, 90, 60 or 30.
2. Select any Options, if required.
3. Press the START button.
Alarm, High Heat, Delayed
Start, Pre Creasecare, Post
Creasecare.
(120, 90, 60 or
30 minutes)
Can be used with high heat
option if you prefer to use
a timed programme.
Consult suggested drying
times (see Laundry).
The last 10 minutes of these
programmes is the Cool
Tumble.
Options available:
Brief programme
1. Position the PROGRAMME knob on
.
Alarm
(approximately 10 minutes) 2. Select any Options, if required.
that cools fibres of clothing. 3. Press the START button.
Cool Tumble
6
Start and Programmes
The Controls
G
G
PROGRAMMES knob
DISPLAY
GB
! Warning, after pressing the start button, the
programme can not be changed.
! Position 0, turning the knob to position 0 resets and
The display shows either the amount of time delay
remaining or an indication of the amount of time left
for a drying programme.
Inf
I
r
cancels a programme, the display shows
.
The ‘delay time’ is displayed in hours and counts down
each hour.
O8
tan
G
OPTION buttons / lights
The ‘time to end’ is displayed in hours and minutes and
counts down each minute, this includes the cool
tumble phase. When timed programmes are selected
the time displayed throughout the cycle is the actual
time remaining.
When a sensing programme is selected the time
displayed is an estimate of the time remaining. When
the programme is selected the display shows the time
required to dry a full load, after around 10 minutes the
controller calculates a better estimate of the cycle
time.
These buttons are used to customise the selected
programme to your requirements. A programme must
have been selected on the programme knob before an
option can be selected. Not all options are available for
all programmes (see Start and Programmes). If an
option is not available and you press the button, the
buzzer will beep three times. If the option is available
there will be one beep and the option light next to the
button lights to confirm the selection.
I
After the start button has been pressed only the
Alarm, Pre Creasecare and Post Creasecare options
can be changed.
The colons between the hours and minutes in the
display flash to show that the time is counting down.
When the programme finishes its cool tumble phase
Time Delay
The start of some programmes (see Start and
Programmes) can be delayed for up to 18 hours. Press
the display will show
.
E88
this button, the display shows
and the option
The display also shows if there is a problem with your
dryer, if this occurs the display will show F followed by
a fault code number (see Troubleshooting).
OFF
light comes on. Press again and a 1 hour delay is
selected and the display indicates 1hr, each further
press of the button adds 1hr to the delay. When 18hr
G
is displayed a further press the display shows
Door Opening
OFF
and after a couple of seconds cancels the delay. You
can also cancel the delay by turning the programmes
knob to 0, wait for the buzzer to beep and then turn
back to your selected programme.
Opening the door during a programme will stop the
dryer and have the following effects:
G
All 4 progress lights come on.
G
During a delay phase the delay will continue
Pre Creasecare
to count down. The start button must be
pressed to resume the delay programme.
The progress lights will change to show
current status.
This option is only available if a delayed start has been
selected. It tumbles the clothes occasionally during
the delayed period to help prevent creases developing.
High Heat
G
During the drying part of the programme, the
When available this button selects high heat. Press
this button and a high heat setting is selected and
the light alongside the button comes on.
Timed programmes have a default of low heat. If the
light alongside the button is on then pressing the button
selects a low heat setting and the light goes out. The
heat icon on the display will also change.
Alarm
Available on all programmes and allows the buzzer to
give a signal at the end of the drying cycle, to remind
you that the clothes are ready to be removed.
Press the button and the light will show that the
option is selected.
time to end count continues but the colons
do not flash. The start button must be
pressed to resume the programme. The
progress lights will change to show the
current status.
G
During the cool tumble or post creasecare
phase of a drying programme and anytime
during an Airing or Cool Tumble programme,
the programme will finish. Pressing the start
button will re-start a new programme at the
beginning.
G
Changing the programmes knob will select a
new programme, after you press the start
button. You can use this to select the Cool
Tumble programme to cool the clothes, if you
find them dry enough.
Post Creasecare
When available and selected, the clothes are
occasionally tumbled after the end of the drying and
cool tumble cycles, to help prevent creases
developing should you not be available to remove the
load immediately the programme is complete.
G
Note
If you have a power cut, switch off the power or
remove the plug. When the power is restored, press
the START button and the programme will resume.
7
Laundry
Sorting your laundry
Wash Care Labels
GB
G
Check symbols on clothing labels to make sure
that the articles can be tumble dried.
Sort laundry by fabric type.
Look at the labels on your garments, especially when
tumble drying for the first time. The following symbols
are the most common:
G
G
Empty pockets and check buttons.
G
Close zippers and hooks and tie loose belts and strings.
Wring out each item in order to eliminate as much
May be tumble dried
G
excess water as possible.
Do not tumble dry
! Do not load dripping wet clothes into the dryer.
Tumble dry at high heat setting
Tumble dry at low heat setting
Maximum load size
Do not load more than maximum capacity.
These numbers refer to dry weight:
Natural fibres:
Synthetic fibres:
6kg max (13lb)
3kg max (6.6lb)
What not to tumble dry in your dryer:
G
! DO NOT overload the dryer as this could result in
Articles that containing rubber or rubber-like
reduced drying performance.
materials or plastic film (pillows, cushions, or PVC
rainwear), any other flammable articles or objects
that contain flammable substances (towels soiled
with hair spray).
Typical weights
G
Note: 1kg = 1000g
Clothes
1lb = 16oz
150g
Glass fibres (certain types of draperies).
Items which have been dry cleaned.
G
G
Items with the ITCL Code
(see Special
Blouse
Dress
Cotton
5oz
clothing items). These can be cleaned with special
at-home dry cleaning products. Follow instructions
carefully.
Large bulky items (quilts, sleeping bags, pillows,
cushions, large bedspreads etc). These expand
when drying and would prevent airflow through
the dryer.
Other
Cotton
Other
100g
500g
350g
700g
3oz
1lb 2oz
12oz
G
Jeans
1lb 6oz
10 nappies
Shirt
1000g 2lb 3oz
Cotton
Other
300g
10oz
200g
125g
7oz
4oz
T-Shirt
Household Items
Duvet cover
(Double)
Cotton
Other
1500g 3lb 5oz
1000g 2lb 3oz
Large
Tablecloth700g
Tablecloth250g
1lb
6oz
Small
9oz
Tea Towel
100g
700g
350g
500g
350g
3oz
Bath Towel
Hand Towel
Double Sheet
Single Sheet
1lb 6oz
12oz
1lb 2oz
12oz
At the end of a drying cycle, cottons could still be
damp if you grouped cottons and synthetics together.
If this happens simply give them an additional short
period of drying.
G
Note
The last 10 minutes of any time set is the Cool Tumble
so allow for this when setting the time, as this period
will not dry your laundry.
8
Laundry
Times are approximate and can vary depending upon:
Special clothing items
GB
G
Amount of water retained in clothes after spin
cycle: towels and delicates retain a lot of water.
Blankets and Bedspreads: acrylic items (Acilan,
Courtelle, Orion, Dralon) must be dried with special
care on LOW heat setting. Avoid drying for a long
period of time.
Inf
p
o
tan
G
Fabrics: items that are the same type of fabric but
different textures and thicknesses may not have
the same drying time.
Pleated or creased garments: read the manufacturer’s
drying instructions on the garment.
I
G
Quantity of laundry: single items or small loads
may take longer to dry.
Starched articles: do not dry these with non-
starched items. Make sure that as much of the
starch solution is removed from the load as possible
before placing it in the dryer. Do not over-dry: the
starch will become powdery and leave your clothing
limp, which defeats the purpose of starch.
G
Dryness: If you are going to iron some of your
clothes, they can be taken out while still a bit
damp. Others can be left longer if you need them
to be completely dry.
G
Heat setting.
G
Room temperature: if the room where the dryer is
located is cold, it will take longer for the dryer to
dry your clothes.
Drying times
The table below presents APPROXIMATE drying times
in minutes. Weights refer to dry garments:
G
Bulk: some bulky items can be tumble dried with
care. We suggest that you remove these items
several times, shake them out, and return them to
the dryer until finished.
Cottons
High (full) Heat
Drying times 800-1000rpm in washing machine
Half Load
Full Load
! Do not over-dry your clothes.
1kg
2kg
3kg
4kg
5kg
6kg
All fabrics contain a little natural moisture, which
keeps them soft and fluffy.
20-30 35-45 45-60 60-70 70-80 80-100
Synthetics
High (full) Heat
Drying times on reduced spin in washing machine
Half Load
2kg
Full Load
3kg
1kg
20-40
30-50
40-70
Delicates (e.g.Acrylics)
Low (gentle) Heat
Drying times on reduced spin in washing machine
Half Load
1kg
Full Load
2kg
50-70
90-130
9
Warnings and Suggestions
G
Do not tumble dry large, very bulky items.
! The appliance has been designed and built
according to international safety standards.
These warnings are given for safety reasons and must
be read carefully.
This appliance conforms to the following
EEC Directives:
- 73/23/EEC and 93/68/EEC (Low Voltage Equipment)
- 89/336/EEC, 92/31/EEC and 93/68/EEC
(Electromagnetic Compatibility)
GB
G
G
G
Do not tumble dry acrylic fibres at high temperatures.
Complete each programme with its Cool Tumble Phase.
Do not turn off the dryer when there are still warm
items inside.
Clean the filter after each use (see Maintenance).
Do not allow lint to collect around the dryer.
Never climb on top of the dryer. It could result in
damage.
G
G
G
G
G
Always follow electrical standards and requirements
(see Installation).
Always buy original spare parts and accessories
(see Service).
General safety
G
This tumble dryer has been designed for home, and
not professional use.
G
This dryer must be used by adults, and the instructions
Recycling and disposal information
As part of our continued commitment to helping the
environment, we reserve the right to use quality recycled
components to keep down customer costs and minimise
material wastage.
in this booklet should be followed carefully.
Do not touch the appliance while barefoot or with
wet hands or feet.
Unplug the machine by pulling on the plug, not the
G
G
cord.
G
Disposing of the packaging material: follow local
G
Children must not be in proximity of the dryer when
regulations, so the packaging can be recycled.
To minimise risk of injury to children, remove the
door and plug - then cut off mains cable, flush
with the appliance. Dispose of these parts separately
to ensure that the appliance can no longer be
plugged into a mains socket.
in use. After using the dryer, turn it off and unplug
it. Keep the door closed to make sure that children
do not use it as a toy.
G
G
The appliance must be installed correctly and have
proper ventilation. The air intake vents behind the
machine, the outlet vents and the vent tube should
never be obstructed (see Installation).
Disposal of old electrical appliances
The European Directive 2002/96/EC on Waste Electrical
and Electronic Equipment (WEEE), requires that old
household electrical appliances must not be disposed
of in the normal unsorted municipal waste stream. Old
appliances must be collected separately in order to
optimise the recovery and recycling of the materials
they contain and reduce the impact on human health
and the environment.
G
Never direct the vent tube outlet towards the air
intake at the back of the machine.
Never allow the tumble dryer to recycle exhaust air.
Never use the dryer on carpeting where the pile
height would prevent air from entering the dryer
from the base.
Check to see if the dryer is empty before loading it.
G
G
G
G
The back of the dryer could become very
hot. Never touch it while in use.
The crossed out “wheeled bin” symbol on the
product reminds you of your obligation, that
when you dispose of the appliance it must be
separately collected.
G
Do not use the dryer unless the filter is securely in
place (see Maintenance).
Do not use liquid fabric softeners in the dryer, add
it to the final rinse of your wash.
G
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
G
Do not overload the dryer (see Laundry) for
maximum loads.
Do not load items that are dripping wet.
G
G
Tumble dry items only if they have been washed
with detergent and water, rinsed and been through
the spin cycle. It is a fire hazard to dry items that
HAVE NOT been washed with water.
Saving energy and respecting the
environment
G
Wring out items to eliminate excess water before
G
Carefully check all instructions on clothing labels
tumble drying (if you use a washing machine first,
select a high spin cycle). Doing this will save time
and energy during drying.
(see Laundry).
Do not dry garments that have been treated with
chemical products.
Never dry articles that are contaminated with
G
G
Always dry full loads - you save energy: single
G
items or small loads take longer to dry.
Clean the filter after each use to contain energy
flammable substances (petrol, oil, paint, hair spray,
creams, cooking fat or oils).
G
consumption costs (see Maintenance).
G
Do not tumble dry rubber, foam rubber, plastic, plastic
foam, nappy pants or liners, polythene or paper.
10
Maintenance and Care
Switching off the electricity
Check the drum after each cycle
GB
Unplug your dryer when not using it, when cleaning it
and during all maintenance operations.
Turn the drum manually in order to remove small
items (handkerchiefs) that could have been left
behind.
Inf
I
o
tan
Clean the filter after each cycle
Cleaning the drum
t
The filter is an important part of your dryer:
it accumulates lint and fluff that is formed while drying.
Small items could also become trapped in the filter.
When finished drying, therefore, clean the filter by
rinsing it under running water or with your vacuum
cleaner. Should the filter become clogged up, the airflow
inside the dryer will be seriously compromised: drying
times lengthen and you will consume more energy. It
may also damage your dryer.
! Do not use abrasives, steel wool or stainless steel
cleaning agents to clean the drum.
A coloured film may start to appear on the stainless
steel drum, this may be caused by a combination of
water and, or cleaning agents such as fabric conditioner
from the wash. This coloured film will not affect the
dryer performance.
The filter is found in front
of the dryer trim (see
diagram).
Cleaning
G
External parts in metal or plastic and rubber parts
can be cleaned with a damp cloth.
G
Periodically check the vent tube and any permanent
venting fixture to make sure that there has been
no accumulation of fluff or lint, and remove it.
G
Remove lint that collects around the filter and the
outlet vents.
Removing the filter:
1. Pull the plastic grip of
the filter upwards (see
diagram).
! Do not use solvents or abrasives.
! Your dryer uses special bearing components which
do not need lubrication.
2. Clean the filter and
replace it correctly.
Ensure the filter is fully
located flush into the
tumble dryer trim.
! Have your dryer checked regularly by authorised
technicians to ensure electrical and mechanical safety
(see Service).
! Do not use the dryer without replacing the filter.
11
Troubleshooting
One day your dryer seems not to be working. Before you call your Service Centre (see Service), go through the
following troubleshooting suggestions:
GB
Problem:
Possible causes / Solution:
G
The dryer won’t start.
The plug is not plugged into the socket, or not making contact.
G
There has been a power failure.
G
The fuse has blown. Try to plug another appliance into the socket.
G
You are using an extension cord? Try to plug the dryer’s power cord
directly into the socket.
G
The door is not closed securely?
G
The PROGRAMMES knob has not been set properly (see Start and
Programmes).
G
The START button has not been pressed (see Start and Programmes).
G
Drying cycle will not begin.
Its taking a long time to dry.
You have set a delayed time (see Start and Programmes).
G
The filter has not been cleaned (see Maintenance).
G
The correct programme has not been selected for the load (see Start
and Programmes).
G
The flexible vent tube is obstructed (see Installation).
G
The air intake vent is obstructed (see Installation).
G
The permanent ventilation flap on the storm cover is obstructed (see
Installation).
G
The items were too wet (see Laundry).
G
The dryer was overloaded (see Laundry).
Programme finishes and
clothes are damper than
expected.
! For safety the dryer has a maximum programme time of 3 hours. If an
automatic programme has not sensed the required final moisture in this
time the dryer will complete the programme and stop. Check the above
points and run the programme again, if the results are still damp, contact
the Service Centre (see Service).
G
The display shows a fault code F
followed by one or two numbers.
If the display shows F10 or F15:
- Turn off and remove the plug. Clean the filter (see Maintenance).
Then replace the plug, turn on and start another programme. If F10
or F15 is still displayed contact the Service Centre (see Service).
G
If any other number is shown: Note down the code and contact the
Service Centre (see Service).
12
Service
Before calling the Service Centre:
Spare Parts
GB
G
Use the troubleshooting guide to see if you can
solve the problem yourself (see Troubleshooting).
If not, turn off the dryer and call the Service
Centre closest to you.
This dryer is a complex machine. Repairing it yourself
or having a non-authorised person try to repair it could
cause harm to one or more persons, could damage
the machine and could invalidate the spare parts
warranty.
Inf
I
r
G
tan
Call an authorised technician if you experience problems
while using the machine.
I
The spare parts have been designed exclusively for
this appliance and not for other uses.
What to tell the Service Centre:
G
name, address and post code.
G
telephone number.
G
the type of problem.
G
the date of purchase.
G
the appliance model (Mod.).
G
the serial number (S/N).
This information can be found on the data label inside
the door of the machine.
13
1 9 5 0 4 2 5 9 9 . 0 7 W
08/2006 - SIMLEX . Four Ashes, Wolverhampton
Key Contacts
After Sales Service
Over 1100 trained specialists, directly employed by us, ensure that you can have complete
confidence in both the appliances and services we offer.
Repair Service and Information Help Desk
UK: 08709 066 066
Monday to Friday, 8am to 7.30pm
Saturday, 8.30am to 5.30pm
Sunday, 9.30am to 3.30pm
Republic of Ireland: 0818 313 413
Note: Our operators will require the following information:
Model number
Serial number
Extended Warranties
UK: 08709 088 088
Monday to Sunday, 8am to 8pm
Republic of Ireland: 0123 002 333
Genuine Parts and Accessories
UK: 08709 077 077
Monday to Friday, 8.30am to 5pm
Saturday, 8.30am to 12noon
Republic of Ireland: 0818 313 413
Indesit Company UK Limited, Morley Way, Peterborough, PE2 9JB
|