Honeywell Security Camera HD60 User Manual

You must be fully aware of all the distinctive  
features and precautions related to this  
camera before installing it.  
DIMENSIONS(mm):  
COMPOSITION:  
100.0  
Guide Pattern  
Service Monitor Cable  
Operation Manual  
Mounting Screw  
Series  
HD60  
130.6  
INSTALLATION:  
Ceiling  
Operation  
Stick the guide pattern on the  
1
SPECIFICATIONS:  
wall or ceiling.  
Guide Pattern  
Manual  
Model  
NTSC  
PAL  
Drill four holes according to  
the guide pattern then insert  
anchors into the drilled holes.  
2
Signal System  
NTSC : 525 Lines  
PAL : 625 Lines  
Scanning System  
2 : 1 Interlace  
(
(
)
)
Scanning Frequency H  
15.734kHz  
59.94Hz  
15.625kHz  
50Hz  
Dome Base  
Draw out power / video wires  
to the connecting places.  
3
4
5
1/3" Sony Super HAD CCD  
380 TV Lines Resolution  
4mm Fixed Lens  
Color Day/Night with 24 LEDs  
Auto White Balance  
Scanning Frequency V  
Image Sensor  
Total / Effective Pixels No.  
S/N Ratio  
1/3" SONY Super HAD CCD  
270K / 250K 320K / 290K  
Fixed the camera to a celling  
using four screws.  
More than 48dB (AGC Off)  
380 TV Lines  
Resolution  
Video Output Level  
Lens  
Mounting  
Screw  
Adjust desired focus and scene  
by turning and moving the  
3-axis camera bracket by hand.  
1.0 Vp-p (75 Ohms, composite)  
Fixed Lens : f=4.0mm, 81  
º
AGC, BLC, Flickerless On/Off  
Extra Video Output for Installer  
3-Axis Camera Construction  
Diameter of Bubble : 100mm  
Focus  
Manual  
Sync. System  
Sensitivity  
Electronic Shutter  
White Balance  
AGC  
Internal  
Put the dome cover over the  
base.  
6
7
0 Lux, IR LED  
1/60 ~ 100,000 Sec.  
1 /50 ~ 100,000 Sec.  
Auto  
Fix the dome cover on the base  
by covering.  
On / Off  
Dome Cover  
BLC  
Flickerless  
On / Off (with Slide Switch)  
On / Off (with Slide Switch)  
Power, Video  
READ AND KEEP THIS  
OPERATION MANUAL  
t
Input / Output Connector  
Power Consumption  
12VDC (10.8V~15V), 0.4A / 5W (Max)  
100mm  
NOTE  
(
)
Ø
Dome Size  
Weight  
Approx. 366g  
Insert coin to the side  
hole and remove the  
dome cover by twist coin.  
Need Help?  
Call 1.800.796.CCTV for sales, service and customer support.  
90º  
Design and specifications are  
subject to change without notice.  
3-axis  
Built-in  
camera  
PRECAUTIONS:  
NAME AND FUNCTION:  
bracket makes it much  
easier to rotate in any  
direction.  
360º  
Fixed Lens & IR LED Type  
!
!
Do not install the camera in  
extreme temperature conditions.  
Do use the camera under conditions where  
temperatures are within -10°C to 45°C.  
Be especially careful with ventilation  
under high temperatures.  
5
CAMERA SET-UP:  
4
3
360º  
Fixed Lens & IR LED Type  
Do not install or use the camera  
in an environment where the  
humidity is high.  
J504  
a
Function Selection Switch:  
1
2
•FL(Flickerless) ON/OFF  
AC24V  
It can cause the image quality to be poor.  
AGC(Auto Gain Control) ON/OFF  
b
BLC(Back Light Compensation)  
ON/OFF  
b
!
!
!
Do not disassemble the camera.  
There are no user-serviceable parts  
inside it.  
Service Monitor Connecter:  
Use service monitor connector  
to set camera angle & focus  
when installing.  
AC 24V  
J503  
BLC ON  
AGC OFF  
FL ON  
CAUTION : When AGC is off,  
D/N does not work because the  
D/N switching function is  
dependent on the AGC level.  
Do not drop the camera or  
1
2
3
Tilt rotation: Adjusting the vertical angle.  
Pan rotation: Adjusting the horizontal angle.  
a
subject them to physical shocks.  
It can cause malfunctions to occur.  
4
5
IR LED: 850nm / 30°(24EA)  
Sensor  
Horizontal rotation: Adjusting the horizontal  
Camera Lay-out  
position of the screen.  
Note  
TROUBLESHOOTING:  
When this camera is installed near  
wireless communication devices  
that emits strong electromagnetic  
field, irregularity such as noise on  
the monitor may appear.  
If you have trouble operating your camera, refer to the following.  
If the guidelines do not enable you to solve the problem, contact an authorized technician.  
• Power Consumption: 5W  
• IR LED Specification: 850nm / 30°(24EA)  
Check the power source for the monitor and camera  
The image does not  
appear on the screen.  
IR LED (4mm Fixed Lens)  
and ensure that the voltage and polarity are properly  
connected and being supplied correctly.  
Check if the lens is stained. If dirty, clean the lens with  
a soft, clean cloth.  
Adjust the Back Focus of the lens again.  
The image on the  
screen is dim.  
The wire is polarized. Use 12VDC power source.  
CONNECTION:  
Video Output  
GND  
Video  
#
#
1
2
Check if you have connected the camera to a proper  
power source and If there is no problem with the power,  
turn the unit off immediately and seek assistance from  
our Customer Service department.  
The camera does not work  
properly, the surface of the  
camera case is hot, and a black  
line appears on the screen.  
(Yellow)  
No. Function Terminal Color  
Remark  
Connecting to  
Monitor and Power  
#1 Video Output  
#2 Power Input  
Yellow  
Red  
1.0 Vp-p  
Check if the camera is pointed toward the sun or a  
fluorescent lamp.  
Adjust the angle or location of the camera if too much  
light is coming into the screen.  
The screen blinks a lot.  
Power - 12VDC  
(Red)  
12VDC(10.8V~15V), 0.4A/5W(Max)  
12VDC Power Type  
 

GPX Stereo System HM3817 User Manual
Graco Stroller Model Type 7431 User Manual
GSW Water Heater PART NO70999 REVG 03 12 User Manual
HannsG Computer Monitor HW173AB User Manual
Havis Shields Automobile Accessories C VS 1200 DUR User Manual
Hotpoint Refrigerator RFA52P User Manual
HP Hewlett Packard Flat Panel Television CHPTOH 0711 User Manual
Husqvarna Brush Cutter M48 Pro M53 S Pro User Manual
Image Treadmill IMTL119050 User Manual
Impex Home Gym SB 660 User Manual