Honeywell Home Security System 5804BDV User Manual

K3636V3 9/04 Rev. A  
ADEMCO 5804BDV  
TWO-WAY WIRELESS KEY with VOICE STATUS  
USER GUIDE  
About the 5804BDV  
The 5804BDV is a four-button remote control for your alarm system. It can send a command to the alarm system, such as to arm or disarm,  
as well as receive system status. Two LEDs and a speaker indicate system status. The 5804BDV is typically used for arming, disarming, and  
home automation. Check with your installer to understand which functions the buttons have been assigned on your unit.  
Operating the Buttons  
Activating a Function  
To activate a function, press and hold the appropriate button down until the yellow LED flashes, and then release it.  
Requesting System Status  
You can check system status before arming or disarming your system.  
Check your system status by momentarily pressing and releasing any button. The yellow LED will flash after you release the button. After a  
second or two, the 5804BDV will display the system status through the LEDs and speaker (see the System Status Indications Table, below).  
If the 5804BDV does not receive system status from the panel for approximately 5 seconds, it will shut itself down. It will also shut itself down  
if you do not press a button within 5 seconds of receiving a status update.  
System Status Indications Table  
LED  
LED Condition  
Speech  
System Status  
Red  
On Steady  
System Armed Away  
Armed Away or Maximum  
System Armed Stay  
Armed Stay or Instant  
Fire Alarm in progress  
Armed, Burglary Alarm in progress  
Alarm Memory  
Flashing  
Fire Fire Zone (Faulted Zone)  
Alarm Alarm Zone (Faulted Zone)  
Alarm Alarm Zone (Faulted Zone)  
System Disarmed Ready To Arm  
Green  
On Steady  
Flashing  
Flashing  
Disarmed, Ready to Arm  
System Disarmed Not Ready To Arm System Not Ready, Zones Faulted  
Yellow (right)  
Red & Green  
Indicates RF transmission  
In Enter House ID Mode  
In Set Volume Level Mode  
AC Loss Condition  
Alternately  
Flashing  
NA  
NA  
System AC Loss  
Low Battery  
Low Battery Condition  
Multiple Button Operations  
A + C Button Pair  
B + D Button Pair  
The 5804BDV should not be used  
for silent panic operation.  
WARNING!  
The 5804BDV can generate the same responses as keypad panic  
key pairs of [*] + [#] and [*] + [1] by depressing “A” + “C” and “B” +  
“D” button pairs, respectively. You must depress the button pair  
for at least 2 seconds for the 5804BDV to recognize the button pair  
command. These button pairs allow you to activate panic, fire,  
and medical alarms depending on control panel programming.  
5804BDV-005-V0  
Adjusting the Volume Level  
To enter the Volume Level mode, press and hold down the A, B, and D buttons at the same time until the unit’s red and green LEDs flash  
alternately. If no button is pressed within 5 seconds, the unit will automatically shut down and no change to the volume level is made. Press  
the A button for low volume level, the B button for mid volume level, and the C button for maximum volume level. You will hear the word  
“Alarm” at the selected volume. Then press the D button to accept the selected sound level. Note that volume level affects the life of the  
battery. Use low volume for maximum battery life.  
 

Graco Crib 9120 User Manual
Gravely Lawn Mower 252M XDZ User Manual
Hamilton Beach Air Cleaner 04532GM User Manual
Harbor Freight Tools Impact Driver 37730 User Manual
Health O Meter Scale HAB957 User Manual
Hotpoint Clothes Dryer VTD 6000 User Manual
Hotpoint Range RB526CCC User Manual
HP Hewlett Packard Camcorder CA350 User Manual
iHome MP3 Docking Station iH6 User Manual
Image Treadmill IMTL391050 User Manual