Honeywell Cell Phone 9700 MSCR User Manual

Introduction  
Attaching the MSCR to the Dolphin  
1. Press the Power key to put the terminal in Suspend  
mode.  
The Magnetic Stripe and Smart Card Reader (MSCR) for  
the Dolphin 9700 enables easy data capture with the swipe  
of a magnetic stripe card or smart card insertion. The MSCR  
snaps onto the bottom panel of the Dolphin terminal for easy  
installation or removal.  
2. Remove the stylus from the Dolphin 9700 stylus slot  
and store it in the stylus loop on the hand strap.  
3. Slide the MSCR onto the terminal until the MSCR  
snaps in place.  
Dolphin 9700-MSCR  
Software Requirements  
Note: To improve unit grip and reduce the possibility of  
accidental drop, Honeywell recommends using the  
supplied hand strap while operating the terminal with  
the MSCR attached.  
Before you connect the Dolphin terminal to the 9700-MSCR,  
make sure you have the most current software installed. To  
check the terminal’s system information, tap  
Magnetic Stripe and Smart Card Reader  
4. Press the Power key to wake the terminal.  
Start > Power Tools > SysInfo.  
Quick Start Guide  
The kernel version must be 20.01 or later in terminals  
running Windows Mobile 6.5 Classic. In terminals running  
21.01 or later. Service pack version 7 or later is required.  
Indicator LED  
D9700 MSCR Demo Application  
Not all Dolphin 9700 terminals are equipped with the D9700  
MSCR Demo application. For download and installation  
instructions, see Installing the MSCR Demo Application, in  
this quick start guide.  
Magnetic Stripe  
Card Slot  
Dolphin 9700  
Application Developer Note  
I/O Connector  
For maximum battery performance, turn off power to the  
9700-MSCR when the module is not in use.  
Smart Card Slot  
Release Latch  
with Rubber Cover  
97-MSCR-QS Rev A  
12/10  
Note: You can swipe the card from  
either the left or the right. Make  
sure the magnetic stripe of the  
card is facing down, toward the  
I/O connector as shown.  
MSCR LED Indicator  
Using the MSCR Demo Application  
The single LED indicator located on the top surface of the  
MSCR housing denotes the communication status and the  
selected function (i.e., Magnetic Stripe Reader or Smart  
You can use the MSCR Demo application to verify that the  
Dolphin 9700 terminal can receive data from the MSCR.  
Starting the MSCR Demo Application  
Card Reader).  
2. The LED rapidly flashes green four times to indicate a  
good read. The data from the card appears on the  
terminal’s screen.  
1. On the Dolphin terminal, tap Start > File Explorer >  
My Device > Program Files > D9700 MSCR Demo >  
D9700MSCRTest.  
This color and status  
means . . .  
Green  
active  
Green LED activity indicates the  
Magnetic Card function is  
selected.  
Note: If the LED does not flash, the card swipe was not  
successful.  
Note: Not all Dolphin 9700 terminals are equipped with the  
D9700 MSCR Demo application. For download and  
installation instructions, see Installing the MSCR Demo  
Application, in this quick start guide.  
Slow Flashing  
Solid  
The MSCR has power and is idle.  
Testing the Smart Card Reader  
A magnetic stripe card is being  
swiped/read.  
2. Connect the MSCR to  
the Dolphin terminal.  
1. Remove the Rubber Cover  
protecting the smart card  
slot.  
Fast Flashing  
The MSCR has successfully read  
the magnetic card.  
3. Verify COM1 is  
selected from the pull  
down menu.  
Note: Do not discard the rubber  
cover. The cover protects  
the smart card slot when  
not in use.  
This color and status  
means . . .  
4. Check the box next to,  
Yellow  
active  
Yellow LED activity indicates the  
Smart Card function is selected.  
Power.  
Note: The LED indicator on the MSCR emits a single long  
green flash and then flashes approximately every three  
seconds. By default, the Magnetic Stripe Reader function  
is activated when power is supplied to the MSCR.  
2. Select SCR. The LED  
indicator changes to yellow,  
emits a single long flash,  
and then flashes every  
3 seconds.  
Slow Flashing  
Fast Flashing  
The MSCR has power and is idle.  
The Dolphin is performing smart  
card read/write operations.  
Testing the Magnetic Stripe Reader  
1. Swipe a magnetic stripe card. The green LED stays illu-  
minated for the duration of the swipe.  
 

Graco Inc Paint Sprayer 233700 User Manual
Graco Sleep Apnea Machine PD183658A User Manual
HANNspree Flat Panel Television LT0B 15U1 000 User Manual
Harbor Freight Tools Nail Gun 46309 User Manual
HP Hewlett Packard Camcorder V5061u User Manual
HP Hewlett Packard Personal Computer xw8000 User Manual
HP Hewlett Packard Stereo Receiver 2714A User Manual
Hyundai Automobile Accessories 99 7300 User Manual
IBM Computer Monitor 9516 BXX User Manual
Ice O Matic Ice Maker Storage Bin User Manual