THE BRIDGE II
DOCKING STATION FOR iPod
OWNER’S MANUAL
0057CSK - HK Bridge II All v10.indd
1
10/02/09 10:32:04
InSTALLATIOn
step three: Place the black insert in The Bridge II,
making sure to push it all the way down. See Figure 3.
InstallIng
With only a single cable connection, The Bridge II is
easy to connect to your Harman Kardon product.
nOtE: Do not place an iPod in The Bridge II unless
both the black insert and a dock adapter are installed.
Otherwise, the iPod will not connect properly, and
both it and the Bridge II may sustain damage that
is not covered by the warranty.
step One: Turn off the Harman Kardon The Bridge-
or The Bridge II-ready product, using its master power
switch.
step two:
-Ready Products – Holding the
cable with the wider part of the connector at the
bottom, gently squeeze the tabs on each side as
you insert it into the connector on the rear panel of
the Harman Kardon product. See Figure 1.
step Five
step Four
step three
Figure 3 –
Docking an iPod
in The Bridge II
Figure 1 – The Bridge II connector on The Bridge II-ready
Harman Kardon products
-Ready Products – A different con-
nector was used on The Bridge-ready Harman Kardon
products and the HK3490, as shown in Figure 2. Do
not plug The Bridge II directly into the DMP/The Bridge
connector on the rear panel of these products. First,
connect the included adapter to The Bridge II cable,
then plug the adapter into the product.
step Four: Locate the dock adapter that was
included with your iPod, or select one of the included
clear dock adapters by referring to Table 1. If your iPod
is an older model that does not appear in Table 1 and
that did not include an adapter, contact Apple Inc. to
purchase one.
Place the adapter in The Bridge II insert, as shown
in Figure 3.
step Five: Remove the iPod from any case, and
dock it in The Bridge II, as shown in Figure 3.
Figure 2 – The DMP/The Bridge connector on The Bridge-ready
Harman Kardon products
table 1 – select the Correct the Bridge II Insert
The Bridge II Insert
NANO
iPod Model
iPod nano, 1st and 2nd generation
5G (VIDEO 60GB)
5G (VIDEO 30GB)
13
iPod, 5th generation (60GB, 80GB) and iPod classic (160GB)
iPod, 5th generation (30GB) and iPod classic (80GB)
iPod nano, 3rd generation
12, 14
iPod touch – install large bumper
3
0057CSK - HK Bridge II All v10.indd
3
10/02/09 10:32:16
OPERATIOn
Photos may be viewed on an external monitor only for
iPod models that support video browsing (see note
below). Select the desired photo, then press the play
button on the iPod, or press the OK or Enter Button on
the remote three times.
UsIng
Once The Bridge II is connected, use either the front-
panel controls or The Bridge-ready product’s remote
control to select tracks for playback. Press the DMP/
The Bridge Button on the remote, or use the Source
Selector on the front panel to change sources. When
an iPod is docked, a message will appear in the
front-panel and on-screen displays, indicating that
The Bridge II is connected. The displays will switch to
the navigation menus, and the menu screen on the
iPod itself will be replaced by a Harman Kardon logo
graphic and a message reading “OK to Disconnect.”
To view videos, when available on an iPod that sup-
ports video browsing, press the Menu Button and
select the “Videos” option. For The Bridge II-ready
products, the iPod will remain in Extended Mode. Use
the AVR remote and the on-screen menus to select
video content. For The Bridge-ready products, the
iPod may switch to Manual Mode. Use the Harman
Kardon remote or the controls on the iPod with the
screen on the iPod to view videos.
When you see the “OK to Disconnect” message displayed,
the iPod is in Extended Mode and may be operated
using the Harman Kardon product’s front-panel or
remote controls. The controls for most The Bridge- and
The Bridge II-ready products are described in Table 2.
The blank boxes indicate that the function is not
available using those controls. Because the specifics
of operation vary by product, please review the owner’s
manual for detailed information.
To return to Extended Mode from Manual Mode, press and
hold the Menu Button on the receiver’s remote control.
nOtEs On VIDEO PlaYBaCK:
• As of this writing, video browsing is only supported
on the iPod 5G, iPod classic and iPod nano (3rd gen-
eration). For other iPod models (except the iPod 4G),
it is not possible to view photos or videos on an
external monitor with The Bridge II. However, you
may purchase an A/V cable from Apple Inc. that
has conventional audio and video plugs that may be
connected to any available
While a selection is playing, the song title, artist and
album name (if available) will scroll across the upper
line in the front-panel Message Display. The lower line
will display the elapsed time of the track on the left, the
play mode icon, and the time remaining on the right.
analog inputs on the AVR.
If a video display is connected to the Harman Kardon
product, the available track information will appear there
as well, along with the time and play mode displays.
• Before attempting to play videos stored on your iPod,
check that the TV Out setting on the iPod is set to On.
Adjust any other settings on the iPod as appropriate
for your system. If your selection was playing and
paused at the time you changed the TV Out setting,
the iPod may require you to navigate its menu system
and reselect the video. Resuming play from the
“Now Playing” function may not reflect the change
to the TV Out setting.
Some Harman Kardon The Bridge- and The Bridge
II-ready products include a settings menu that allows
you to select Repeat or Random playback or Resume
mode. Refer to the product’s manual for more infor-
mation.
Playback of photos, when available, is different from
audio playback. Press the Menu Button and select the
photo option to switch to Manual Mode. In Manual
Mode, the iPod may be operated using its own controls
or the receiver’s remote, and its menus will appear
in place of the Harman Kardon logo and “OK to
Disconnect” message. The menus generated by the
receiver while using The Bridge II do not appear in
Manual Mode.
• In Manual Mode, the menus for the iPod will only be
visible on its screen. You may operate the iPod using
the receiver’s remote, as long as it is in The Bridge
device mode.
4
0057CSK - HK Bridge II All v10.indd
4
10/02/09 10:32:20
OPERATIOn
Charging the iPod
Undocking the iPod
You may leave your iPod in The Bridge II even when
you are not using it as a playback source. Whenever
the iPod is docked and your receiver is turned on,
The Bridge II will charge the battery in the iPod.
We recommend that you pause playback before
physically removing the iPod from The Bridge II.
IMPORtant nOtE: When using The Bridge II
with the DMC 1000, do not remove the iPod from
The Bridge II without first selecting the “Undock iPod”
option in the on-screen menu.
Some Harman Kardon receivers allow you to charge
the battery in the iPod when the receiver is turned off
(i.e., in the “Standby” mode). Consult your receiver’s
owner’s manual for more information.
table 2 – Controlling the iPod
-Ready Products
-Ready Products
Function on iPod
Play
Remote Control Key Front-Panel Button Remote Control Key
›
›
Play ( )
Tuner Mode
Tuner Mode
Play ( )
Pause
Pause (II
)
Pause (II)
Menu
Menu (Spkr)
Set
Tuner Band (AM/FM) Menu
Select
Set
OK
Left Arrow (
‹
‹
Scroll Reverse
Scroll Forward
Left Arrow (
)
Preset Down
Preset Up
Tuning Up
)
›
›
Right Arrow ( )
Right Arrow ( )
››
››
Forward
Forward/Next (
I
)
Forward/Next (
I)
Search/Next Track
‹‹
I
‹‹
Reverse
Reverse/Previous (
)
Tuning Down
Reverse/Previous (
I
)
Search/Previous Track
Page Up/Down
Channel/Page Up/Down
5
0057CSK - HK Bridge II All v10.indd
5
10/02/09 10:32:25
TROUBLESHOOTInG
tROUBlEsHOOtIng gUIDE
sYMPtOM
sOlUtIOn
The iPod does not play or respond to
commands from the receiver’s remote.
• Make sure that The Bridge II is properly connected
to a compatible Harman Kardon receiver.
• Make sure that DMP or The Bridge is selected as
the input on the receiver.
The LED under The Bridge II goes out
when the receiver is in the Standby mode.
• Check the menu setting on your receiver to make sure
that the option to charge iPod while in Standby mode is
turned on, if available.
• Make certain that the receiver is in the Standby mode
by looking for the amber standby light. The iPod will not
charge when the Master Power Switch is off.
The display and controls on the iPod
do not operate in iPod mode.
• This is normal and does not indicate a problem
with the iPod, The Bridge II or your receiver.
sPECIFICatIOns:
Dimensions (H x W x D): 1-3/16” x 4-1/2” x 4-1/2” (30mm x 114mm 114mm)
Weight: 0.37 lb (0.17kg)
© 2008 Harman International Industries, Incorporated. All rights reserved.
Harman Kardon is a trademark of Harman International Industries, Incorporated, registered in the United States
and/or other countries. Designed to Entertain, The Bridge logo and The Bridge II logo are trademarks of Harman International Industries, Incorporated.
iPod is a trademark of Apple Inc., registered in the U.S. and other countries. iPod not included. “Made for iPod” means that an electronic accessory has
been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Apple is not responsible
for the operation of this device or its compliance with safety and regulatory standards.
Features, specifications and appearance are subject to change without notice.
6
0057CSK - HK Bridge II All v10.indd
6
10/02/09 10:32:29
STAPLE InVOICE HERE
7
0057CSK - HK Bridge II All v10.indd
7
10/02/09 10:32:33
250 Crossways Park Drive, Woodbury, New York 11797
© 2008 Harman International Industries, Incorporated.
All rights reserved.
Part No. 950-0236-001
0057CSK - HK Bridge II All v10.indd
8
10/02/09 10:32:00
|