3” COMPOSITE AIR CUT-OFF TOOL
95028
ASSEMBLY And OPERATInG
InSTRUCTIOnS
due to continuing improvements, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
TO PREVEnT SERIOUS InjURY,
REAd And UndERSTAnd ALL WARnInGS
And InSTRUCTIOnS BEFORE USE.
Copyright© 2006 by Harbor Freight Tools® . All rights reserved. No portion of this manual or any
artwork contained herein may be reproduced in any shape or form without the express written
consent of Harbor Freight Tools.
For technical questions and replacement parts, please call 1-800-444-3353.
6.
Stay alert. Watch what you are doing and use common sense when operating a
pneumatic tool. do not use a pneumatic tool while tired or under the influence
of drugs, alcohol or medication. Doing so may result in serious personal injury.
7. dress properly. do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts.
8. Avoid accidental starting. Be sure the Trigger Lever (14) is off before connecting
to the air supply. Carrying pneumatic tools with your finger on the Trigger, or
connecting pneumatic tools to the air supply with the Trigger on, invites accidents.
9. Remove adjusting keys or wrenches before turning on the tool. A wrench or a key
that is left attached to a rotating part of the tool may result in personal injury.
10. do not overreach. Keep proper footing and balance at all times. Proper footing
and balance enables better control and of the toll in unexpected situations.
11. Use safety equipment. Always wear AnSI-approved safety glasses under-
neath a full face shield, and hearing protection.
12. Replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty. Only use accessories
intended for use with this tool. Approved accessories are available from Harbor Freight
Tools.
13. do not operate tool if under the influence of alcohol or drugs. Read warning
labels if taking prescription medicine to determine if your judgement or reflexes are
impaired while taking drugs. If there is any doubt, do not operate the Cut-Off Tool.
14. Use proper size and type extension cord. If an extension cord is required, it must
be of the proper size and type to supply the correct current to the compressor without
heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical
damage to the compressor. Check your air compressor’s manual for the appropriate
size cord.
15. Maintenance. For your safety, maintenance should be performed regularly by a
qualified technician.
16. Compressed air only. Use clean, dry regulated, compressed air at 90 PSI. Never
use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power
source for this tool.
17. When connecting to the air supply: Prior to each use, if an automatic oiler is not
used, add two drops of air tool oil (not included) into the Air Inlet (13) fitting of the Cut-
Off Tool.
18. Always disconnect the Cut-Off Tool from its compressed air supply source, and
squeeze the Trigger Lever (14) to release all compressed air in the tool before
performing any maintenance or services.
note: Performance of the compressor (if powered by line voltage) may vary depending on
variations in local line voltage. Extension cord usage may also affect tool performance.
SKU 95028
For technical questions, please call 1-800-444-3353
Page 3
19. Industrial applications must follow OSHA requirements.
20. Warning: Use 3” Cutting disc. Only use a standard 3” cutting disc (rated at
20,000 RPM or greater) with this Cut-Off Tool. never use any other kind of disc,
blade or cutter. do not bind the cut-off wheel/disc.
21. Warning: Some dust created by power sanding, sawing, grinding, drilling
and other construction activities contain chemicals known (to the State of
California) to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are: lead from lead-based paints, crystalline silica
from bricks and cement or other masonry products, arsenic and chromium
from chemically treated lumber.Your risk from these exposures varies,
depending on how often you do this type of work.To reduce your exposure to
these chemicals: work in a well ventilated area and work with approved safety
equipment, such as those dust masks that are specifically designed to filter out
microscopic particles (California Health & Safety Code 25249.5, et seq.)
Unpacking
When unpacking, check to make sure the parts listed on page 7 are included. If any
parts are missing or broken, please call Harbor Freight Tools at the number on the cover of
this manual as soon as possible.
Assembly and Operating Instructions
For best service, you should incorporate an oiler, regulator, and inline filter, as shown
in the diagram above. Hoses, couplers, oilers, regulators, and filters are all available
at Harbor Freight Tools.
Cut-Off
Tool
SKU 95028
For technical questions, please call 1-800-444-3353
Page 4
Assembly and Operation Instructions (continued)
note: Performance of the compressor (if powered by line voltage) may vary depending
on variations in local line voltage. Extension cord usage may also affect tool
performance.
1.
You will need to prepare a 1/4” air connector (sold separately) to connect to the Air Inlet
(13) on the Air Cut-Off Tool. First, wrap the 1/4” air connector (not included) with pipe
thread seal tape before threading into the Air Inlet (13). Connect a 3/8” I.D. Air Source
Hose to the Cut-Off Tool.
note: If you are not using an automatic oiler system, before operation add a few drops
of Pneumatic Tool Oil to the airline connection. Add a few more drops after each hour
of continual use.
2.
Set the air pressure on your compressor to 90 PSI. Do not exceed the recommended
air pressure of 90 PSI.
3.
4.
5.
Check the air connection for leaks.
Disconnect the air hose until instructed to reconnect.
After disconnecting the air supply, squeeze the Trigger Lever (14) to make sure no air
remains in the unit.
Assembly:
The only assembly required is the mounting of the Cutting Wheel (29).
Warning: the Cut-Off Tool must be disconnected from the air supply when changing
the Cutting Wheel (29). After disconnecting the air supply, squeeze the Trigger Lever
(14) to make sure no air remains in the unit.
1.
2.
3.
4.
Place the Wrench (33) on the flats of the Spindle (25) to hold it in place.
Using the Allen Wrench (32), loosen and remove Hex Screw (31) and Spacer (30).
Remove and replace the Cutting Wheel (29).
Replace the Hex Screw (31) and the Spacer (30). Tighten the Hex Screw (31) while
holding the Spindle (25) in place with the Wrench (33). See Figure 1.
Spindle (25)
Cutting Wheel (29)
Spacer (30)
WARnInG: The Guard (27)
must be in place when using
Hex Screw (31)
the Cut-Off Tool.
Guard (27)
Allen Wrench (32)
Figure 1
SKU 95028
For technical questions, please call 1-800-444-3353
Page 5
Assembly and Operation Instructions (continued)
WARnInG: Always check the Cutting Wheel (29) for possible wear. Do not use a worn, torn,
or defective cutting wheel.
WARnInG: Position the Cut-Off Tool so that the attached guard is in position between you
and the workpiece to protect you from flying debris.
WARnInG: The Guard (27) must always be attached to the Cut-Off Tool.
1.
2.
3.
4.
Check the Cutting Wheel (29) for wear, Replace if necessary.
Set the compressor to 90 PSI. Do not exceed 90 PSI.
Connect the Cut-Off Tool to the air hose as explained on Page 5 of this manual.
Use both hands to grip the Cut-OffTool. Gently squeeze down on the Trigger Lever
(14). Allow the Cut-Off Tool to run for a few seconds before approaching the work-
piece.
5.
6.
7.
8.
Let the Cut-Off Tool do the work. Do not apply force on the workpiece.
When finished, release the Trigger Lever (14).
Disconnect the Air Hose.
Gently squeeze down on the Trigger Lever (14) to release any air that might still remain
in the Cut-Off Tool.
Inspection, Maintenance, and Cleaning
1.
2.
Warning: Always release any excess air, make sure theTrigger Lever (14) is in its
“OFF” position, and disconnect the Cut-OffTool from its compressed air supply
before performing any inspection, adjustments, maintenance, or cleaning.
Before each use, inspect the general condition of the Cut-Off Tool. Check for loose
screws, misalignment or binding of moving parts, cracked or broken parts, damaged
air hose, and any other condition that may affect its safe operation. If abnormal noise or
vibration occurs, have the problem corrected before further use. never use damaged
equipment.
3.
After each use, wipe down the Cut-Off Tool with a clean cloth, remove all dirt, oil, and
grease from the Cut-Off Tool. If necessary, you may use a mild detergent. Do not use
solvents, as damage to the Cut-Off Tool may occur. Do not immerse the Cut-Off Tool
in any liquids.
SKU 95028
For technical questions, please call 1-800-444-3353
Page 6
Parts List and diagram
Part
1
description
Plug Screw
Q’ty
1
Part
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
description
Q’ty
2
Ball
2
O-Ring
1
Rotor Blade
Rotor
4
3
O-Ring
1
1
4
Air Regulator
Valve Spring
O-Ring
1
Cylinder
Bearing Plate
Bearing
1
5
1
1
6
1
1
7
Valve Stem
O-Ring
1
Washer
1
8
1
Spindle
1
9
Motor Housing
Valve Bushing
O-Ring
1
Lock Ring
Guard
1
10
11
12
13
14
15
16
17
1
1
2
Nut
1
Muffler
1
Cutting Wheel
Spacer
1
Air Inlet
1
1
Trigger Lever
Lever Pin
Bearing
1
Hex Screw
Allen Wrench
Wrench
1
1
1
1
1
Bearing Plate
1
nOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.
SKU 95028
For technical questions, please call 1-800-444-3353
Page 7
Warranty
Limited 1Year
warrantY
Harbor FreightTools Co.makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 1 year from the date of purchase.This warranty does not apply to damage due directly or indirectly, to
misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special
or consequential damages arising from the use of our product. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you.THiS
WarranTy iS expreSSly in lieu oF all oTHer WarranTieS, expreSS or implied, inCluding
THe WarranTieS oF merCHanTabiliTy and FiTneSS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid.
proof of purchase date and an explanation of the complaint must accompany the merchandise. if our inspection
verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our
expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of
our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
PLEASE REAd THE FOLLOWInG CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM INTHIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU-
TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT
HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE
IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 95028
For technical questions, please call 1-800-444-3353
Page 8
|