1/4 HP SUBMERSIBLE
WATER PUMP
98342
SET UP And OPERATIng InSTRUcTIOnS
®
distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MAnUAL.
©
®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
2. Make sure that the socket is suf-
ficiently secured and is in excellent
condition.
UnPAckIng
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
3. When the plug is inserted into the
socket the pump will be on standby.
WARnIng! If the power cord or plug is
damaged, do not use the pump. The
power cord or plug may only be re-
paired by a certified electrician.
InSTALLATIOn
The submersible motor pump must
be installed in a stationary position with
either:
Areas of use
1. This pump is designed for use as a
basement pump. When installed in a
shaft, this pump provides some pro-
tection from basement flooding.
a. A fixed pipeline or
b. A flexible hose pipe.
2. This pump can also be used to trans-
fer water (e.g. household, farming,
plumbing).
Please note!
1. Do not install the pump by suspend-
ing it unsupported from its delivery
pipe or power cord. The pump must
be suspended from the handle or be
placed on the bottom of the shaft. To
ensure that the pump works properly,
keep the bottom of the shaft free from
sludge and dirt of all kinds.
OPERATIOn
After reading these instructions, con-
sider the following points before starting
the pump:
1. Verify that the pump rests on the floor
of the shaft, if it is not suspended by
the handle.
2. If the water level sinks too low, any
sludge in the shaft will dry out and
stop the pump from starting. To help
ensure the pump will start as re-
quired, check the pump regularly with
start-up tests.
2. Verify that the delivery pipe is prop-
erly connected.
3. Verify that the electrical connection is
115 V~, 60 Hz.
3. The pump must be installed with an
automatic float switch (not included)
to prevent running dry.
4. Verify that the electrical socket is in
good condition.
Power Supply
5. Verify that water and moisture cannot
get near the power supply socket.
1. The pump is equipped with a shock-
proof plug according to regulations.
The pump is designed to be connect-
ed to 115 V~, 60 Hz safety socket.
6. Verify that the pump is installed so as
to prevent running dry.
SKU 98342
For technical questions, please call 1-800-444-3353.
Page 3
FIgURE B
MAInTEnAncE
IMPELLER
(14)
TO PREVEnT
SERIOUS InjURy
FROM AccIdEnTAL
OPERATIOn:
Unplug the Pump from its
electrical outlet before
performing any inspection,
maintenance, or cleaning
procedures.
If the pump is moved during op-
eration, flush it out with clean water after
every use.
FILTER
(11)
Quarterly Maintenance
The below maintenance must be per-
formed at least once every 3 months under
optimal conditions. For frequent use, or
dirty areas, more frequent maintenance is
required.
a. Remove the Filter (11) from the
pump case.
b. Clean the impeller with clean water.
c. To prevent damage, do not rest the
pump on the impeller or pry against
the impeller.
1. Clean sludge and debris from the bot-
tom of the shaft.
2. Rinse the housing off with clean wa-
ter.
d. Reassemble in reverse order.
3. Clean fibers from inside the pump
housing with a pressure washer (not
included).
4. If the pump housing cannot be
cleaned from the outside, it must be
thoroughly cleaned. Make sure the
power cord is unplugged before
maintenance. Dismantle the bottom
part of the pump as follows:
SKU 98342
For technical questions, please call 1-800-444-3353.
Page 4
Troubleshooting
Problem
Pump runs, but
will not deliver any
water.
Possible causes
Possible Solutions
1. Filter and/or impeller clogged. 1. Remove filter. Clean out dirt and debris from
filter and impeller. Then replace Filter.
2. When starting, the pump water 2. There must be at least 1/8” deep water for the
height (1/8”) falls below the
minimum water level.
Pump to operate properly.
3. Low line voltage.
3. Consult with an electrician.
4. Optional check valve stuck or 4. Remove and examine check valve.
installed backwards.
Pump won’t start
or run.
1. Check power connections and 1. Consult with an electrician.
circuits/fuses.
2. Water level too low.
2. Allow water level to rise above 1/8”, or move
Pump to a lower location.
3. Filter and/or impeller clogged. 3. Remove filter. Clean out dirt and debris from
filter and impeller. Then replace filter.
4. Defective motor.
4. Have a qualified service technician repair or
replace.
Excessive noise or 1. Worn bearings.
vibration.
1. Have a qualified service technician repair or
replace.
2. Debris in impeller.
2. Remove filter. Clean impeller. Then replace
filter.
3. Discharge garden hose
restricted.
3. Clean Pump and discharge garden hose.
Pump starts
and stops too
frequently.
1. Water temperature too high.
1. Do not exceed temperatures above 95°
Fahrenheit.
2. Back flow of water from
2. Install or inspect optional check valve.
discharge garden hose.
Follow all safety precautions whenever diagnosing or servicing the
tool. disconnect power supply before service.
PLEASE REAd THE FOLLOWIng cAREFULLy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT
HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
qUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN By CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE
BUyER ASSUMES ALL RISK AND LIABILITy ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 98342
For technical questions, please call 1-800-444-3353.
Page 5
PARTS LIST
Part
1
description
Power Cord & Plug
Water Outlet
Qty.
1
Part
description
Qty.
5
16 Screw
17 Screw
2
1
1
3
Pump Shell
1
18 Hold Down Ring
19 O-Ring
1
4
O-Ring
1
1
5
Cable Guard
1
20 Oil Seal
3
6
Cable Compaction Buckle
Capacitor
1
21 Motor Foreside
22 O-Ring
1
7
1
1
8
Cable Compaction Board
Screw
1
23 Motor Lining
24 Stator
1
9
3
1
10 Screw
11 Filter
12 Base
13 Nut
4
25 Bearing
2
1
26 Rotor
1
1
27 Washer
1
1
28 Back Cover
29 Wire Jacket
1
14 Impeller
15 Washer
1
1
1
SKU 98342
For technical questions, please call 1-800-444-3353.
Page 6
ASSEMBLy dIAgRAM
SKU 98342
For technical questions, please call 1-800-444-3353.
Page 7
LIMITEd 1 yEAR / 90 dAy WARRAnTy
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that for a period
of ninety days from date of purchase that the engine/motor, the belts (if so equipped),
and the blades (if so equipped) are free of defects in materials and workmanship. Har-
bor Freight Tools also warrants to the original purchaser, for a period of one year from
date of purchase, that all other parts and components of the product are free from
defects in materials and workmanship (90 days if used by a professional contractor or
if used as rental equipment). This warranty does not apply to damage due directly or
indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our
facilities, normal wear and tear, or to lack of maintenance. We shall in no event be liable
for death, injuries to persons or property, or for incidental, contingent, special or con-
sequential damages arising from the use of our product. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation
of exclusion may not apply to you. THIS WARRANTy IS EXPRESSLy IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF
MERCHANTABILITy AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
Record Product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 98342
For technical questions, please call 1-800-444-3353.
Page 8
|