Harbor Freight Tools Power Hammer 91670 User Manual

HEAVY DUTY  
HAMMER TACKER  
91670  
ASSEMBLY AND OPERATING INSTRUCTIONS  
®
3491 Mission Oaks Blvd., Camarillo, CA 93011  
Copyright © 2004 by Harbor Freight Tools®. All rights reserved. No  
portion of this manual or any artwork contained herein may be  
reproduced in any shape or form without the express written consent of  
Harbor Freight Tools.  
For technical questions and replacement parts,  
please call 1-800-444-3353.  
 
6.  
7.  
When loading staples, always adhere to all the instructions and  
safety warnings provided in this manual. Reminder: Avoid injuries  
from sharp staples when loading and cleaning this product.  
Be sure material will accept staples. Always test the material to  
see if the staples will hold the material you want to secure. Staples  
will not hold stone, rock or metal. Best suited for roofing installation,  
carpet installation, poly sheeting and upholstery.  
Note: The Hammer Tacker is only to be used to strike the material to be  
secured. Do not use for any other purpose.  
Warning: The warnings, cautions, and instructions discussed in this  
instruction manual cannot cover all possible conditions and situations that  
may occur. It must be understood by the operator that common sense and  
caution are factors which cannot be built into this product, but must be  
supplied by the operator.  
Unpacking  
When unpacking, check to make sure the following parts are included  
that are listed on Page 5. If any parts are missing or broken, please call  
Harbor Freight Tools at the number on the cover of this manual.  
Assembly Instructions  
1.  
You must first load staples (not included) into the Hammer Tacker.  
Press the Staple Feeder Button (1) by squeezing the sides together.  
While squeezing, push inward and downward to unlock the Staple  
Spring Feeder (2). See Figures A & B.  
Handle (3)  
Staple  
Loading Area  
Staples Exit  
Feeder  
Button  
(1)  
Figure A  
REV 06/04  
SKU 91670 For technical questions, please call 1-800-444-3353.  
Page 3  
 
2.  
Pull out the Staple Spring Feeder (2). Set aside. Insert a strip of  
staples (not included, see Page 2 for size). Place staples in the track  
of the loading area. Slide the Staple Spring Feeder (2) back into the  
Hammer Tacker. Squeeze and push the Spring Feeder Button (1)  
upward to lock it into position. If Spring Feeder will not go all the way  
back into place, remove some staples from the magazine.  
See Figures A, B &C .  
Staple Feeder Button (1)  
Staple Spring Feeder (2)  
Figure B  
Figure C  
Operation  
1.  
To use the Hammer Tacker for roofing, carpeting, poly sheeting or  
upholstery, hold Handle (3) like you would a hammer and hit the area  
you wish the staple to hold. Avoid hitting your fingers or other body  
parts.Test first on a scrap-piece of material to make sure the Hammer  
Tacker is working properly and that the staples are fully driven into the  
workpiece. Always wear ANSI approved impact safety goggles when  
using this product.  
Maintenance  
1.  
2.  
Store indoors, and keep dry to avoid rusting.  
If Hammer Tacker becomes jammed with staples, use needle nose  
pliers (not included) and remove bent or jammed staples.Always wear  
ANSI approved safety goggles when removing jammed staples.  
Repeat loading instructions on Page 3.Test on scrap material to see if  
Hammer Tacker will work correctly after this repair. See Figure E.  
Needle Nose Plier  
Figure E  
SKU 91670 For technical questions, please call 1-800-444-3353.  
Page 4  
 
Note: No replacement parts are available.  
Staple  
Spring  
Feeder  
Staple  
Feeder  
Button  
Staple Exit  
Handle  
Staple Loading Area  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM  
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER  
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND  
TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE  
PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE  
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY  
STATESTHAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN  
BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER.THE BUYER  
ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE  
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERE TO, OR ARISING OUT OF  
HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERE TO.  
NOTE: Some parts are listed and shown for illustration purposes only and are  
not available individually as replacement parts.  
SKU 91670 For technical questions, please call 1-800-444-3353.  
Page 5  
 

Healthrider Home Gym HREL05983 User Manual
Heath Zenith Home Safety Product 598 1165 03 User Manual
Honeywell Home Security System LYNXR 2 User Manual
HP Hewlett Packard Camcorder PW460T User Manual
HP Hewlett Packard Computer Hardware XW User Manual
Husqvarna Blower 966529103 User Manual
Husqvarna Tiller crt51 User Manual
Hyundai Automobile PDF Ebook Library User Manual
IBM Printer HL 5240 User Manual
Ikelite Digital Camera DSC P150 User Manual