Harbor Freight Tools Patio Furniture 92928 User Manual

PORTABLE GARAGE  
CAR CANOPY  
92928  
ASSEMBLY INSTRUCTIONS  
Read this material before using this product.  
Failure to do so can result in serious injury.  
SAVE ThIS MANUAL.  
Copyright© 2005 by Harbor Freight Tools®. All rights reserved. No portion of this  
manual or any artwork contained herein may be reproduced in any shape or form  
without the express written consent of Harbor Freight Tools. Diagrams within this  
manual may not be drawn proportionally. Due to continuing improvements, actual  
product may differ slightly from the product described herein. Tools required for  
assembly and service may not be included.  
For technical questions or replacement parts, please call 1-800-444-3353.  
Revised Manual 09k  
 
11. Replacement parts. When servicing, use only identical replacement parts.  
Use of any other parts will void the warranty.  
12. Do not assemble if under the influence of alcohol or drugs. Read warning  
labels on prescriptions to determine if your judgment or reflexes are impaired  
while taking drugs. If there is any doubt, do not assemble the product.  
13. Heavy, wet snow or extremely windy conditions could damage the Car  
Canopy. It is recommended that the Tarp be removed under these conditions  
to prevent damage to the Car Canopy or nearby property.  
Warning: The warnings, cautions, and instructions discussed in this instruction  
manual cannot cover all possible conditions and situations that may occur. It must  
be understood by the operator that common sense and caution are factors which  
cannot be built into this product, but must be supplied by the operator.  
Unpacking  
When unpacking, check to make sure that all parts are included. Refer to parts  
list on the last page of this manual. If any parts are missing or broken, please call  
Harbor Freight Tools at the number on the cover of this manual.  
Assembly  
1. Place 17 Steel Tubes (1) on the ground as illustrated below.  
Caution: Be alert to possible wind damage; prolonged exposure to wind can cause  
fasteners and hardware to loosen as the frame flexes. The Portable Garage Car  
Canopy’s frame strength will be compromised if fasteners and hardware are not  
tight. Periodically check and make sure all fasteners and hardware are tight. Tubes,  
stakes, tie downs and rope should also be periodically checked to make sure the  
unit is always structurally rigid.  
SKU 92928  
For technical questions, please call 1-800-444-3353.  
Page 3  
 
2. Connect 3-way and 4-way Tube Fittings (2 and 3) as shown below. At each  
junction, there is a hole through the side of the Fitting that lines up with the  
hole in the side of the Tube. Line up these holes on the inside of the structure  
and insert Self-tapping Screws (8), but tighten them only slightly at this time.  
3. Drape Tarp (7) over assembled frame and secure the corners (first) onto the  
frame using the Ball Tie Downs (4) as shown in 4A, B, and C, below.  
4. Once the corners are fastened, place the Ball Tie Downs through the balance  
of the metal eyelets as shown in the previous illustration, 4D.  
5. Lift one side of the roof and slide in four Steel Tubes (1). Line up the holes in  
the Tubes with the holes in the Fittings and insert Self-tapping Screws (8), but  
tighten them only slightly at this time.When  
complete, do the same to the other side.  
See illustration to the right.  
6. Insert the Nylon Base (5) onto each  
vertical leg.  
7. Secure each Nylon Base to the ground  
Nylon Base (5) fits here.  
REV 09e  
SKU 92928  
For technical questions, please call 1-800-444-3353.  
Page 4  
 
using the T-Stakes (6). Tighten all Self-tapping Screws (8) securely.  
Maintenance  
1. Periodically clean Tarp using mild soap and water.  
2. Periodically disassemble and apply a light oil to the Steel Tubes to prevent  
rusting.  
Parts List  
Item #  
Description  
Qty  
1
2
3
4
5
6
7
8
Steel Pipes  
25  
6
3-way Pipe Fitting  
4-way Pipe Fitting  
Ball Tie Down  
Nylon Base  
6
48  
8
T-stakes  
16  
1
Tarp  
Self-tapping Screws  
42  
PLEASE READ THE FOLLOWING CAREFULLY  
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDEDTHE PARTS DIAGRAM  
INTHIS MANUAL AS A REFERENCETOOL ONLY. NEITHERTHE MANUFACTURER NOR  
DISTRIBUTOR MAKES ANY REPRESENTATION ORWARRANTY OF ANY KINDTOTHE  
BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT  
OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN  
FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL  
REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED  
AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES  
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL  
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER  
INSTALLATION OF REPLACEMENT PARTS THERETO.  
REV 05c, 09e  
SKU 92928  
For technical questions, please call 1-800-444-3353.  
Page 5  
 

Graco Blood Pressure Monitor 288776 User Manual
Grizzly Grinder G1036 User Manual
Grizzly Saw G0457 User Manual
HannsG Computer Monitor HW191AP User Manual
Harbor Freight Tools Vacuum Cleaner 94683 User Manual
HP Hewlett Packard All in One Printer 4MV User Manual
HP Hewlett Packard Webcam 334457003 User Manual
HTC Cell Phone Dash 3G User Manual
Hunter Fan Outdoor Ceiling Fan 23898 User Manual
hussman Saw VGM User Manual