WOOD LATHE STAND
Model 46407
SET up AND OpErATiNg iNSTrucTiONS
Designed for Harbor Freight Tools®
Wood Lathe #36066
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
read this material before using this product.
Failure to do so can result in serious injury.
SAVE THiS MANuAL.
Copyright© 2001 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
cover revised 07i
plications for which this Lathe Stand was designed. Do not modify this Lathe
Stand and do not use this tool for a purpose for which it was not intended.
11. Stay alert. Watch what you are doing, use common sense. Do not use any
Lathe Stand when you are tired.
12. check for damaged parts. Before using any tool, any part that appears
damaged should be carefully checked to determine that it will operate prop-
erly and perform its intended function. Any part that is damaged should be
properly repaired or replaced by a qualified technician.
13. replacement parts and accessories. When servicing, use only identical
replacement parts. Use of any other parts will void the warranty.
14. Do not use Lathe with Stand if under the influence of alcohol or drugs.
Read warning labels on prescriptions to determine if your judgment or re-
flexes are impaired while taking drugs. If there is any doubt, do not use the
Lathe with Stand.
15. Take caution as some woods contain preservatives such as copper
chromium arsenate (ccA) which can be toxic. When cutting these materi-
als extra care should be taken to avoid inhalation and minimize skin contact.
16. Maintenance. For your safety, maintenance should be performed regularly
by a qualified technician.
Warning: The warnings, cautions, and instructions discussed in this instruc-
tion manual cannot cover all possible conditions and situations that may oc-
cur. it must be understood by the operator that common sense and caution
are factors which cannot be built into this product, but must be supplied by
the operator.
Warning! read and follow all of the warnings that came with the Lathe that
you use with this stand.
unpacking
When unpacking, check to make sure the parts listed on page 5 are included. If
any parts are missing or broken, please call Harbor Freight Tools at the number
on the cover of this manual.
SKU 46407
Page 3
Assembly
refer to the Assembly Drawing on page 6.
Note: The only tool necessary is an adjustable wrench. It is advised to always
tighten hardware by hand until the unit is complete, then tighten with the
wrench.
1. Take a Base plate (2) and attach a Leg A (3) to one side of it using four sets
of Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10).
2. On the opposite side of the Base plate (2), attach a Leg B (4) using a set of
Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10).
3. Repeat this procedure with the other Base plate (2) and Legs A&B (3&4) so
that you have two identical leg structures.
4. In the lowest holes of both Legs A&B (3&4) on one leg structure, attach a
Leg Mounting A (5) so that the holes match up and the angled lip is on top.
Secure with two sets of Bolts (7), Spring Washers (9), Flat Washers (8),
and Nuts (10).
5. Repeat same procedure with the other leg structure.
6. Next, you will join the two leg structures allowing the unit to stand. Lay the
units on a flat, level surface so that the insides of both leg structures are
facing each other. Line up the two holes on a Leg Mounting B (6) with the
holes on the inside of one of the Legs A&B (3&4). Secure it with two sets of
Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10). Take the
other end of the Leg Mounting B (6) bracket and attach it to the inside of
the corresponding Leg A&B (3&4) on the other leg structure using two sets
of Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10).
7. Repeat the same procedure on the other two Legs A&B (3&4).
8. Stand up the unit.
9. Lastly, attach an Adapter plate (1) to each Base plate (2) using four sets of
Bolts (7), Spring Washers (9), Flat Washers (8), and Nuts (10).
The stand is ready for your lathe.
Operation
Note: Always use the stand on a flat, level, dry surface. We recommend us-
ing two people to secure the lathe to the Lathe Stand.
1. When mounting a lathe onto the stand, first make sure the mounting holes
on the stand correspond with the mounting holes on the lathe.
2. One person should hold the lathe so that the mounting holes line up, while
the other person puts one of the bolt, washer, nut combinations (not includ-
ed) through one of the holes in an Adapter plate (1), and tighten by hand.
Next, attach one bolt, washer, nut combinations (not included) through one
of the holes on the other Adapter plate (1). Tighten by hand.
3. Now, add the remaining hardware (not included) to secure all of the mount-
ing holes, and tighten with a wrench.
SKU 46407
Page 4
Maintenance
1. Clean dirt, grease, or wood chippings off of the stand with a cloth or brush.
2. Periodically tighten all of the hardware.
parts List
part
1
Description
Adapter Plate
Base Plate
Leg A
Qty.
2
2
2
3
2
4
Leg B
2
5
Leg Mounting A
Leg Mounting B
Bolt
2
6
2
7
24
32
32
32
8
Flat Washer
Spring Washer
Nut
9
10
pLEASE rEAD THE FOLLOWiNg cArEFuLLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER
NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO
THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PROD-
UCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTI-
FIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES
ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
NOTE: Some parts are listed and shown for illustration purposes only and are not
available individually as replacement parts.
rEV 02b
SKU 46407
Page 5
Assembly Drawing
SKU 46407
Page 6
|