FRENCH FRY SLICER
93001
InstructIons and precautIons
saVe these InstructIons. read all
precautIons and InstructIons.
©
®
Copyright 2005, 2009 by Harbor Freight Tools . All rights reserved. No portion of this document or any artwork
contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams within this document may not be drawn proportionally. Due to continuing improvements, actual
product may differ slightly from the product described herein. Tools required for assembly and service may not be
included.
For technical questions or replacement parts, please call 1-800-444-3353.
specIFIcatIons
unpackIng
When unpacking, check to make sure that
the item is intact and undamaged. If any parts are
missing or broken, please call Harbor Freight Tools
at the number shown on the cover of this document
as soon as possible.
Cutting Sizes
1/2” Square x 25 holes
Suction Cup Base
Mounting
Revised Manual 09k
3. Slide the Cutting Blade Frame (2) all the way
down with the sharp edges facing inward.
See Figure 2, below.
Push Block
(3)
1/2” Cutting
Blade
Frame (2)
Figure 4
7. Lift the Handle all the way up and place
a potato, or other soft vegetable, into the
working area of the unit. See Figure 5, below.
Figure 2
4. Push the blade lock down over the Cutting
Blade Frame (2), locking the Frame in place.
5. Place the plastic Push Block (3), with the open
side of Tabs facing down, onto the back end
of the unit so that the tabs on the back of the
Push Block fit through the holes on the end
frame. See Figure 3, below.
WARNING! Keep fingers and hands away from
the cutting area of the unit.
8. Press down on Handle slowly and firmly with
both hands to cut the potato. Remove slices
while Handle is still in the down position.
cleanIng
1.
2.
Remove Cutting Frame (2) and Push Block
(3).
Push Block
(3)
Wash Cutting Frame and Push Block in
dishwasher or by hand using hot water and
detergent.
Figure 3
3.
Wipe off the rest of the Base (1) using a
clean damp cloth with light detergent. Wipe it
dry after cleaning.
6. Turn the Lock Lever on the back of the end
frame, locking the Push Block (3) in place.
See Figure 4, above right.
93001
For technical questions, please call 1-800-444-3353.
Page 3
parts lIst & assemBlY dIagram
part
description
Qty.
1
2
3
4
5
Base
1
1
1
1
1
1/2” Cutting Blade Frame
Push Block
Handle
Suction Lever
4
5
1
2
3
please read the FolloWIng careFullY
THeMANUFACTUReRAND/oRDISTRIBUToRHASPRovIDeDTHePARTSLISTANDASSeMBLyDIAgRAMINTHISDoCUMeNT
AS A ReFeReNCe TooL oNLy. NeITHeR THe MANUFACTUReR oR DISTRIBUToR MAKeS ANy RePReSeNTATIoN oR
WARRANTy oF ANy KIND To THe BUyeR THAT He oR SHe IS qUALIFIeD To MAKe ANy RePAIRS To THe PRoDUCT,
oR THAT He oR SHe IS qUALIFIeD To RePLACe ANy PARTS oF THe PRoDUCT. IN FACT, THe MANUFACTUReR AND/
oR DISTRIBUToR exPReSSLy STATeS THAT ALL RePAIRS AND PARTS RePLACeMeNTS SHoULD Be UNDeRTAKeN By
CeRTIFIeD AND LICeNSeD TeCHNICIANS, AND NoT By THe BUyeR. THe BUyeR ASSUMeS ALL RISK AND LIABILITy
ARISINg oUT oF HIS oR HeR RePAIRS To THe oRIgINAL PRoDUCT oR RePLACeMeNT PARTS THeReTo, oR ARISINg
oUT oF HIS oR HeR INSTALLATIoN oF RePLACeMeNT PARTS THeReTo.
record serial number here:
note:If product has no serial number, record month and year of purchase instead.
note:Some parts are listed and shown for illustration purposes only, and are not available individually as
replacement parts.
93001
For technical questions, please call 1-800-444-3353.
Page 4
|