6’ x 6’ Greenhouse
97439
set up and Maintenance instructions
®
distributed exclusively by harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
saVe this Manual.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Manual reVised 08h
snow or other debris can cause parts
of this greenhouse to buckle sud-
denly. Do not allow snow or debris
to accumulate on top of the green-
house. NEVER enter a greenhouse
with accumulated debris on top.
unpackinG
When unpacking, check to make sure
that the item is intact and undamaged. If
any parts are missing or broken, please
call Harbor Freight Tools at the number
shown on the cover of this manual as soon
as possible.
4. Assemble the Greenhouse in a
smooth, level area that is sheltered
from the wind.
5. High winds can tear the Greenhouse
loose from the Spikes and could
result in property damage or personal
injury. In case of severe weather or
high winds, take the Greenhouse
apart or move it under cover.
6. This product is not a toy. Do not al-
low children to play with or near this
item.
7. Use for intended purpose(s) only.
8. Inspect before use; do not use if parts
loose or damaged.
9. Maintain product labels and name-
plates. These carry important safety
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.
10. The warnings, precautions, and in-
structions discussed in this instruction
manual cannot cover all possible con-
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
saVe these
instructions.
SKU 97439
For technical questions, please call 1-800-444-3353.
Page 3
Figure for pole assembly (steps 4-6)
asseMblY instructions
read the entire iMportant
saFetY inForMation section
at the beginning of this manual
including all text under
subheadings therein before set
up or use of this product.
note: For additional information regarding
the parts listed in the following pages,
refer to the Assembly Diagram near
the end of this manual.
4. Fit the covered Rafter Slats into the
grooves in the Rafter Poles (G) and
slide into place, with the holes on the
Rafter Poles facing toward you (see
insets above).
note: The Greenhouse is heavy and
unwieldy when fully assembled. It
should be assembled near the area
where it will be anchored. The area
should be firm, level, and provide
shelter from the wind.
5. Fit the covered Side Slats into the
grooves in the Side Poles (H) and
slide into place, with the holes on the
Side Poles facing toward you.
Figure for slat assembly (steps 1-3)
6. Fit the covered Bottom Slat into the
groove in the Bottom Pole (F) and
slide into place, with the holes on the
Bottom Pole facing toward you.
Figure for connector ass’y (steps 7-8)
1. Slide two Rafter Slats (O) into the
sleeves on the top of the Front Panel
(K).
2. Slide two Side Slats (P) into the
sleeves on the sides of the Front
Panel.
3. Slide Bottom Slat (Q) into the sleeve
on the bottom of the Front Panel.
7. Secure the Rafter Poles together at
the peak of the roof using Connector
A. Make sure the unconnected point
on the Connector faces towards you.
SKU 97439
For technical questions, please call 1-800-444-3353.
Page 4
8. Secure both top corners using a
Connector B on the left side and a
Connector C on the right side, again
make sure the unconnected point on
the Connectors face towards you.
Figure for bar installation (steps 13-14)
9. Secure the bottom left-hand corner
of the Panel with Connector D. Use
the Hex Wrench (T) to fasten a Hex
Screw (S) into the hole on the bottom
of the Bottom Pole.
10. Secure the bottom right-hand corner
of the Panel with Connector E. Use
the Hex Wrench (T) to fasten a Hex
Screw (S) into the hole on the bottom
of the Bottom Pole.
11. Repeat the above steps to assemble
the Rear Panel (L).
13. Insert Rafter Bars (I) into the Sleeves
at the top of the Body Panel (M).
Figure for panel assembly (step 12)
14. Insert Side Bars (J) into the Sleeves
at the sides of the Body Panel (M).
12. Line up the Connectors on the Front
and Rear Panels and connect to the
Body Panel (M). The uppermost pole
in the Body Panel should be turned
with the connection downward. All
other poles should be turned with the
connection upward, as shown.
SKU 97439
For technical questions, please call 1-800-444-3353.
Page 5
to the ground. Use the two remaining
Stakes to secure the door flap.
Figure for bar connection (steps 15-19)
Maintenance and
serVicinG
1. Periodically, inspect the general con-
dition of the product. Check for loose
screws cracked or broken parts, and
any other condition that may affect
its safe operation. If any defects are
found have them repaired or the parts
replaced immediately.
2. Clean external surfaces of the prod-
uct with clean, moist cloth.
15. Find the holes in the Bars (I, J) and
line them up with the holes in the
Poles (G, H).
16. Secure the Bars (I, J) to the Poles
(G, H) using four Screws (R) per Bar.
The Screws will be threaded directly
through the cloth surrounding the
Bars.
17. Choose an area for the Greenhouse
that is flat, level and free of debris. If
possible place the Greenhouse in an
area that is sheltered from the wind.
High winds can tear the Greenhouse
loose from the Stakes (N) and could
result in property damage or personal
injury. In case of severe weather,
take the Greenhouse apart.
18. Examine the area where the Green-
house is to be placed. Make sure
there are no utility lines beneath the
surface that might be damaged by
the Stakes.
19. Hammer the Stakes (N) into each
corner of the Greenhouse to secure it
SKU 97439
For technical questions, please call 1-800-444-3353.
Page 6
please read the FolloWinG careFullY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLy
DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE MANUFACTURER OR
DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy OF ANy KIND TO THE BUyER THAT
HE OR SHE IS QUALIFIED TO MAKE ANy REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANy PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR ExPRESSLy STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD
BE UNDERTAKEN By CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE
BUyER ASSUMES ALL RISK AND LIABILITy ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
parts list
part
A
description
Connector A
Qty
2
part
K
description
Front Panel
Qty
1
B
Connector B
Connector C
Connector D
Connector E
Bottom Pole
Rafter Pole
Side Pole
2
L
Rear Panel
Body Panel
Stake
1
C
D
E
2
M
N
1
2
6
2
O
P
Rafter Slat
Side Slat
4
F
2
4
G
H
I
4
Q
R
Bottom Slat
Screw
2
4
32
4
Rafter Bar
4
S
Hex Screw
Hex Wrench
J
Side Bar
4
T
1
SKU 97439
For technical questions, please call 1-800-444-3353.
Page 7
asseMblY diaGraM
M
l
record product’s serial number here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 97439
For technical questions, please call 1-800-444-3353.
Page 8
|