Hamilton Beach Fan MCRES 525 User Manual

PARTS LIST – BARBED ADAPTERS ARE SOLD SEPARATELY  
Parts  
QTY  
PARTS  
QTY  
MCRES-525™ Reservoir  
Fill-cap & o-ring  
1
1
Retention screws  
Port plug  
4
1
This product is intended for expert users. Please consult with a qualified technician for installation. Improper installation may result in  
damage to your components. Swiftech assumes no liability whatsoever, expressed or implied, for the use of these products, nor their  
installation. The following instructions are subject to change without notice. Please visit our web site at www.swiftnets.com for  
updates.  
The MCRES-525™ reservoir is designed to be installed in a 5 ¼” drive bay. It features three 3/8” threaded ports (standard NPT thread)  
to accommodate a number of configurations (see * Swiftech fittings). The port usage is defined as follows:  
(1) Discharge port located at the “stepped-down” compartment. This port must ALWAYS be connected to the  
pump inlet for the MCRES-525™ to operate properly.  
(2) Inlet ports can be used interchangeably: in “single inlet” configuration (the most common), or “dual inlet”  
configuration when devices are returning to the reservoir in parallel. One port plug is provided to seal one of the  
inlets in order to accommodate the most common “single inlet” configuration.  
Installation of the fittings requires sealant. Recommended sealants include Teflon pipe dope or solvent cement  
(Goop), which are the easiest to use; Teflon tape will require three to four turns for a good seal. Tighten fittings  
until firm, do not make up to the nut interfering with the threaded hub - a thread should be visible on the fitting. Use  
of silicone sealants is not recommended.  
The following guide assumes that all liquid cooling components in your system, such as radiator, pump, and water-block(s) have been  
already installed, and the graphic below shows an overview of a typical installation.  
Swiftech Fittings & Spare parts  
Important! All fittings (except DP-11) require sealant: plumbers tape, or plumbers goop (preferred)  
PI011623S  
DP-11  
P6N  
A6-8  
A6-6  
1/2" barb to 3/8" NPT, for 1/2"  
Inner diameter tubing (3/4" or  
5/8" outer diameter) – Order  
Separately  
3/8" barb to 3/8" NPT, for  
3/8" Inner diameter tubing  
(1/2"outer diameter) – Order  
separately  
3/8” NPT to ½” tube (outer  
diameter) quick-connect  
fitting – Order separately  
Fill-cap & o-ring  
3/8” NPT Port  
plug  
Included  
Included  
Copyright Swiftech 2004 – All rights reserved – Last revision date: 1-25-05  
Rouchon Industries, Inc., dba Swiftech – 1703 E. 28th Street, Signal Hill, CA 90755 – Tel. 562-595-8009 – Fax 562-595-8769 - E Mail:  
[email protected] – URL: http://www.swiftnets.com - Information subject to change without notice  
 

GPX Stereo System HM3817DTBLK User Manual
Graco Model Vehicle GS35 User Manual
Grizzly Paint Sprayer G0533 User Manual
Haier Washer slim3 User Manual
HannsG Computer Monitor HW191AP User Manual
Harbor Freight Tools Air Compressor 47065 User Manual
Heath Zenith Home Safety Product 2LBN2 User Manual
HP Hewlett Packard Portable Generator 8082A User Manual
Husqvarna Chainsaw T425 User Manual
IKEA Indoor Furnishings AA 83594 2 User Manual