Mini Sea-ox
User' Manual
Haier Household Electric Water Heater
FCD-8
Group
Qingdao Economic & Technical Development Zone
Haier Water Heater Co.,Ltd.
Please read this manual before usage
Retain it for future reference
Usage
Before Usage
Dear users,
After installation, as there's no water inside the tank, please be sure to open
the water inlet valve and any of water exit. When the tank is filled with water
and the water exit keeps discharging water, close the valve. Check if there's
water leakage at each joint. Plug the power plug. In usage, be sure to open
the cold water valve before the hot water valve to avoid scalding .You can
turn the handle of the mixing valve upward to the left then pull the handle of
the safety valve to discharge the water.
Thanks for choosing Haier water heater product.
Haier products have good quality and excellent performance. To facilitate
you to use the product, please read the manual and operate accordingly.
Please retain it for future reference.
The international star service of Haier Group will always accompany you.
No matter what kind of problems you meet in usage, please contact with the
local after -sales service agent. We are at your service all the time. Thanks
again for choosing Haier Product.
Switch on the power. The heating indicator is on. The water heater starts
operating. When the water temperature reaches 60 , the heating indicator is
off. The water heater will stop heating and enters heat preservation mode.
If the water temperature drops to certain degree, the red indicator will light on
again to continue heating. It will circulate like that to guarantee the continuous
hot water supply.
The water heater you purchased may not fully comply with the figure in
the manual due to the improvement of product. We apologize for the
inconvenience occurred therefrom.
Features
1.Safely:
Hai-quality heat proof stainless steel electric heating element, safe and
Reliable; overtemperature protection; overpressure protection of tank;
2. Durability:
Attention
Full plastic shell, elegant and durable;
Enamel tank, with more reliable quality and longer operation life.
3. Multi- usage:
This product requires power supply with 220V , 50Hz.
The max heating temperature is 60 , not drinkable.
Enclosed structure, capable of supplying multiple places;
Suitable for family , enterprise, catering, beauty service etc. on hot water
Supply.
Reliable earthing is requested. Earthing wire shall be separated from neutral
wire strictly. To avoid accident, the positions of the live wire and earthing
wire can not be replaced.(See to Figure 5.)
4. Nice molding, space-saving
Arc appearance, appealing design, dapper and elegant.
5. Convenience:
60 thermostatic heating. It will stop heating when the temperature
Live wire
Earthing wire
Earthing wire
Earthing wire
Reaches 60
.
(Figure 5)
Parameters
Live wire
Live wire
Live wire
Earthing wire
Neutral wire
Neutral wire
Rated voltage:220V~50Hz
Power: 1200W
Dimension(See to Figure 1)
Weight: (See to Figure 1)
Rated pressure: 0.75MPa
Waterproof grade: antisplash(
Volume: (See to Figure 1)
)
Tap water pressure: no less than 0.05MPa
5
2
Installation
Dimension Figure
Figure 1
Be sure to have it installed by the appointed staff. It adopts wall-mounting installation.
First decide the installation location according to the usage requirement. Make two
holes in the wall with depth 70mm and 9mm by churn drill as per the indication of
installation diagram.
Front view
a1
Cutaway view
Side view
Fasten the wall-mounting plate on the wall tightly with two expansion bolts as per
indicated in Figure 2. Check and confirm that the bolts are not loose.
Hang the water heater vertically onto the wall by the wall-mounting plate. Confirm it
is firmly mounted. Please reserve certain space for the future maintenance during
installation.
F
(Figure 3)
b1
(Figure 2)
E
D
d1
Wall-mounting
plate
Expansion bolt
B
B
c1
Connect to drain hose
A Hot water outlet
B Cold water inlet
C Mg anode rod
D Heating element
E Enamel tank
Net
weight
When the power is switched on, and the water heater starts operating, there may
be some water discharged from the pressure relief hole of safety valve. It is due to
the water expansion under heating, and is normal phenomenon. The pressure
relief hole shall communicate with the air directly. Do not block it. If the water
heater will be installed in the bathroom without sewer, we suggest you add drain
hose. Fasten the drain hose to the drain thread of safety valve by twisting (see to
Figure 3). According to the need, you could truncate or elongate the hose in your
favor. Connect the other end of drain hose to the sewer to avoid polluting the
room by splashing. The drain hose connecting to the safety valve shall be kept
downward sloping in installation and in a frost-free environment.
Model
FCD-8
Volume
8L
d1
a1
b1
c1
8kg
414mm 100mm
255mm
325mm
F Wall-mounting bracket
Remarks:the petmitted error limit of above parameters is 10%.
Schematic Diagram
Be sure to check and confirm that the tank is filled with water, there's no leakage
at each joint and the power supply complies with the stipulation before switching
on the power.
L:Brown wire
N:Blue wire
MT
BT
MT:High temperature limiter
(Figure 4) for reference in installation only
EH:Heating element
EH
L
E:Yellow/green wire
HL
E
N
Hot water outlet
BT: Thermostat
Safety valve
HL:Heating indicator
E
Cold water inlet
3
4
|