Haier Washer Dryer WNA500T User Manual

Haier  
AUTOMATIC DRUM  
WASHING MACHINE  
WNA500T WNA600T  
INSTRUCTIONS FOR  
INSTALLATION AND  
OPERATION  
 
FUNCTION INTRODUCTION.....................................................3-5  
INSTALLATION...........................................................................6-8  
CLOSE UP................................................................................9-11  
USINGINSTRUCTIONS..........................................................12-16  
MAINTENANCE...........................................................................17  
SOLUTION TO PROBLEMS................................................18-19  
ATTACHEDCHART:  
GUIDE FORSELECTIONGPROGROMME...........................20-21  
WARNING....................................................................................22  
2
 
FUNCTION INTRODUCTION  
FUNCTION COMPARING TABLE  
MODE  
WNA600T  
WNA500T  
FUNCTION  
5
5
Washing capacity  
Programmes  
16  
16  
Cotton  
Synthetic  
Wool  
Thermostat ajustable(0-90 C)  
Cold wash button  
Economic wash button  
No soak  
Spin speed  
500r/min  
600r/min  
Power switch  
ON/OFF  
Rinse  
Plustic tub  
Door-locking device  
Power  
330W  
650W  
67Kg  
330W  
650W  
67Kg  
Power(Wash)  
Power(Spin)  
Weignt  
H.W.D  
850X520X595  
3
 
FUNCTION INTRODUCTION  
Characteristics of WNA600T WNA500T  
EuropeanandAsiaAesthetic design, elegantandbeautiful.  
Three types of wash: rinse, beat and rain effect.  
Changeablewashingfunction:cold washandhotwash,Nosoak  
Threetypesoflaundry:cotton, syntheticandwool, with16cycles.  
Alargewashingcapacity:5kg.  
Stainless steel drum; painted cabinet with three layers of  
cataphresis, phosphorus and paint.  
Rinse with anti-crease system, care for clothes.  
Super anti-shock design.  
Self-lock device for the door.  
4
 
Installation  
Unpacking  
levelling and  
positioning  
Remove the package and check that the machine is  
undamaged.  
If you have any doubts, do not use the machine and call on a  
qualified technician. Keep all packing parts (plastic bag,  
foam rubber, screws etc.) out of the reach of children since  
theycouldbedangerous.  
Important: The inside of the washing machine which  
consists of a floating unit, is fixed with screws at the back of  
the cabinet (Fig.1) during transport. Before starting the  
machine remember to release the floating unit by removing  
the above screws . To prevent water spray from entering the  
machine, remember to close the holes left open by the  
screws with the plastic caps provided in the packet  
containing the owner's manual. And rescrew the holes  
where the iron piece is taken down with the former two  
screws.Attention:keep the packing screws and plastic caps  
in a safe place for later use. It is important for the machine to  
be perfectly level (the angle of inclination on the work surface  
must not be more than 2 degrees). For this reason the  
machine is fitted with adjustable feet used for levelling the  
machine before use (Fig.2). In the case of flooring with  
carpeting, remember to check that the ventilation in the  
support area is not plugged.  
Fig.2  
Fig.1  
6
 
Installation  
Connect the plug to a socket provided with efficient earthing.  
Electric  
connection  
Or use the spare earthing wire supplied together with the  
machine and the earthing terminal located on the left-upper  
corner of the back of your machine (Warning: this appliance  
must be earthed as a safety measure according to the law).  
Make sure that the voltage and frequency available  
correspond with the values stated on the data plate located at  
the back of the machine (power range:187-242V) and that the  
electric system is dimensioned to withstand the maximum  
current shown on the data plate. If the socket the machine is  
connected to does not correspond with the plug, replace the  
plug with a suitable one and avoid using adaptors or shunts  
since they could cause overheating and burn out.The spare  
eathing wire is absolutely not allowed to be connected to  
water pipe,heating pipe or other kinds of pipes.  
Connection  
of tap and  
Loading  
Hose  
Connect the inlet hose to a cold water tap with a 3/4 gas  
threaded opening, and fit the filter and the rubber gasket  
supplied with the washing machine. Check that it is tightly  
screwedtothetap(Fig. 3).  
Fig. 3  
If the water piping is new or has not been used for a long time,  
before making the connection, let the water run until it is clear  
andfreefromimpurities.  
This step is necessary to ensure that the incoming water  
doesnotclogandpossiblydamagethemachine.  
7
 
Installation  
Connection of  
the Drain Hose  
Connect the drain hose to a drain duct (with internal  
diameter of at least 4 cm.) or place it for drainage into  
a sink or a tub, ensuring that there are no kinks or  
bends. The free end must be at a height of between  
80 and 100 cm. Should it be necessary to fix the end  
of the hose at a height of less than 80 cm from the  
floor, the hose must be fixed in the appropriate hook  
on the upper part of the back panel (Fig.4) or use the  
suppliedsupporttofixthedrainhose.(Fig.5)  
Fig.5  
Fig.4  
Insert stainless steel screen washers into end of each  
supply hose and attach that end of supply hose to  
your 3/4" water tap spigot.Be sure that you match up  
cold water to "C" .Note:Home Centers also have"Y"  
connectors and "Couplings" which enable you to  
connect the machine to your sinks faucet.  
Connecting  
WaterSupply  
8
 
Close up  
G
D
E
B
A
F
C
 
Close up  
A Programme selector Knob.  
By turning this dial (clockwise only) you can  
select from sixteen wash programmes the one  
mostsuitedforyourwashing.  
1~7 cotton cycle  
8~12 synthetic cycle  
13~16 wool cycle  
B Programme selector Knob.  
With this dial you can set the wash temperature  
that you desire.For synthetic and wool, the  
thermostat works below 60¡æand 40¡æ  
respectively.  
30  
MAX  
80  
40  
70  
50  
60  
When the dial is located at " ", a cold wash is  
available  
C Power Light  
This light indicates whether the electricity is on or  
off. The light comes on when button D is pressed  
andgoesoffwhenbuttonDisnotpressed.  
D ON/OFFButton  
ON/OFF button. Supplies electrical power to the  
machine.  
E EconomicWashButton.  
It reduces water and power consumption when  
rinsingifthemachinedoesnothaveafullload.  
(Lessthan3kg)  
10  
 
Close up  
I NoSoakButton  
For the synthetics cycle and the wool cycle, push the  
button down, the anticrease funtion will be skiped and  
automatically enter into the next step;Release the  
button, theanti-creasefuntionwillworkagain.  
G Detergent Dispenser.  
The detergent dispenser is divided into 4 compart-  
mentsmarked1,2,A,C:(SeeFig.8)  
1Pre-washdetergent  
2Washdetergent  
ASofteners, conditioners, perfumes  
CBleach  
A
C
2
1
Fig.8  
11  
 
Using instructions:Your machine  
offers the best results when...  
In order to get the excellent results that you would expect  
The weight  
is right  
from your washing machine, it is important to load the washer  
correctly. You should therefore choose the quantity of each  
typeoffabricthatyouwanttowash. Thistablewillhelp:  
Colour fast fabrics  
Delicate fabrics  
Woollens  
maximum load 5 kgs/11lbs  
maximum load 2 kgs/2.5 lbs  
maximum load 1 kg/2.2 lbs  
maximum load 2.5 kgs/5.5 lbs  
Mixed fabrics  
Divide the laundry by fabric and degree of soiling loaded  
makingtheloadsasuniformaspossible.  
Pullthehandleout toopenthedoor.  
Laundry has  
been loaded  
correctly  
Place the laundry in the machine remembering to arrange  
uniformly.  
12  
 
Using instructions:Your machine  
offers the best results when...  
The correct  
A perfect wash depends above all on choosing the most  
programme has suitable programme. We would therefore advise you to  
been chosen  
divide up your washing into separate loads of more or  
less the same types of fabric. This will make it easier to  
selectthebestprogramme.  
Hints on choosing the programme are shown in the table  
onpagesofthismanual.  
Onceyouhaveselectedaprogramme, justturndial  
A clockwise until the chosen programme lines up with  
theindicatorlineonthefaciapanel.  
Anti-crease  
When your machine is washing synthetic fabrics or  
woollens, the wash cycle stops before the last spin cycle,  
with the laundry soaked in water in order to prevent the  
formation of creases due to spinning. Complete the  
wash cycle with a spin cycle or simply drain the water  
fromthewashingmachinewithoutspinning.  
For the spin cycle, turn the selector knob Aclockwise by  
onestep.  
To drain, set the selector knob Aon drain programme in  
both cases, before turning the knob A remember to  
switchOFFtheON/OFFbuttonD.  
13  
 
Using instructions:Your machine  
offers the best results when...  
The detergent  
has been put  
in properly  
The 4 compartments marked 1, 2, Aand C (Fig.9) should  
beusedasfollows:  
1Pre-washdetergent  
2Washdetergent  
A Conditioner,starch, scents  
C Bleach  
A
C
2
1
Fig.9  
Remember that it is important to use the right amount of  
soap powder or liquid for the type of laundry you are washing;  
the amount of detergent you use depends on a number of  
factors:  
Water hardness; if the water in your area has a  
high calcium content, we recommend using a  
anti-limestone additive.  
degree of dirtiness; increase the amount of  
soap powder used in the case of heavily soiled  
laundry.  
laundry load; the smaller the load the less soap  
powder you will need to use.  
14  
 
Using instructions:Your machine  
offers the best results when...  
Thefollowingtablewillguideyou:  
Compart.1 Compart.2  
prewash  
Laundry  
Compart.A Compart.C  
wash  
Normally 1/2 measuring 1 and 1/2  
Softeners  
Bleach  
soiled  
cup  
measuring (see note 'A') (see note 'C')  
cups  
When using concentrated detergents, remember to keep to the  
manufacturer's instructions using only the measuring cups  
suppliedwiththepacket.  
Use more detergent in the case of very hard water ( more than  
21.F), but remember to maintain the proportion between the  
prewashandwashcycles.  
Liquiddetergent  
The liquid detergents currently available on the market may be  
used with the washing machine. Use compartment 2 for very  
dense liquid detergents. Follow the manufacturer's  
instructions when using liquid detergents sold with the ball  
detergent dispenser. Place the ball dispenser in the tub of  
washing machine together with the laundry.  
The prewash cycle may not be used with liquid detergents.  
Note "A"  
For soft and fluffy laundry always a softener in the final rinsing  
cycle.  
Note"C"  
Bleach is ideal for removing stains (e.g.tea, coffee, fruit, red  
wine ) on resistant fabrics like cotton, hemp and linen provided  
the wash care label indicates that the garment may be  
bleached.  
Place the bleach in compartment C before you start the  
machine without exceeding the maximum level. your machine  
will load the bleach automatically when necessary .when  
necessary.  
Never place bleach in the other compartments.  
15  
 
Using instructions:Your machine  
offers the best results when...  
You can now start washing. We would advise you, especially  
The cycle is  
started  
the first few times, to check that the programme that you  
have set is really the one you want and that the fabric  
selectioniscorrect.  
If you want to start the cycle immediately, press the ON/OFF  
buttonD.  
At the end of the chosen cycie, the machine will stop  
automatically.  
The wash is  
finished  
Press the ON/OFF button D to switch off the power (light C  
willturnoff).  
16  
 
Maintenance: five simple  
precautions for this machine  
Your machine is designed to last without complicated  
maintenance.  
All the same, we would ask you to take care of a few small  
matters. If you follow these four simple rules, we are sure that  
the washing machine will stay as your faithful friend and  
helperforalong, longtime.  
1. Ensure that your machine was installed according to the  
installation manual that comes with this booklet.  
2. Avoid at all costs using solvents either to clean the  
machine, or to do the wash. when clean the machine, cut  
offthepower.  
3. Clean the detergent dispenser every so often. This is very  
simple and should be done with water. Your machine has  
an extractable dispenser to make it even easier. Just pull it  
upwards and out.  
4. If it is long time no use, you'd better cut off the power,  
switch off the tap, and open the door to avoid unpleasant  
smell.  
5. Your washer is equipped with a self-cleaning pump. It is  
therefore not necessary to carry out cleaning and  
maintenanceoperations.  
Open the cover of the filter, loosen the knob in counter-  
clockwise rotation, then take out the filter and clean it with  
water, everymonth.(seeFig.8)  
Fig.8  
Note: Reassembly the filter carefully after cleaning,  
ensuring it is fit perfectly and no water can come out.  
17  
 
Solution to Problems  
Even though your washing machine has been carefully  
designed and constructed, something could still go a miss  
with your machine. Before rushing to phone one of our  
service centres, however, please check that the operations  
listed below have been carried out. In many cases you will  
save time, money and bother. Our statistics show that many  
of the calls received by our service centres could have been  
avoidedwithjustalittlemoreattention.  
Checkthat:  
The washing  
machine  
won't start  
theplugispushedrightintothemainssocket;  
thedoorisclosedtightly:  
the "ON/OFF"buttonhasbeenpressed.  
Checkthat:  
thetapisopenandproperlyconnectedtotheinlet  
The washing  
machine won't  
fill with water  
pipe;  
theinletpipeisnotbent.  
The machine  
fills and drains  
continuously  
Checkthat:  
thedrainpipeisplacedatleast80cm/32inches  
above ground level.  
The machine  
will not drain  
drain the water  
Check that:  
thedrainpipeisnotblocked;  
thedrainpipeisnotconnectedataheightmorethan  
1 metre/40inchesabovegroundlevel.  
There is too  
much foam in  
the tub  
Checkthat:  
thedetergentbeingusedismeantforautomatic  
machinesandnotforwashingbyhand;  
thattheamountusedisthatshowninthismanual  
and not more.  
18  
 
Solution to Problems  
Check that:  
The machine  
vibrates too  
much when  
spinning  
thetransitboltshavebeenremoved(see  
installation manual);  
themachineislevel;  
thewashingloadisaccordingtotheinstructions  
given in this booklet.  
Check that:  
thereisasuddenpowerfailureorwaterstop.  
themachineisinthenormalstateofrinse.  
The machine  
stops operating  
before finishing  
19  
 
Guide for selecting programme  
21  
 
Warning:  
1. If the supply card is damaged, it must be replaced by a special  
card or assembly available from the manufacturer or it is service  
agent.  
2. It a stationray appliance is provided with a supply card and a plug,  
the instructions shall state that the appliance must be positioned  
so that the plug is accessible.  
Note: this requirement dose not apply if the appliance incorporates  
other means for disconnection from the supply.  
3. For washing machines with ventilation openings in the base, that a  
carpet must not obstruct the openings.  
4. The instructions shall state that the appliance is to be connected  
to the water mains using new hose-sets and that old hose-sets  
should not be reused.  
Note: this instructions is not required if the hoses are permanentiy  
attached to the appliance.  
22  
 
WIRING CIRCUIT (WNA500T WNA600T)  
I3=NO SOAK  
I2=ECONOMIC WASH  
I1=ON/OFF  
L Line  
P2 2- level pressure switch  
N Neutrol  
SL Line LED  
MT Timer motor  
RR Heating element  
SO Door lock  
PS Drain pump  
MR Thermol lock  
TH40 40 C thermostat  
EVF Cold water electrovolve  
P1 1- level pressure switch  
 

Graco Stroller PD137548A User Manual
Grizzly Power Roller G5771 User Manual
Harmar Mobility Mobility Aid AL003 User Manual
Hasbro Games Magic Mirror Card Game User Manual
Hotpoint Range RB790SD User Manual
HP Hewlett Packard Printer 2280TN User Manual
HP Hewlett Packard Server BL685c User Manual
Husqvarna Utility Vehicle HUV 4213 G User Manual
IBM Network Card LPCI COM232 4 User Manual
IBM Switch S05L 1270 01 User Manual