Double Drive Fully Automatic Washing Machine
User's manual
This manual is for
HWM65-828
Please read this manual
carefully before using.
Retain it for future reference.
Names of the parts
Trouble-shooting answer to question
(If there's breakdown, please pull off the power plug before checking) The following phenomena are
not breakdowns sometimes.Please confirm again before sending it to repair. If there are real
breakdowns, please come to the special maintenance department or after-sale service department
of our company. Do not repair it by yourself..
Top lid component
Phenomena
The reason
How to settle
Inner cover
Water absorption gasket
Outer tub cover
Detergent box
The digitron displays E0.
The top lid is opened during reserve procedure.
Close the top lid.
Screw cover
Control panel seat
Soften inlet
The drainage cannot work, or is too slow.
The digitron displays E1.
Is the drain hose put down?
Is the drain hose blocked?
Put down the drain hose. Open and close the top lid once.
Clean the foreign material. Open and close The top Lid Once.
Inner tub
Water inlet valve
Balance ring
It stops running in midway. The digitron
displays E2.
Cabinet handle
Drain hose
Power cord
Hook
Close the top lid.
The top lid is not closed.
Filter cover
Lint filter
The safety switch acts, and the
spinning cannot work. The
digitron displays E3.
Reorder the laundries. Close the top lid.
The machine will start running after 10
seconds of being placed horizontally.
Pulsator
Are the laundries put slantingly?
Is the machine slanting?
Attach block
Open the water tap. Open and close the
top lid once.
Clean the water inlet valve.Open and close
the top lid once.
Open and close the top lid once.Use until
the water pressure is normal.
Is the water tap opened, or is there water
supply failure?
Is the water inlet valve blocked?
Is the water pressure too low?
The water filling does not work,
the digital displays E4.
Drain bushing
Drain protective lid
Adjustable foot
Back cover
Base frame
Cabinet
Please contact the after-sales
service department.
The digitron displays E6.
The water level sensor is bad.
Adjustable foot label
Fixed foot(3)
Is there power failure?
Is the power plug inserted tightly?
Is the water level reached preset position?
Please use it when there's power supply.
Insert the power plug tightly.
Fill water to the preset position.
Not wash
The machine does
not act
Is the power plug inserted tightly?
Is the top lid closed reliably?
Are the laundries set flat?
Insert the power plug tightly.
Close the top lid.
Set the laundries flat.
Not spin
Meaning and description of the symbols
Adjust the machine to be even
Reorder the laundries and close the top lid.
Remove the foreign materials.
Is the machine slanting?
Are the laundries put slantingly in spinning?
Are there any foreign materials?
There's abnormal sound
inside the machine
Contents marked with that symbol are related to the
Warning sign
Is the screw of the jointer of water
inlet hose loose or awry?
safety of the product and the personal safety of the users.
Please operate in strict conformity to the contents.otherwise
it may cause damage of the machine or injure the personal
safety of the user.
The water tap leaks
Fasten the screw of the jointer properly.
Common phenomena
Phenomena
Explanation
Balance the laundries to avoid slanting.
The spinning is intermittent when it starts.
The wash procedure is paused.
Forbidden sign
Contents marked with that symbol are actions forbidden
The cloth sensor is checking the cloth, it will add water after 48 seconds.
to perform. Performing of those actions may result in damage of
the machine or influence the personal safety of the user..
The program is setting the drain time. Some time is needed
before it starts spinning.
Push the PROGRAM button to select SPIN,
but it doesn't work.
The pulsator pauses during water inlet
in wash and rinse.
It is to avoid splashing during water inlet.
There may be some water flowing out of the
drain hose in the first use of the machine.
It is the water remained in the factory inspection of performance.
1
Safety precautions
Disposal after washing
After using, please clean the lint and foreign materials of the lint filter etc. in time.
Otherwise it may influence your using the machine.
The washing machine must be positioned so that
the plug is accessible. Be sure to pull the plug off
and close the water faucet in following cases:
power failure, delivering the machine, setting the
machine idle or cleaning the machine. Do not plug
or pull the power plug with wet hand.
Please plug the power plug on special
receptacle. Be sure to use three-pins
power receptacle. Ensure that the earthing
prong of the power receptacle is earthed
reliably. Use leakage protector if possible.
Please first pull off the power plug from the receptacle before cleaning.
The lint filter must be used during washing.
It must be cleaned in time after each using.
Lint filter:
1.Push down the spring piece of the top lint filter
to make the claws out of the filter cover, and then
pull out the lint filter to get it down. figure1
2.Pull the back of the lint filter, and then you can
get down it off the front cover of the lint filter. figure2
3.Sweep the rubbish in the lint filter.
Clean the detergent box and set it on
the control panel seat.
1.The method of dismantle: Push it up aslant and gently.
2.The method of install : install it upwards and aslant
and push it in .
Do not bend ,extend, twist, bind by force. Do not press or nip it with weight.
Keep the pin of the power plug clean, if the power plug is polluted with dust, please wipe with
dry cloth carefully.
If the power cord or the power plug is bad, to avoid risk it is required to have it replaced by
the technicians of our special shop or our customer care agent.
4.Put the back of the lint filter into the front cover .
5.Put the lint filter into filter cover, and make it
tight .
6.Make sure the lint filter well installed, or it can
influence your use.
In case the washing machine is installed on ground with
carpet, do not block the ventilation hole with carpet.
Do not use water hotter than 50
.
The back cover of lint filter
Up
Up
Dismantle
Install
The ventilation
holes at the bottom
Dismantle
Dismantle
Install
Install
Down
Carpet
The front cover of lint filter
Figure 2
Down
Figure 1
The filter screen of the water inlet valve is likely to be
blocked by foreign materials and influence the water
inlet.
If the cabinet is dirty, wipe it with wet cloth
Do not flush it directly with water.
Wipe it with neutral detergent.
Do not put the machine at damp place like
the bathroom. Never wash it with water. Do
not put wet laundries on the control panel.
Do not wash water-proof laundries like
the raincoat, bike covers etc. to avoid
abnormal vibrations in spinning.
Please clean it with brush every two months.
Do not wipe it with thinner, petrol, alcohol etc.
er
inn
Petrol
Alcohol
h
T
1.After washing, close the water faucet. ( If needed, you can dismantle the water inlet hose).
2.Do not store water in the washing machine for a long period. Drain the water completely after each using.
3.Be sure to pull off the power plug before maintenance.
Do not let the machine share one receptacle with other
electric appliances. If the plugging into the receptacle
is loose, do not use the plug any more.
4.Hang up the power cord and drain hose.
5.Wipe off the water drops on the surface of the machine and inside the tub. Open the top lid for some time
(about 1 hour), then close the top lid.
2
Safety precautions
Before washing, please fold up the laundry as needed, then put the laundry into the inner tub, flat and neat.
These fabrics are not washable:
1.Fabrics that deform when soaked in water;
Do not put hand into the rotating tub. It is dangerous
even if the rotation speed is slow. Take special care of
the children. Keep children away from the washing
machine to avoid them climbing on.
Do not decompose, repair or alter the machine by
yourself.
2.Fabrics that shrink, discolor or go through other exterior changes when soaked in water;
3.Fabrics that lose original texture when soaked in water;
4.Fabrics that discolor when soaked in water;
5.Fabrics that have pilling or pressed pile when soaked in water;
6.Fabrics that is damageable when soaked in water.
Upon completion of washing, iron the laundry with a steam iron.
When shrinkage occurs
Hold the steam iron above
Stretch the laundry to its original
size and locate it with pins. Use
the laundry. Reshape the
the laundry and do not touch
Do not put any hot or heavy items (such as the
kettle with hot water) on the washing machine.
Do not wash laundries with volatile materials
(such as thinner, petrol etc.).
a steam iron to dry the laundry
completely. Do not touch the
laundry. (As illustrated in Fig 2)
laundry. (As illustrated
in Fig 1)
Pin
Figure 2
Figure 1
l
tro
e
P
Benzene
3 Push "SOAK" "WASH" "RINSE" "SPIN" button to select suitable procedure program
Even there's no water in the tub, a certain period is required before spin starting.
Separate the laundries that are not colorfast from other laundries in washing.
The soak procedure can work in cooperation with automatic programs like STANDARD, HEAVY, CHILD, MEMORY
GENTLE. There is intermittent pulsator stirring during soak.
After the machine starts operation, you can only set the program and procedure during washing and soaking,
During rinsing ,you can only set the spinning time, and can not make setting in other cases.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities,
or lack of experience and knowledge,
unless they have been given supervision
or instruction concerning use of the
appliance by a person responsible for
their safety.
Keep the machine away from direct sunlight and
heat source like the heater.
During SPEEDY, TUB DRY programs, push the WASH, RINSE,SPIN button the machine has no reaction.
4 Push the " WATER LEVEL "button, select suitable water level
For STANDARD program, the washing machine will execute fuzzy program automatically to detect the cloth.
After defection, it can set the water level automatically.To select other water level, first push the "START/PAUSE"
button, then push the "WATER LEVEL" button to set the water level.
Children should be supervised to ensure
that they do not play with the appliance.
5 Push the "DELAY" button to select suitable reserve wash program
After switching on the power, the reserve program is set to off mode automatically. If you need to
set the washing procedure to be finished at reserved time, please push the DELAY "+ - " button to
set the reserve wash program. Refer to reserve button in Page 13 for selection.
When the DELAY function is activated, the indicator light of the program you
have set will be off. The digitron will display remaining delay time(hour).
During reserve procedure, push the "DELAY"+ - " button to display the reserve mode.
To change the running program or cancel the reserve setting, you need to switch off the
power and make new selection.
Please keep the lint filter in good condition,
and install it to proper position during
To protect your laundries and washing machine,
please take out all of the coins, buttons, sand, hairpin
and other foreign materials before washing.
Install
washing. If the lint filter is lost or
damaged, please contact the customer
care agent of our company.
Dismantle
6 Push the "START/PAUSE" button
Close the top lid
As the top lid opened, the washer will automatically alarm and stop running, exclusively during draining and water filling.
Please check if the water faucet is open, and if the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
To change the direction of drain pipe, please contact the customer care agent of our company.
Finish washing
After finishing washing ,it'll alarm and switch off power automatically.
Please don t use the washer in the environment below 0 C; if the washer has been stored below 0 C,
please be sure to ensure the washer is placed under the room temperature for 2~4 hours and then use
otherwise the washing effects may be lowered or the washer may be damaged.
Installation and adjustment
Please install and adjust the machine according to the requirement of the manual.
It is very important to your security and correct operating the machine.
I DELAY "+ - " button
Push down the "+ - " to select the reserve time(2h-24h).
Push the "+ - " button can display the reserve state.
Install the inner cover component
J
"SOAK " button
1.Open the top lid of the washing machine.
Press the "SOAK "button to select soak procedure.
Press the "SOAK "button, the light flashes then press SET "+ - " to select the desired soak time
from the STANDARD, HEAVY,CHILD, MEMORY programs( 0,10, 20,30,40 minutes).
SOAK
2.Put the inner cover component on the outer tub cover, aiming the inner cover
shaft to the installation hole of the corresponding outer tub cover shaft groove.
3.Firstly insert the inner cover shaft of one side into the corresponding outer tub
cover shaft groove, then push the another inner cover shaft into the corresponding outer
tub cover shaft groove. Please install to designated position to guarantee there are no
dropping or abnormal sound in opening and closing of the inner cover, and the operation
shall be smooth. Do not dismount the inner cover component after washing.
For GENTLE program, press "SOAK"button ,then press SET "+ - " button can change the process,
can not change time.
The button is unavailable from the SPEEDY , WOOL and TUB DRY programs.
K Reserve, remain time digitron
It displays "--" during detecting.
Outer tub cover
It displays remained reserve time (hour).
Right hand
It displays abnormal symbol in abnormal situation.(See to Page16)
Outer tub cover shaft groove
Inner cover shaft
Left hand
Inner cover component
L
"RESERVE WATER " button
Figure 2
You can choose "RESERVE WATER" function to keep the after rinsing water.
Washing machine will keep the after rinsing water once finish rinsing in tub about 4 hours, and buzzer every 15
minutes.( For example, if you choose "SECOND RINSE", the machine only keep the after second rinsing water,
If you choose "FIRST RINSE" and "SECOND RINSE" together, the machine will keep the after first and second
rinsing water)
Figure 1
RESERVE
WATER
Press"START/PAUSE" button or open and close the top lid one time to collect the after rinsing water, then the
machine will go on for next program.
If you don't collect the after rinsing water within 4 hours, the machine will drain automaticly, then go on for
next program.
Install the bottom plate
After you open the package, please lean
the washing machine gently down on soft
items ( like the towel cloth, blanket, etc. ).
Install the bottom plate to the bottom of
the machine, then lift the machine up
gently. See to the figure:
M
SET "+ - " button
I
Back
Refer to the description of operation button
Steps of using the operation buttons and description of each step
1.Push "POWER" button to switch on the power
Front
Bottom plate
Soft items
It has the special power resume function. In the case of power failure or the power plug is loose
during running , the machine can save the running program, and resume the program after the
power supply is recovered. You do not need to set the program again.
Two claws at the bottom cover shall
be inserted in two bar-shaped holes
in the stand. Make sure the claws
are firmly in place.
Section I enlarging
2.Push "PROGRAM" button to select suitable full-auto program
After the power is switched on, "STANDARD" is automatically set. To select other full-auto programs, please push
the "PROGRAM" button till the corresponding indicator is on. Refer to the "PROGRAM" button on Page 11.
E.g. Set to "SPEEDY"program for small quantity of laundries with light soil.
Fasten the bottom plate to
base frame with one screw
When a standard cycle is selected, the fuzzy program is run. The water level and the washing time can be
selected according to be texture and volume of the laundry. The washing cycle is automatically controlled.
13
D "WASH" button
Adjust the Installation position
Press the "WASH" button to select wash procedure.
Press the "WASH "button, the light flashes then press SET "+ - " to select the desired wash time
WASH
The largest allowable slope of the shank base of the machine is 2 .The slanting or rough ground will result in
unstable running or stoppage of the machine. Please adjust it with following methods:
from the STANDARD, HEAVY, CHILD, MEMORY programs 0-25mins
.
Press SET "+ - " button can change the process ,can not change time from the GENTLE and
WOOL programs.
The button is unavailable from the SPEEDY and TUB DRY programs.
Confirm it's horizontal:
Hang the lead line to check if it is
horizontal.
E "SPIN"button
Press the "SPIN "button to select spin procedure.
SPIN
Press the "SPIN "button, the light flashes then press SET "+ - " to select the desired spin time
from the STANDARD ,HEAVY ,CHILD ,MEMORY programs 0-9mins
The button is unavailable from the SPEEDY and TUB DRY programs.
.
Adjust the adjustable foot:
1 .To twist the adjustable leg, please first lift up the
side of the foot slightly, loosen the adjustable nut,
Press "SPIN"button ,then press SET "+ - " button can change the process,can not change time
from the GENTLE and WOOL programs.
the adjustable nut
and twist the foot.
Fasten
Loosen
High
the adjustable foot
Low
2 . After adjustment, fasten the nut.
F "WATER LEVEL"button
The washing machine can detect the laundries automatically. After detection, it will set the water level to suitable value
among 4, 6, 8,10 and 12 automatically. During the STANDARD program,You can also set water level by yourself. After
the machine is started, it will not set water level automatically. You shall push the "START/PAUSE " button to make new setting.
Usage of the drain hose
If there's water inside the tub, the machine cannot detect the laundries and will display water level 6 .If wet laundries
are put in, it may display water level 12. You must set suitable water level by yourself.
The drainage shall be smooth with the drain hose.
1.The height of the drain hose shall be less than
10cm, or the drainage will not be smooth, and
cost such long time that the machine may stop
at mid way.
During operation of SOAK,WASH and RINSE programs, you can push down the WATER LEVEL button to add water.
When you release the button, or it reaches the overflow water level, the machine will stop adding water.
WATER
LEVEL
4.If extra drain hose is needed, please make
separate purchase. The inner diameter of the
extra hose shall not less than 30mm, and the
length shall not exceed 1.5m.
The water level decided may be different from actual value because of the different moisture level of the laundries.
If SPEEDY program is selected, it will display water level 3 . It will display water level 4 when it rinses.
When STANDARD ,MEMORY ,HEAVY ,CHILD and GENTLE programs the rinse water value
will be one level higher than the wash water value.(Except 12 water value and when the rinse water value is
selected by yourself).
2.Do not step on or press the drain hose.
Under the wool program, only the 6 to12 water level can be selected.
>
30mm
G "AIR DRY" button
<10cm
<1.5m
Push the "AIR DRY" button to select air dry procedure. The program is chosen(0.5h, 1.0h,2.0h).
It can dry the inner tub and the outer tub when 0.5h,1.0h are selected , which can avoid growing mildew
on the outer tub and the inner tub.
AIR DRY
3. If the drain hose is too long, cut it at mid point.
To make smooth drainage, cut the front end of
the hose slantingly.
2.0h can dry laundries ,the max drying capacity of the fibre laundries is 1.5 kg.
5.If the extra hose is too long, cut it either at A
or at B.
"AIR DRY"program can not be reserved.
H "RINSE" button
Press the "RINSE "button to select rinse procedure.
RINSE
Press the "RINSE "button, the light flashes then press SET "+ - " to select the desired rinse times
from the STANDARD ,HEAVY ,CHILD ,MEMORY programs (0.1.2.3).
For GENTLE ,WOOL programs, press "RINSE"button , then press SET "+ - " button can change
the process ,can not change time.
The button is unavailable from the SPEEDY and TUB DRY programs.
12
5
Use the operation buttons
Description of operation button
How to change the direction of the drain hose
POWER
ON/OFF
K
SET
DELAY
STANDARD
HEAVY
MEMORY
GENTLE
FIRST RINSE
1.Dismantle the rear cover of the washing machine.
3.Dismantle the drain outlet protecting cover at the other side,
(the way is the same as the drain bushing),then install the drain
bushing, as indicated in Figure 4.
SECOND RINSE
THIRD RINSE
CHILD
WOOL
2.Put down the drain hose .Take off the drain hose
frame as indicated in Figure 1.Take the drain hose into
the cabinet ,then nip the drain fixing clamp to make it
deviated from the clip,the other hand is used to put down
the drain bushing,as indicated in Figure 2,3.
START
PAUSE
SPEEDY
°
TUB DRY
RESERVE
WATER
4.Extend the drain hose from the other side. Fix the drain hose
with drain hose frame onto the cabinet, as indicated in Figure 5.
AIR DRY
WATER
LEVEL
PROGRAM
SOAK
WASH
RINSE
SPIN
Drain outlet
protecting cover
Indicator mode and meaning
Drain hose
Off
Flashing, indicating the running program
On, indicating the program about to run or the selection mode
Figure 4
Figure 5
Drain hose support
Cabinet
Drain bushing
Figure 2
Drain bushing
Figure 1
5.Install the drain outlet protecting cover to the other side,
as indicated in Figure 6
Inner
Push
Outer
Drain bushing
Child lock function
Take
down
Drain hose fixing
clamp
The function is intended for children safety and preventing the washing program from accidental changes by children.
Figure 6
Push and hold the WATER LEVEL button and SPIN button, then push down the POWER ON/ OFF button .The digitron
displays
Figure 3
Push
. You can continue setting desired washing procedures. After setting ,push down the START/PAUSE button.
"
"
Remarks: In order to make sure of the correct of installation, it is suggested to change the direction of the drain hose
with our company serviceman .
The child lock function is activated, all of the buttons are locked and cannot make selection .
Release the child lock function :push down WATER button and SPIN button at the same time for more 2 seconds .
After a beep sound ,the child lock function is released.
A "POWER" button
Push the "POWER" button to switch on the power.
POWER
Under power-on mode, push it to switch off the power.
ON/OFF
Push the "POWER" button to switch on the power. If the "START/PAUSE" button is not pushed, the machine will
switch off the power automatically after 5 minutes.
B "START/PAUSE" button
START
After the power is switched on, press it to start the machine.
During working, push it to pause.
During pause, push this button to restart and go on working.
PAUSE
C "PROGRAM" button
Program
Application
Program
Application
The commom wash ,the washing machine will set
to MEMORY program including "wash ,rinse ,spin ,
water level "automatically last time
STANDARD Standard saving washing for normal laundries
MEMORY
PROGRAM
HEAVY
CHILD
Washing the relatively big and thick laundries
Washing the cotton textiles
GENTLE
WOOL
Washing the children clothes ,the default
program contains soak function
Washing for the woollen laundries,
under 2.5kg
Quick washing for normal laundries,
under 1.5kg
Avoid growing mildew on the outer tub and the
inner tub
TUB DRY
SPEEDY
°
°
6
11
Install the water inlet hose
Confirm the water faucet
Put in the laundries
The capacity of washing of the machine refer to the largest weight of the
standard laundries under dry condition that can be washed in one
time. Laundries quantity in one washing cycle shall be lower than
the standard capacity.
Water faucet,suitable
Water faucet,not suitable
The thickness ,size , type of the cloth will influence the actual washing capacity.
It is suitable to put in reasonable amount of laundries and the laundries can be turned
round in washing for one time washing.
Outlet end surface
Do not select " 4" water level for laundries less than 1.0kg ,so as to avoid
splashing of water.
>10mm
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Usage of detergent
How to use the softner
Connection between the water inlet hose jointer and the water faucet
The usage and dose of the softener as per the specifications of softener.
Before washing put the softener into the hole directly as indicated in the
left figure The softener will put into the washer when the last rinsing.
Refer to the following list for the usage of the detergent:selection of the
water level,water quantity and dosage of detergent
Control panel seat
Liquid detergent inlet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
After the softener is put in, please don't place for a long time otherwise
softener may solidify and cause flowing not smooth.
Remark: Do not use softener if rinse times is not two.
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
Access for detergent and washing powder
How to use the washing powder
It is suggested to add washing powder into the box
directly under fuzzy program and reserve program.
water inlet hose jointer
Screw
Detergent box
Dissolve directly inside the washing machine: (not
applicable for fuzzy and reserve program)
Slider
1.Add some water(select " 1 " water level).
2.Add washing powder. Run for about 30s to fully dissolve
Sign plate
Screw knife
Bushing
Figure 3
Access for softener
Lock level
Then push the"START/PAUSE" button.
the power.
3.Put in laundries. Select suitable water level. Push the
water inlet hose
"START/PAUSE"button again.
Figure 2
Figure 1
Quick dissolving of washing powder:
1.Prepare warm water of 30 C and container.
2. Add washing powder while stirring to dissolve it completely.
3.Fasten the four screws evenly. See to Figure 4.
4.Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
How to use the whitener
Please add suitable washing powder as per the laundries
quantity, the set water level and water quantity.
If you select "Speedy" program, it is suggested to use
liquid detergent instead of washing powder to guarantee
the washing effect.
Add water to decided level. Dilute the whitener with container,
Remark: Before installation, the threading is 4mm above the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
and then pour it into the liquid whitener inlet slowly.
Laundries with color or pattern is not colorfast, thus not applicable.
It is not recommended to use rich-foam washing powder.
The whitener shall not touch laundries directly.
See to the manual of whitener for the usage and dosage.
For whitener in powder, dissolve it before use.
Washing powder with poor quality or long-time storage may
get caked. Please clean the detergent box duly in usage.
About 4mm before twisting
About less than 2mm after twisting
Screw nut
Figure 5
Figure 6
Figure 4
10
7
Preparation before washing
Connection between the water inlet hose and the washer
Preparation before washing
1.Connect the water inlet hose.
1.Do not take off the water absorption cushion. Please check if the
2.Confirm that the washing machine is earthed
reliably. Then insert the power plug into the
receptacle. Do not connect the earth terminal
to the gas pipe and tap water pipe.
3.Put down the drain hose.
nut of the water
cushion is dropped or damaged before each usage. If it happens
inlet hose
please contact our after-sale department immediately.
2.Put the nut of the water inlet hose on the valve jointer.
3.Fasten the nut. Swing it gently to confirm if it's suitable.
jointer of the
water inlet valve
water absorption
cushion.
The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
Connection between the jointer of the water inlet hose and the water inlet hose
1.Push down the slider. Insert the water inlet hose into the jointer.
4.Slanting or uneven ground may result in
unstable working or abnormal noise. Please
make the machine stand horizontally.
the jointer of the
water inlet hose
Locking level
Slider
2.Hang the lock lever to the jointer. Release the slider till a click
sound is heard.
Pay attention to followings before washing the laundries
Check the connection between the jointer of the water inlet hose
and the water faucet
Clear the pocket.
Take out the coins ,
sand, hairpins etc.
Confirm if there's
special requirement
for the laundries.
The quantity of the
laundries shall not
exceed the rated
value. The big
laundries like the
jeans shall be put
in loosely.
Fasten the buttons
and zippers.
When the pulsator is
running ,the buttons of
the laundries may cause
noise. For the sake of
discretion ,please put
the laundries with
buttons into other
1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection
between the jointer of the water inlet hose and the
water faucet, and the installation of the water inlet
hose are firm, so as to prevent dropping from
improper installation position.
laundries.
Dismantle the water inlet hose
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries with unfast color from other laundries.
c. Put those laundries difficult to absorb water into water with hand.
1.Close the water faucet.
2.Press the locking lever. Push down the slider. Then pull of the water inlet hose.
d. For those laundries with heavy soil, please first remove the dirt like mud or dust. For the parts with heavy soil,
please apply detergent in advance, which can make it easier to remove the soil.
e. For those laundries that may get lint ball and those with long fur, turn it over before putting in.
f. Do not put those laundries polluted by chemicals directly into the washing machine.
g. For those small laundries and those may get twisting or worn, and woollen/fur laundries, please put them into
mesh bag for washing.
Locking level
Slider
If the machine is used frequently, the jointer of the water inlet hose can be
kept on the faucet to prevent damaging the fixing screw.
8
9
|