Model HF-299
Domestic Refrigerator
Operation Instructions
Contents
1-2
3
Name of various components
Placing environment
4
Usage preparation
5-6
7
Begin to use
Function introduction
8-9
10-11
12-13
14
Freezer usage instruction
Defrosting, cleaning, and stopping use
Question solution, after-sales service
Placing environment
The refrigerator should be placed on even, solid ground. When it is necessary to make it level
by insert something to raise it, the insert chosen should be steady, hard, and incombustible. It is
absolutely prohibited to use package foam block of the appliance as the insert. If it is not level,
you can make it level by turning and adjusting the bottom foot of the refrigerator.
It should be located in a well-ventilated
place, and there should be at least 10cm of
free space surrounding the refrigerator
including its back.
Refrigerator should be kept far from heat
source and avoid direct sunshine.
10cm
10cm
10cm
Be sure not to put in such a cold environment
as to freeze water
Do not place it in area damp or susceptible
to be splashed with water.
4
Usage preparation
Remove all package parts
Including foam base and the adhesive tape fixing
accessories, they all must be removed to prevent
the appliance being placed uneven.
Check accompanying accessories and
document
Check the items inside the package box with the
packaging list, and inquire selling shop, if any
discrepancy.
Locate the refrigerator on proper
place
(See section "placing environment")
It is advisable to carry out cleaning
prior to usage
(See latter section "cleaning" for its detailed
description)
Idle standing
After the appliance has been adjusted level, and
cleaned, let it remain idle for at least 30 minutes
before switching it on so as to ensure its normal
running.
5
Usage preparation
Left/right door opening function
This product provides the function of left/right
door opening, so you can realize the function
of opening door from right side by the following
step according to actual necessity.
1. Dismantle three screws of lower door hinge
for later use.
2. Carefully move downward and take out the
door, and carefully put it aside.
3. Dismantle part①, install it on right
corresponding position, and tighten it.
4. Dismantle part③, and fix it in the left hole of
the lower hinge②.
5. Use tool such as wrench to dismantle upper
hinge axle④, and install it on right
corresponding position.
6. Take the door, and carefully install it over
the hinge axle④.
7. Install the three screws dismantle in step 1 to
the left lower door hinge②.
8. Dismantle the hole-cover of door handle for
later use.
9. Dismantle door screw cover and screw⑦, and
install door handle⑤ on the right corresponding
position, then tighten it. Install the hole cover
taken in step 8 on the right side.
10. After completing installation of the door,
repeat opening and closing door for several
times, to ensure no abnormal noise, and tight
installation of all screws and hinge axles.
6
Begin to use
1.Starting of the appliance
For the initial use of the freezer, it is required
to start it at least 3hours in advance of putting
food.
Switching on the appliance. When plugged in,
the appliance shall automatically be set to
position 3, and quick cooling to position 0, green
power light I shall be turned on, and at the same
time, red alarming light L shall be turned on
together with buzzing sound. Press the buzzer
can stop the buzzing sound. Green power light I
indicates whether the appliance is switched on
or not.
Ｉ
Ｌ
Freezer Compartment Start
When the temperature of the appliance has been
lowered to required limit, green alarming light
L shall be automatically be turned off.
2.Appliance working method
Suggestion
！
No matter how ambient temperature changes, it
can maintain optimum refrigeration effect
without any other adjustment so long as you have
selected the artificial intelligence, giving you much
convenience.
You can set the appliance by selecting one of the two modes according to
necessity.
(1) Artificial intelligence mode: if no other special demand, we recommend you to use the
artificial intelligence. By pressing the artificial intelligence key to turn its indicating light on,
then the appliance shall automatically work.
(2) Manual adjusting mode: you can adjust and set the freezer temperature position according
to food storage necessity (such as for quick freezing). (See the following "temperature setting
and adjustment" in the later section of "function introduction").
7
Function introduction
Introduction of main panel
J
K
L
M
I
Ｏ
E
G
TEMP
SF
℃
F
D
N
B
C
F
A
H
A. Power switch
B. Unlock button
G+H Quick freezing button (unlocked
mode)
C. Automatic mode
D. Buzzer cancel
G+H Cold storage temperature indicator
button (locked mode)
E. Cold storage temperature increase
F. Cold storage temperature decrease
G. Freezer storage temperature increase
H. Freezer storage temperature decrease
I Power indicator
J Lock indicator
K. Automatic mode indicator
L. Over-temp warning indicator
E+F Temperature setting (after unlocking) M. Temperature indicator
N. Quick freezing indicator
O. Error indicator
Power control
After switching on the appliance, green power light I on the above of power switch A shall be
turned on. In order to prevent misoperation, it is necessary to press key A for 3 seconds in
order to stop its power supply, then the indicating lights and display windows shall all be
turned off, it shall stop cooling. If pressing the power key A again, the appliance shall resume
working, and all indicating lights and windows shall all be turned on again.
Locking and release
After switching on, the appliance shall automatically enter a locking state, light J shall be
turned off; by pressing key B, the locking shall be released, and light J shall be turned on.
Artificial intelligence setting
Under the artificial intelligence state, the appliance shall automatically adjust temperature
control position according to the ambient temperature changes, without manual control. Press
key C, and light K shall be turned on to enter the artificial intelligence state. Then quick
freezing position is on 0 and it is impossible to set quick cooling. Also the temperature position
is impossible to be set. To stop the state, press key C continuously for 3 seconds. At this
moment, light K shall be turned off.
8
Function introduction
Quick cooling setting
The quick cooling function is designed to keep food nutrition value. It can make the food
become completely frozen within as short time as possible. By pressing keys G+H together
at the same time for 3 seconds, the previous quick cooling setting position indicating light
shall flash. At this time, for each pressing of (key G), it shall increase 1 position from its
previous position. And for each pressing of (key H), the position shall decrease by one
step(in the range of positions 0-2). When under the quick cooling state, after compressor has
cumulatively worked for some period of time, it shall automatically stop the quick cooling
state, t o resume quick cooling position 0.
Note: When quick cooling position is on 0, the position indicating
light shall flash 3 squares successively from left to right.
Temperature setting and adjustment
Pressing the keys E+F at the same time for 3 seconds, current temperature setting position
shall flash. Then each pressing of (key E), the position shall be increased one position on
the current position. And for each pressing of (key F), position shall be lowered one step(
in the range of positions 1 to 7).
Over temperature alarming function
When the actual temperature sensed by freezing senor is higher than -5°C(excluding -5°C),
the over-temperature alarming light shall be continuously on, together with the sound of
buzzing. Press the buzzer release key D to release the buzzing, but the red over-temperature
indicating L shall be still on. When the temperature of the freezer is lowered to -5°C or lower,
the red over-temperature indicating light L shall be automatically turned off.
Power-off memory
The instantaneous working state at power failure shall be locked, and after power is restored
it will work according to the setting before the power failure.
Average temperature and malfunction display
Average temperature can be displayed only when locking indicating light is turned on. Pressing
the keys E+F at the same time, it is possible to display the instantaneous temperature of the
freezer.
Malfunction display:
(1) When there is malfunction in the environment sensor, the appliance shall be impossible to
enter artificial intelligence state, and shall display "F2".
(2) When there is malfunction on the freezing sensor, compressor shall enter the fixed cycle
of working for 20 minutes, then stop for 20 minutes and so on", but quick cooling function is
still effective, but over-temperature alarming shall be out of order, with display of "F1".
9
Freezer usage instruction
Use freezer for those foods to be stored
for long time.
The temperature of freezer compartment can be
-18°C, or lower, and under such a low
temperature it can basically inhibit the growth
or reproduction of bacteria. So it is advisable to
store in this room those foods to be kept for long
time, but careful with shelf life indicated on the
food package.
Quick-freezing
Ｇ
Before putting a larger amount of fresh food in
the freezer compartment, it is possible to use its
quick freezing function (see the description of
"quick freezing" in the above section of "function
introduction"). But it shall not be necessary to
set the quick-freezing function for the foodstuff
whose weight is less than 1kg or the food that
has already been frozen.
TEMP
SF
F
Ｈ
Making ice cubes
Pour about 3/4 of the volume of the icebox of
water to put in the freezer compartment for
freezing
When taking out the icebox, be sure not to
use knife or other metal tool for picking.
Generally, it can be taken down by slight force.
After taking out icebox, put it in warm water for
a while, and turn it with hand to take out ice
cubes.
Key to freezing food
It is advisable not to put excessive amount of
fresh food in freezer compartment, preferably, not
exceeding freezing capacity of the appliance.
Hot food should be cooled to room temperature
before putting in the freezer compartment.
Food should be divided into small appropriate
portions, so as to make it easier to be frozen
completely, and also to better guarantee quality
at melting and cooking. It is advisable for each
portion not to exceed 2.5kg.
10
Freezer usage instruction
It shall be better to package the food prior to
freezing it, and the package surface should be dry
to avoid being frozen together. The package material
should be smell-free, airtight, watertight, non-toxic,
and pollution -free, to prevent food flavor
contamination or quality deterioration. It is
advisable to mark the freezing date, storage
permissible period and food name on package bags
according to different food's shelf life so as to avoid
exceeding the storage limit.
In principle, take out exact required amount of
food from freezer compartment for melting. Melted
frozen food can not be re-frozen again, unless it
has been processed into cooked food, otherwise its
eating quality shall be influenced.
Take care not to put bottled beer, or beverage in
the appliance to prevent frost crack.
Method for taking out drawer
Pull forward it as shown in the drawing, and then
slightly raise it to take it out.
11
Defrosting, cleaning, stopping use
Defrosting
The freezer compartment is required to be
manually defrosted. After some time of using the
appliance, a layer of frost shall be formed on the
evaporator plate of the freezer compartment, and
it will consume more power if the layer gets too
thick. So when it has thick frost, it is required to
carry out defrosting with plastic scraper.
When carrying out defrosting, first pull out
its power plug to switch it off, wrap up the
foodstuff in cotton blanket and place them in cool
place. Then take out drawers.
①
②
As shown in the drawing, pull out the freezer
outlet tube ① of the discharge assembly. Place a
container ② at the outlet (or align the ① with
the back opening of lower freezer drawer) so as
to collect defrosted water. In order to speed the
defrosting process, it is possible to place a bowl
of hot water on the evaporator plate.
Note: it is strictly prohibited to carry
out defrosting with metal tool or
electric heater, to prevent damaging
appliance.
Treatment at power failure
When there is no power supply, the refrigerator
can still keep food without question for several
hours, even in summer.
At power failure, do not put any more new
fresh food.
Do the best not to open appliance doors.
If power stop is known in advance, it is
advisable to make many ice, put ice cube on the
top of freezer compartment.
Please note: Temperature rising in the freezer
compartment caused by power interruption or
other malfunction can shorten food storage
period, and deteriorate food quality.
12
Defrosting, cleaning, stopping use
Cleaning
The food remained in the refrigerator can
produce unpleasant smell, so it is required to
carry out periodical cleaning.
For safety, pull out power plug prior to
cleaning.
Clean the appliance by using soft towel or by
sponge dipping in warm water. (It is permissible
to add mild detergent). Be sure not to use scrub-
brush, steel brush, or organic solution such as
household cleanser, gasoline, banana oil,
acetone, benzole, or hot water, acid or alkali.
Use a dry cloth to wipe the water on the surface
of refrigerator
(1) Even for cleaning, do not spray water in order
to avoid affecting electric insulation feature.
(2) When cleaning such electric components as
"switch", "lamp" and "thermostat", use drier rag
or sponge
Door gasket is easy to get dirty, be sure to
frequently keep it clean.
Frequently remove the dust on the side plates,
to improve heat-expelling efficiency.
Stop usage
If the appliance is not to be in use for a longer
time, it is advisable to pull out power plug,
disconnect it with power supply, and carry out
cleaning for the appliance as described in the
above method.
When the refrigerator is not in usage for long
time, be sure to leave its door open, to prevent
food producing unpleasant smell.
Note: generally, do not stop using
refrigerator to avoid affect its usage
life.
13
Question solution, after-sales service
The following should not be regarded as defects.
When the appliance is first used, it can have longer working time and higher temperature inside
the appliance, and also compressor can have high temperature. All these are normal.
When air humidity is high, the appliance outside may have water drops, just wipe them with
soft cloth.
In humid season, when door is opened too frequently, or be kept open for too long time, humidity
is likely to be present in the appliance.
Refrigerant flowing in the refrigerator gives out some sound. When refrigerator starts or stops,
compressor clicks.
It is normal for the front of the appliance side panel to give heat.
When putting food or at higher ambient temperature, the appliance shall automatically increase
starting time.
Note: after switching it off, wait for at least 5 minutes before
switching it on again.
Before calling for repair, make certain the following items:
Question
Possible cause
Whether power supply is connected (plug, socket, fuse, etc)
Whether power voltage is too low?
Appliance not working
Whether ground is even?
Whether some part of the appliance has been in contact with
external object, or with the building wall
Too much noise
It is normal to have long time running for the first time usage.
There is large amount of food to be cooled
At hot weather, the appliance door is opened too frequently.
Thermostat temperature setting is incorrect.
Whether its placing is subject to the direct sunshine, or too near
the heat source such as stove, heating
Compressor runs for
long time or temp-
erature inside cabinet
is not desirably low
Whether ventilation is bad, whether back condenser is too dirty
Food getting dry
Food is not covered well, without package or not sealed well.
Appliance door is kept slightly open, or food has kept door open
Door is opened too frequently or for long time.
It is normal for frost or ice to form on the food package.
There is frost or ice
flowers on frozen food
Smelly food has not been packaged closely.
Check for spoiled food
It is necessary to carry out refrigerator interior cleaning. See
There is bad smell in
the appliance
section of "cleaning".
14
|