HP B-series 16Gb FC Switches
Quick Start Instructions
Overview
Read these instructions to set up and configure the HP
SN6000B 16Gb 48-port Fibre Channel Switch and
HP SN3000B 16Gb 24-port Fibre Channel Switch.
These instructions provide basic configuration steps.
For detailed rack mount and configuration instructions,
download the HP B-series 16Gb Switches Hardware
Reference Guide from the storage section of the HP
Figure 1 (page 1) shows the port side of the 48-port
switch.
SN6000B 16Gb 48-port FC switch
Figure 1 Port side of the 48-port FC Switch
1. System status LED
6. FC ports (44-47)
2. Management Ethernet port 7. FC ports (4-7)
with LEDs
3. USB port
8. Switch ID pull-out tab
4. FC ports (0-3)
5. FC ports (40-43)
9. Serial console port
10. System power LED
Verify the SN6000B 16Gb 48-port FC
switch carton contents
Verify that the carton contains the following (any SFPs
ordered will not be in this carton; they will be
packaged separately):
© Copyright 2012 Hewlett-Packard Development Company, L.P.
Printed in the U.S.
•
•
•
One HP SN6000B 16Gb 48-port FC Switch with
two integrated power supply/fan assemblies
Rubber feet, required to set up the switch as a
standalone unit
Serial cable with an RJ-45 connector plus an
adaptor for RJ-45 to DB9
HP Part Number: 5697-1520
Published: March 2012
Edition: 1
*5697-1520*
•
•
HP SAN Network Advisor DVD
Brocade EZ Switch and China ROHS
documentation
Page 1
To install and operate the switch successfully, ensure
that:
1. Place the switch on a flat surface and attach each
inner rail to the switch using three flat-head screws
•
•
•
The primary AC input is 85–264 VAC Nominal:
100–40 VAC, 2.0 A; 47–63 Hz. The switch
autosenses input voltage.
The rails are labeled Left and Right to designate
the left side and right side of the switch as viewed
from its nonport side.
The primary outlet is wired correctly, protected
by a circuit breaker, and grounded in accordance
with local electrical codes.
Figure 3 Attaching the inner rails to the switch
The supply circuit, line fusing, and wire size are
adequate, as specified by the electrical rating on
the switch nameplate.
For additional power supply information, see the HP
B-series 16Gb Switches Hardware Reference Guide.
Installing the SN6000B and SN3000B
16Gb FC Switches in a rack using the Rack
Mount Kit
You can use the SN6000B and SN3000B Switch Rack
Mount Kits to install your HP SN6000B and SN3000B
16Gb FC Switches in HP 10000 Series Racks.
2. Choose a rack mounting location that provides
clearance for the switch power cords to run
between the rack sides and the rails at the front
of the rack.
3. Attach each rear mounting bracket to a rear rack
upright column using two Phillips screws and
CAUTION: Install the Rack Mount Kit as
described in this section so that when the switch
is installed, the port side faces the rear of the
rack. This configuration optimizes performance
by:
Figure 4 Installing the rear mounting brackets
•
Providing better airflow by using a plenum
to force cool air to enter the switch from
the front of the rack
•
Providing room for a gradual bend in the
fiber optic cables because the port side of
the switch is set back from the edge of the
rack
Use only the screws provided in the Rack Mount
Kit. Using other screws can cause damage to
internal components.
To install the switch in a rack using the Rack Mount
Kit:
Page 3
4).
power supplies. Connect two power cords to the
48-port switch. Connect one power cord to the
The rails are labeled Left and Right to designate
the left side and right side of the rack as viewed
from the front of the cabinet.
IMPORTANT: Make sure that the power
cords do not come in contact with any
sharp edges.
Figure 5 Attaching the outer rails
NOTE: If you are configuring the second
(optional) power supply, the 24-port switch
will also have two power cords.
Figure 7 Connecting power and installing the
plenum
a. Slide the rail over the rear mounting bracket.
b. Attach the front of the rail to a front rack
upright column using two Phillips screws and
adapter washers.
c. Attach the outer rail to the rear mounting
brackets using a Phillips screw.
1. Cutouts for power cords 3. Power switches
TIP: Tighten the rear screws just
enough for the end of the screw to go
through the rear bracket. Later in the
procedure, you will need room to slide
the inner rail between the screw head
and the outer bracket.
2. Power cable plugs
4. Plenum thumb screws
8. Connect the other end of the power cords to
power sources on separate circuits to protect
against AC failure. (Make sure that two power
cords are connected to the 48-port switch and
one power cord is connected to the 24–poort
switch.)
5. From the front of the rack, slide the switch (with
inner rails attached) onto the outer rails, taking
care to align the inner rails with the attachment
screws on the outer rails at the rear of the rack.
NOTE: If you are configuring the second
(optional) power supply, the 24-port switch
will also have two power cords.
Figure 6 Installing the switch in the rack
9. Power on the power supplies by setting the power
switches to the ON position (|).
The power supply LEDs are amber until the Power
On Self Test (POST) is complete, and then change
to green. The HP SN6000B 16Gb FC Switch
takes several minutes to boot and complete POST.
NOTE: When installed, the plenum covers
the power supply switches and LEDs.
However, the LEDs are visible through the
air holes in the front of the plenum.
6. When the switch is in place, secure the inner rails
to the outer rails by tightening the screws at the
rear of the rack.
7. At the front of the rack, run the switch power cords
from the sides of the rack through the cutouts in
the rail, and then connect them to the switch
10. Slide the plenum over the nonport side of the inner
rails, taking care to bypass the power cables. See
11. Tighten the thumbscrews to secure the plenum to
the front of the rack.
Page 4
3. After POST is complete, verify that the switch
power and status LEDs on the port side of the
switch are green.
Install a standalone switch
1. Unpack the switch and verify the contents as
Switch setup
To set up the switch, you will need the following:
•
•
Standard screwdriver
If you are using static IP addressing, you will need
the following items (not required if you are using
Dynamic Host Configuration Protocol (DHCP)):
2. Apply the adhesive rubber feet to prevent the
switch from sliding off the supporting surface.
a. Clean the indentations at each corner on the
bottom of the switch to ensure that they are
free of dust or other debris.
b. With the adhesive side against the chassis,
place one rubber foot in each indentation
and press into place.
◦
◦
◦
Fixed IP address (IPv4 or IPv6) for the switch
Subnet mask value
Default gateway value
•
World Wide Name (WWN), located on the
switch ID pull-out tab
3. Place the switch on a flat, sturdy surface.
•
•
•
•
Ethernet connection (hub or switch)
Ethernet and Fibre Channel cables
Disk array with Fibre Channel ports
Browser that allows pop-up windows
Power on the switch
1. Connect a power cord to each power supply
present:
Connect the serial cable
•
For the 48-port switch, connect the power
cords to both power supplies and then to
power sources on separate circuits to protect
against AC failure.
1. Connect the serial cable to the serial port on the
switch and to an RS-232 serial port on the
workstation.
•
For the 24-port switch, connect a power cord
to either the single power supply present or
to both power supplies, if an optional second
power supply is present. Then connect the
power cords to power sources on separate
circuits to protect against AC failure.
If the serial port is RJ-45 instead of RS-232,
remove the adapter on the end of the serial cable
and insert the exposed RJ-45 connector into the
RJ-45 serial port on the workstation.
2. Disable any serial communication programs
running on the workstation.
Ensure that the cords have a minimum service
loop of 6 inches available and are routed to
avoid stress.
3. Open a terminal emulator (such as HyperTerminal
on a PC, or TERM, TIP, or Kermit in a UNIX
environment) and configure the application as
follows:
NOTE: If you are configuring the second
(optional) power supply, the 24-port switch
will also have two power cords.
For most Windows systems:
Bits per second: 9,600
Data bits: 8
2. Power on the power supplies by setting the AC
Parity: None
switches to the on position (|).
Stop bits: 1
Flow control: None
For most UNIX systems:
tip /dev/ttyb -9600
If ttybis already in use, try ttyainstead:
tip /dev/ttya -9600
The power supply LEDs are amber until POST is
complete, and then change to green. The switch
takes several minutes to boot and complete POST.
NOTE: Power is supplied to the switch as
soon as the first power supply is connected
and turned on.
Page 5
Remove the serial cable and replace the plug in
the serial port.
Log in to the serial console port
1. Verify that the switch has completed POST.
7. Connect the Ethernet port on the switch to the
When POST is complete, the port status, switch
power, and status LEDs return to a normal state.
Ethernet network that assigned the IP address.
2. When the terminal emulator stops reporting
information, press Enter to display the login
prompt.
Set the date and time
The date and time settings are used for logging, error
detection, and troubleshooting.
1. Using a Telnet or Secure Shell (SSH) session,
connect to the switch using the IP address that you
configured, and then log in to the switch as
adminusing the password you set when you
logged in to the serial console port.
3. Log in to the switch as admin, using the default
password, password.
You are prompted to change the default password
at initial login.
NOTE: You can configure the switch using a
static IP address or DHCP. With DHCP (enabled
by default), the switch obtains its IP address,
subnet mask, and default gateway address from
the DHCP server. The DHCP client can connect
only to a DHCP server that is on the same subnet
as the switch. The Ethernet cable must be
connected to the management Ethernet port on
the switch if you are using DHCP. If you are
using a static IP address, see “Set a static IP
2. Enter the datecommand using the following
syntax:
date "mmddHHMMyy", where:
mmis the month; valid values are 01 through 12.
ddis the date; valid values are 01 through 31.
HHis the hour; valid values are 00 through 23.
MMis minutes; valid values are 00 through 59.
yyis the year; valid values are 00 through 99.
NOTE: Values greater than 69 are
interpreted as 1970 through 1999; values
less than 70 are interpreted as 2000
through 2069.
Set a static IP address
1. Use the ipaddrsetcommand to set the Ethernet
IP address.
•
For an IPv4 address, use dotted-decimal
notation:
3. Enter the tstimezonecommand:
switch:admin> tstimezone
Ethernet IP Address:
192.168.74.102
[--interactive]/ [, timezone_fmt]
Use timezone_fmtto set the time zone by
country/city or by time-zone ID, such as PST. The
following example shows how to change the time
zone to US/Central:
•
For an IPv6 address, use colon-separated
notation:
switch:admin> ipaddrset -ipv6
--add 1080::8:800:200C:417A/64
switch:admin> tstimezone
nl
The following message confirms the change:
IP address is being changed...Done.
2. Provide the remaining network information:
Time Zone : US/Pacific
nl
switch:admin> tstimezone US/Central
nl
switch:admin> tstimezone
Ethernet IP Address: 192.168.74.102
nl
nl
Ethernet Subnetmask: 255.255.252.0
Gateway IP Address: 15.226.172.1
nl
Time Zone : US/Central
3. As an option, verify the IP address by entering
the ipaddrshow command at the prompt.
4. Record the IP address on the pull-out tab on the
port side of the switch.
5. When prompted, enter off to disable DHCP:
DHCP [OFF]: off
6. If the serial port is no longer required, use the
logoutcommand to log out of the serial console.
Page 6
4. Enter the tsclockservercommand to
1. Install the SFP+ transceivers in the Fibre Channel
ports on the switch to match the ports shown on
using an SFP+ transceiver that does not have a
pull tab, ensure that the wire bail is in the
unlocked position.
synchronize local time using NTP:
switch:admin> tsclockserver
“<ntp1;ntp2>”
The value of ntp1is the IP address or DNS name
of the first NTP server, which the switch must be
able to access. The value of ntp2is the second
NTP server and is optional. When multiple NTP
server addresses are specified, tsclockserver
sets the first obtainable address as the active NTP
server. The default value is LOCL.
Figure 8 Inserting an SFP+ transceiver with no pull
tab in a Fibre Channel port
switch:admin> tsclockserver
LOCL
switch:admin> tsclockserver "132.163.135.131"
switch:admin> tsclockserver
132.163.135.131
switch:admin>
Configure the zones, and perform device selection
See the Brocade Network Advisor User Manual,
available from the storage section of the HP website:
Figure 9 Inserting a 16 Gb/s SFP+ transceiver in
a Fibre Channel port
Connect devices
The Connect Devices window shows a graphical
representation of the switch with the device
connections, based on the information that you entered
NOTE: Only HP B-series optical transceivers
are supported. See http://hpsancompat.com/
for more information.
To connect devices:
Transceivers and cables are keyed so that they can
be inserted only one way. If a transceiver or cable
does not slide in easily, make sure it is oriented
correctly.
Do not insert a cable intended for an mSFP transceiver
into a regular SFP+ transceiver; you may damage the
cable. The mSFP transceivers and cables are supported
only with the 64-port 8Gb/s blade for the SN8000B
SAN directors. Do not force a standard SFP cable into
an mSFP transceiver; you may damage the transceiver.
a. Remove any protector plugs from the SFP+
transceiver. Insert each SFP+ transceiver
(right side up in the top row of ports, and
upside down in the bottom row of ports) until
it is firmly seated and the latching mechanism
clicks.
The 16 Gb/s SFP+ transceivers do not have
bails. Use the pull tab on the 16 Gb/s SFP+
transceiver to push the transceiver into the
port.
b. Close the latching bail on the non-16 Gb/s
SFP+ transceiver.
Page 7
2. Connect the Fibre Channel cables from the switch
to your host and storage devices. Ensure that the
physical connections match the connections on
the Device Connection screen.
a. Remove the plastic protector caps from the
Fibre Channel cable ends (if there are any),
and position the cable connector so that it is
oriented correctly.
b. Position a cable so that the key (the ridge on
one side of the cable connector) is aligned
with the slot in the transceiver (see
c. Insert the cable into the transceiver until the
latching mechanism clicks.
d. The Device Connection screen shows missing,
valid, and invalid connections as you cable
the switch. It can take up to 15 seconds for
the screen to display the connection as valid.
Verify that the connections display green and
then click Next.
Verify switch operation
1. Check the LEDs to verify that all components are
functional. For information about LED patterns,
see the HP B-series 16Gb Switches Hardware
Reference Guide.
2. Verify the correct operation of the switch by
issuing the switchShowcommand.
This command provides information about switch
and port status.
3. Verify the correct operation of the fabric by
issuing the fabricShowcommand.
This command provides general information about
the fabric.
4. Back up the switch configuration to an FTP server
by issuing the configUploadcommand and
following the prompts.
This command uploads the switch configuration
to the server, making it available for downloading
to a replacement switch if necessary.
Set switch features
This completes the initial setup of your HP SN6000B
or SN3000B 16Gb FC Switch. See the HP
StorageWorks Fabric OS 7.0.x Administrator's Guide
and the Fabric OS 7.0.x Command Reference Manual
for detailed instructions on setting all supported switch
features.
Page 8
|