MAF-001001
Table of Contents
...................................................................
REGULATORY INFORMATION
2
4
RECYCLING INFORMATION
.......................................................................
SAFETY NOTICE ........................................................................................... 5
PRECAUTIONS......................................................................................... 5
SPECIAL NOTES ON LCD MONITORS ................................................... 6
......................................................................................................
PREFACE
7
BEFORE YOU OPERATE THE MONITOR.................................................... 8
FEATURES................................................................................................ 8
CHECKING THE CONTENTS OF THE PACKAGE .................................. 8
POWER...................................................................................................... 9
CONTROLS AND CONNECTORS.......................................................... 10
ADJUSTING THE VIEWING ANGLE ...................................................... 11
OPERATING INSTRUCTIONS..................................................................... 12
GENERAL INSTRUCTIONS.................................................................... 12
FRONT PANEL CONTROL ..................................................................... 13
HOW TO ADJUST A SETTING ............................................................... 14
PLUG AND PLAY .................................................................................... 18
TECHNICAL SUPPORT (FAQ).................................................................... 19
Q & A FOR GENERAL DEFECTS .......................................................... 19
ERROR MESSAGE & POSSIBLE SOLUTION....................................... 20
APPENDIX ................................................................................................... 21
SPECIFICATIONS ................................................................................... 21
CONNECTOR PIN ASSIGNMENT .......................................................... 22
1
REGULATORY INFORMATION
Before operating the monitor, please read this manual thoroughly. This manual should be
retained for future reference.
FCC Class B Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy, and if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
The device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference; and (2) this device
must accept any interference received, including interference that may cause undesired
operations.
CANADA
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulation.
This device complies with requirement of EMC directive 89/336/EEC with regard to
Electromagnetic Compatibility, and 73/23/EEC and 93/68/EEC with regard to Low Voltage
directive.
Socket-outlet shall be near the equipment and shall be accessible.
2
TCO'03 ( TCO'03 applied model only )
Congratulations!
The display you have just purchased carries the TCO’03
Displays label. This means that your display is designed,
manufactured and tested according to some of the strictest
quality and environmental requirements in the world. This makes
for a high performance product, designed with the user in focus
that also minimizes the impact on our natural environment.
Some of the features of the TCO’03 Display requirements:
Ergonomics
Good visual ergonomics and image quality in order to improve the working environment
for the user and to reduce sight and strain problems. Important parameters are
luminance, contrast, resolution, reflectance, colour rendition and image stability.
Energy
Energy-saving mode after a certain time – beneficial both for the user and the
environment
Electrical safety
Emissions
Electromagnetic fields
Noise emissions
Ecology
The product must be prepared for recycling and the manufacturer must have a certified
environmental management system such as EMAS or ISO 14 001
Restrictions on
chlorinated and brominated flame retardants and polymers
heavy metals such as cadmium, mercury and lead.
The requirements included in this label have been developed by TCO Development in
cooperation with scientists, experts, users as well as manufacturers all over the world.
Since the end of the 1980s TCO has been involved in influencing the development of IT
equipment in a more user-friendly direction. Our labelling system started with displays in
1992 and is now requested by users and IT-manufacturers all over the world.
For more information, please visit
3
RECYCLING INFORMATION
HANNspree Inc. cares about environmental protection strategies and in using manufacturing
methods and treatments that lend themselves to conservation and recycling devices at the
end-of-life.
Our products, whenever possible, contain recyclable materials which can be recycled into new
devices. When necessary for operation, other materials may be classified as hazardous or
poisonous substances. We strongly encourage you to research the provided information
about recycling this device.
United State : http://newyork.earth911.org/
Europe :
Ireland
Company : McGrath Environmental Consultants Ltd.
Contact Person : Ms. McGrath Clodagh
Address: 20 Lower John Street, Cork, Ireland.
Tel : 021 4554833
Fax : 021 4505805
Norway :
Company : Bergfald & Co as
Contact Person : Mr. Solevåg Øystein
Address : Solavågsvegen 90, EIDSNES, NORWAY ,Post Code : N-6037
Tel : +47 40 23 47 05 Fax : +47 70 19 40 17
United Kingdom :
Company : ARENA Network Contact Person : Dr. Tillotson Allen
Address : Bank Buildings Treforest Estate, Pontypridd, Rhondda Cynon Taff, Kindom Post
Code :
CF37 5UR
Tel : 01443 844001 Fax : 01443 844002
4
SAFETY NOTICE
1. Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply
with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modification to this equipment. It is the responsibilities of the user to
correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously
high voltages are present inside the monitor. Do not open the cabinet. For all service
issues, please refer to qualified personnel only.
PRECAUTIONS
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry
tub, swimming pool or in a wet basement.
Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can
injure a person and cause serious damage to the appliance. Use only a cart or stand
recommended by the manufacturer or sold with the monitor. If you mount the monitor on
a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
instructions.
Slots and openings in the back and bottom of the cabinet are provided for ventilation. To
ensure reliable operation of the monitor and to protect it from overheating, be sure these
openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or
similar surface. Do not place the monitor near or over a radiator or heat register. Do not
place the monitor in a bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated on the
label. If you are not sure of the type of power supplied to your home, consult your dealer
or local power company.
Unplug the unit during a lightening storm or when it will not be used for long period of
time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire
and / or electric shock.
Never push any object into the slot on the monitor cabinet. It could short circuit parts
causing a fire or electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor by yourself; opening or removing covers can
expose you to dangerous voltages and other hazards. Please refer all service
issues to qualified service personnel.
To ensure satisfactory operation, use the monitor only with UL listed computers which
have appropriate configured receptacles marked between 100 - 240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
5
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn
off the Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop pattern
you use.
The LCD screen has effective pixels of 99.99% or more. It may include blemishes of
0.01% or less such as a missing pixel or a pixel lit all of the time.
Due to the nature of LCD screens, an after image of the previous displayed content may
remain if this image has been the displayed for several hours. The LCD screen should
recover if the image is changed or powered off for several hours.
If the screen suddenly flashes erratically or the backlighting fails, please contact your
dealer or service center for repair. Do not attempt to repair the monitor yourself.
6
PREFACE
Thank you for purchasing a Hannspree Liquid Crystal Display Monitor (LCD Monitor).
Please carefully read this manual in its entirety before setting up, using or operating
your Monitor. To ensure the safe and correct installation and operations of the Monitor,
it is important that the safety and operation instructions in this manual are followed.
This instruction manual is designed to assist you in setting up and using the Monitor.
The information in this manual has been carefully checked for accuracy; however, no
guarantee is given to the correctness of the contents. The information in this manual is
subject to change without notice.
To the extent allowed by applicable law, Hannspree, Inc. (“Hannspree”) shall not be
liable for direct, indirect, special, exemplary, incidental or consequential damages
arising from any defect or omission in this manual, even if advised of the possibility
of such damages in advance.
7
BEFORE YOU OPERATE THE MONITOR
FEATURES
19” screen TFT Color LCD Monitor
Crisp, Clear Display
Recommended Resolutions:
19" Wide (16:10)1440 X 900
19"(5:4)1280 X 1024
EPA ENERGY STAR®
Ergonomic Design
Space Saving, Compact Case Design
CHECKING THE CONTENTS OF THE PACKAGE
The product package should include the following items:
LCD Monitor
Screen
Base
Note : The screen and base design may vary on different models. For more information, please
refer to the Quick Start Guide of your Monitor model.
Cables and User manual
Power Cord
VGA Cable
Audio Cable
User’s manual
Warranty and Service Manual
DVI-D Cable (Optional)
Note : Images are for illustration only and may vary by model or region.
8
POWER
POWER SOURCE:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an Internal universal power supply that allows operation in either
100/120V AC or 220/240V AC voltage area (No user adjustment is required.)
3. Plug one end of the AC-power cord into the LCD monitor's AC input socket and the other
into a surge protection power strip or device.
9
CONTROLS AND CONNECTORS
CABLE CONNECTIONS:
Turn off your computer before performing the procedure below.
1. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the
other end to the computer’s D-Sub port.
-or-
2. Connect one end of a 24-pin DVI-D to the back of the monitor. Connect the other end to
the computer's DVI-D port.
note: This monitor is capable of operating in 'Dual input' mode. Only one of either the
15-pin D-sub or the 24-pin DVI-D connections is needed for normal operation.
3. Connect the audio cable between the monitor's audio input and the PC's audio output
(green port). This connection is optional and not required for normal operation of the
monitor.
4. Plug one end of the AC-power cord into the LCD monitor's AC input socket and the other
into a surge protection power strip or device.
5. Turn on your monitor and computer.
4
2
3 1
Figure.2. Connecting Cables
1.
3.
D-Sub Input
Audio Input
2.
4.
DVI-D Input
Power AC Input
10
ADJUSTING THE VIEWING ANGLE
For optimal viewing it is recommended to look at the full face of the monitor, then adjust
the monitor’s angle to your own preference.
Hold the stand so you do not topple the monitor when you change the monitor’s angle.
You are able to adjust the monitor’s angle at 20 alternative from -5 to 15 or 0 to 20 .
For more information, please refer to the Quick Start Guide of your Monitor model.
monitor’s angle
Figure.3.
NOTES:
Avoid touching the LCD screen when changing the viewing angle as it may cause
damage.
Be careful not to place fingers or hands near the hinges when tilting the monitor,
otherwise pinching can result.
11
OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are located at
front panel of the monitor (See Figure 4). By changing these settings, the picture can be
adjusted to your personal preferences.
The power cord should be connected.
Connect the Signal cable from the monitor to the computer.
Press the power button to turn on the monitor. The LED will turn green.
5
4
2
1
3
6
Figure.4. External Control Button
EXTERNAL CONTROLS:
1.
3.
5.
MENU
POWER
AUTO
2.
4.
6.
VOL +
VOL -
Power Indicator (LED)
12
FRONT PANEL CONTROL
Power Button:
Press this button to switch the monitor on and off.
Power Indicator (LED):
Green — Power On mode.
Orange — Power saving mode
MENU / ENTER:
1. Activate the OSD menu or adjust the function settings and confirmation.
2. Exit OSD menu when in volume OSD status.
VOL - / VOL +
:
1. Activates the volume control when the OSD is OFF.
2. Navigate through adjustment icons when OSD is ON or adjust a function when
function is activated.
Auto Adjust button:
When OSD menu is in off status, press this button to activate the Auto Adjustment
function.
(The Auto Adjustment function is used to optimized the H-Position, V-Position, Clock and
Phase.)
NOTES:
Do not install the monitor in a location near heat sources such as radiators or air dusts,
or in a place subject to direct sunlight, or excessive dust or mechanical vibration or
shock.
Save the original carton and packing materials, as they will come in handy if you ever
have to ship your monitor.
To ensure problem-free shipping, pack your monitor in the same packing materials
and carton as it was shipped from the factory.
To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains
may be removed with a cloth lightly dampened with a mild detergent solution. Never use
strong solvents such as paint thinners, benzene, or abrasive cleaning products. These
and other harsh cleaning agents will damage the cabinet of the monitor.
13
HOW TO ADJUST A SETTING
OSD Diagram
OSD Description
Brightness adjustment:
Select the ψBrightnessωoption on the
ψ Main Menu ω . Press enter and
adjust the level.
Contrast adjustment:
Select the ψContrastωoption on theψMain
Menuω. Press enter and adjust the level.
How to adjust screen position and
quality:
Select ψImage Settingωon the ψMain
Menuω, and then Press enter.
Horizontal position adjustment:
Select the ψH-positionωoption to shift the
screen image to the left or right. Press enter
and adjust the level.
Vertical position adjustment:
Select the ψV-positionωoption to shift the
screen image up or down. Press enter and
adjust the level.
14
OSD Diagram
OSD Description
Clock adjustment:
Select the ψClock Adjustmentωoption to
reduce the vertical flicker of characters on
the screen. Press enter and adjust the
level.
Phase adjustment:
Select the ψPhase Adjustmentωoption to
reduce the horizontal flicker of characters
on the screen. Press enter and adjust the
level.
How to adjust color:
Select the ψColor Settingωoption on the
ψMain Menuω, and then Press enter.
Move the cursor to one of the preset
options and select it.
User defined option:
Move the cursor to the User option and
select it
1. To adjust the red, enter the ψRωoption
and adjust the level.
2. To adjust the green, enter the ψGω
option and adjust the level.
3. To adjust the blue, enter theψBωoption
and adjust the level.
15
OSD Diagram
OSD Description
How to set the OSD:
Select ψOSD Settingωon the ψMain
Menuω, and then Press enter.
OSD horizontal adjustment:
Select the ψOSD H-Positionωoption to
adjust the horizontal position of the OSD.
Press enter and adjust the level.
OSD vertical position adjustment:
Select the ψOSD V-Positionωoption to
adjust the vertical position of the OSD.
Press enter and adjust the level.
OSD timer setting:
Select the ψOSD Time-outωoption to set
the OSD time out from 10 to 120 seconds.
Press enter and adjust the level.
OSD Transparency setting:
Select the ψOSD Transparencyωoption to
adjust the transparency of the OSD. Press
enter and adjust the level.
16
OSD Diagram
OSD Description
OSD color setting:
Select the ψOSD Colorωsetting option to
adjust the color of the OSD. Press enter
and adjust the level.
Language:
Select the ψLanguageω option to change
the language of the OSD. Press enter and
select a language.
(Please note the diagram is for reference
only. The OSD Language options may vary
by model and region.)
Volume adjustment:
Select the ψVolumeωoption to change the
volume level. Press enter and adjust the
level.
Sharpness:
Select the ψSharpnessωoption to adjust the
sharpness of the display. Set the value from
0 to 6.
DOS mode:
Select the ψDOS modeωoption to set the
monitor for use with PC. Press enter and
select 720 x 400 or 640 x 400.
17
OSD Diagram
OSD Description
Recall the factory settings:
Select theψFactory Presetωoption to reset
to the monitor’s default setting. This will
erase the current settings. Press enter and
select On or Off.
Input Setting:
Select theψInput Settingωoption to change
between the analog (D-Sub) or Digital
(DVI) source. Press enter and select Analog
or Digital.
PLUG AND PLAY ( Plug & Play DDC2B Feature )
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC
STANDARD. It allows the monitor to inform the computer or host system of its identity and,
depending on the level of DDC used, communicate additional information about its display
capabilities. The DDC2B is a bidirectional data channel based on the I²C protocol. The
host can request EDID information over the DDC2B channel.
If your computer, video card, and operating system support DDC2B, your monitor should
automatically be set to it's optimal configuration. Some computer systems may not have
the capability to properly detect this information. In addition, some computer systems will
require manually configuring the video options. In most cases, software and/or driver
updates will correct this issue. Please contact your computer or video card manufacturer
for more details.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE
MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics Standards
Association (VESA) and/or the United States Environmental Protection Agency (EPA) and
The Swedish Confederation Employees (NUTEK). This feature is designed to conserve
electrical energy by reducing power consumption when there is no video-input signal
present. When there is no video input signal this monitor, following a time-out period, will
automatically switch to an OFF mode. This reduces the monitor's internal power supply
consumption. After the video input signal is restored, full power is restored and the display
is automatically redrawn. The appearance is similar to a "Screen Saver" feature except the
display is completely off. The display is restored by pressing a key on the keyboard, or
clicking the mouse.
18
TECHNICAL SUPPORT (FAQ)
Q & A FOR GENERAL DEFECTS
PROBLEM & QUESTION
POSSIBLE SOLUTION
Power LED is not on
*Check the power cord.
*Check if the PC system is Plug & Play compatible.
*Check if the Video Card is Plug & Play compatible.
No Plug & Play or screen
image is stretch or seems
out of proportion
*Check if the D-15 plug pin of Video Cable is bent or
broken.
*Adjust the Clock, Phase or Contrast and Brightness
Controls.
*Manually set resolution to 1440 X 900
(for 19" Wide models) or 1280 X1024 for 19" models.
Please consult your operating system manual for specific
instructions.
Picture is dim, too bright or
fuzzy
*Update Video Card driver
Picture bounces or a wave
pattern is present in the
picture
*Reposition electrical devices that may cause electrical
interference.
*Computer Power Switch should be in the ON position.
*Computer Video Card should be snugly seated in its slot.
*Make sure monitor’s video cable is properly connected
to the computer.
*Inspect monitor’s video cable and make sure none of
the pins are bent.
*Make sure computer is operational by hitting the CAPS
LOCK key on the keyboard while observing the CAPS
LOCK LED. The LED should either turn ON or OFF after
hitting the CAPS LOCK key.
The power LED is ON
(orange) but there’s no
video or no picture.
Missing one of the primary
colors (RED, GREEN, or
BLUE)
*Inspect the monitor’s video cable and make sure that
none of the pins are bent.
Screen image is not centered *Adjust pixel frequency CLOCK and PHASE or press
or sized properly.
hot-key (AUTO).
Picture has color defects
(white does not look white)
*Adjust RGB color or select color temperature.
Horizontal or vertical
*Use win 95/98/2000/NT/ME/XP; "shut-down mode.
disturbances on the screen
Adjust CLOCK" and PHASE or perform hot- key (AUTO).
19
ERROR MESSAGE & POSSIBLE SOLUTION
CABLE NOT CONNECTED :
1. Check whether the signal-cable is properly connected. If the connector is loose,
tighten the connector screws.
2. Check the signal-cable’s connection pins for damage.
INPUT NOT SUPPORT :
Your computer has been set to an unsuitable display mode. Set the computer to
a display mode from the table below:
FACTORY PRESET TIMING TABLE:
HORIZONTAL
FREQUENCY (kHz) FREQUENCY (Hz)
VERTICAL
TIMING
MODE
640x350
640x400
640x400
640x480
640x480
640x480
640x480
720x400
832x624
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1024x768
1024x768
1152x864
1280x960
1280x1024
1280x1024
1440x900
1440x900
VGA-350
VGA-GRAPH
NEC PC9821
VGA-480
APPLE MAC-480
VESA-480-72Hz
VESA-480-75Hz
VGA-400-TEXT
APPLE MAC-800
SVGA
VESA-600-60Hz
VESA-600-72Hz
VESA-600-75Hz
XGA
COMPAQ-XGA
VESA-768-70Hz
VESA-768-75Hz
APPLE MAC-768
75Hz
31.469
31.469
31.5
31.469
35.00
37.861
37.5
31.469
49.725
35.156
37.879
48.077
46.875
48.363
53.964
56.476
60.023
60.24
67.50
60.00
64
70.087
70.087
70.15
59.94
66.67
72.809
75
70.087
74.55
56.25
60.317
72.188
75
60.004
66.132
70.069
75.029
75.02
75.00
60.00
60
60Hz
VESA-1024-60Hz
VESA-1024-75Hz
VESA-1440-60Hz
VESA-1440-75Hz
80
55.935
70.635
75
59.887
75
*
*
The two timing modes are for 19" widescreen support only.
*
20
APPENDIX
SPECIFICATIONS
Display size
Pixel pitch
19"(16:10)
0.2835(H) x 0.2835(V)
R,G,B Analog Interface
Digital (Dual-Input Model) H/V TTL
31KHz – 80KHz
56 – 75Hz
19"(5:4)
0.294(H) x 0.294(V)
LCD Panel
Video
Input
H-Frequency
V-Frequency
Display Colors
Dot Clock
16.2M Colors
135MHz
Max. Resolution
Plug & Play
1440 x 900
VESA DDC2BTM
1280 x1024
ON Mode
İ36W
İ1W
EPA ENERGY STAR®
OFF Mode
Audio maximum power output
1.2W (Amplifier)
D-Sub 15pin
DVI-D 24pin (Dual-Input Model)
Input Connector
Hor. :408.24mm
Hor. :376.32mm
Ver. :301.056mm
Maximum Screen Size
Power Source
Ver. :255.15mm
100~240VAC, 50~60HZ
Operating Temp: 5° to 35°C
Storage Temp.: -20° to 60°C
Operating Humidity: 10%~85%, non-condensing
Environmental
Considerations
LM01: 465*193*482 mm
LM02: 485*212*402 mm
LM03: 449*293*416 mm
LM05: 449*180*409 mm
Max : 485*293*482 mm
Dimensions (W*D*H)
Weight (GW/NW)
Max. 8 kg / 6.5 kg
UL/CUL, BSMI, CCC, CE, CB, PSB, FCC, VCCI,
C-TICK NEMKO-GS*, TCO’03*
Regulatory Compliance
The above specification is subject to actual panel specification and is subject to change
without prior notice.
Applied models only.
*
Note :
Maximum Resolution is dependant on the support of your computer system and video card.
21
CONNECTOR PIN ASSIGNMENT
15 - Pin Color Display Signal Cable:
1
6
5
10
11
15
PIN NO.
DESCRIPTION
PIN NO.
9.
DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
Red
+5V
Green
10.
11.
12.
13.
14.
15.
Cable Detection
Ground
DDC-Serial Data
H-Sync
V-Sync
DDC-Serial Clock
Blue
Ground
Ground
R-Ground
G-Ground
B-Ground
24 - Pin Color Display Signal Cable: (Dual Input Mode)
PIN NO.
1.
DESCRIPTION
TMDS Data 2-
PIN NO.
13.
DESCRIPTION
No Connection
2.
3.
4.
5.
6.
7.
8.
9.
TMDS Data 2+
TMDS Data 2/4 Shield
No Connection
No Connection
DDC Clock
DDC Data
NC
TMDS Data 1-
TMDS Data 1+
TMDS Data 1/3 Shield
No Connection
14.
15.
16.
17.
18.
19.
20.
21.
+5V Power
Ground(for+5V)
Hot Plug Detect
TMDS Data 0-
TMDS Data 0+
TMDS Data 0/5 Shield
No Connection
No Connection
TMDS Clock Shield
TMDS Clock +
TMDS Clock -
10.
11.
12.
22.
23.
24.
22
|