MODEL H7724
60" WORKBENCH
INSTRUCTIONS
Inventory
use the parts breakdown and listing in figure 2
and on page 4 to arrange your workbench parts
and inventory your shipment.
if any nonproprietary parts are missing (e.g. a
bolt or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
figure 1. model h7724 Birch Workbench.
features
•
•
Lacquer-sealed birch wood surfaces.
Four 191⁄4"W x 14"d x 21⁄4"h ball-bearing slide
drawers.
•
•
•
two 191⁄4"W x 14"d x 41⁄4"h ball-bearing slide
drawers.
figure 2. Fastener kit inventory.
Note: Refer to Page 4 for kit item part numbers.
two 211⁄4"W x 143⁄4"d x 121⁄2"h storage cabi-
nets.
Birch-faced vise with removable top plate and
63⁄4" leadscrew travel, 121⁄2" wide x 23⁄4" thick.
Four chrome bench dogs.
assembly
•
•
use the steps and figures below and refer to the
labels on the workbench parts to properly assem-
ble your workbench.
overall dimensions: 661⁄2" wide x 20" in depth
x 34" tall.
•
shipping weight: 148 lbs.
Tools Needed
Qty
Safety & Limitations
phillips screwdriver #2 ...................................... 1
hex Wrench 4mm (included)............................. 1
hex Wrench 5mm (included)............................. 1
•
•
•
maximum workbench table load is 500 lbs.
do not stand or climb on the workbench.
do not apply an unbalanced load on the table
that could result in workbench tipping over.
Keep children away from the workbench.
do not use workbench outdoors or in wet or
damp locations.
To assemble your workbench:
•
•
1. place the table (A) face down on the left over
shipping cardboard to avoid scratching the
workbench top.
•
do not overload the dogs or vise.
Copyright © ApriL 2009 By grizzLy industriAL, inC. rEVisEd dECEmBEr, 2011 (st)
WaRNINg: NO pORTION Of THIS MaNUaL May BE REpRODUCED IN aNy SHapE
OR fORM WITHOUT THE WRITTEN appROvaL Of gRIzzLy INDUSTRIaL, INC.
(For modELs mAnuFACturEd sinCE 12/11) #Cr11708 printEd in ChinA
10. insert two (W2) barrel nuts into the front
cross brace "i", so the barrel nuts slots are
horizontal and facing toward the inside of the
workbench (figure 7).
16. turn the vise handle clockwise until the wood
block (figure 8) just touches the table.
Note: Do not fully tighten the vise handle;
leave it loose enough so the wood block can
be adjusted in the next step.
17. Adjust the top of the wood block flush with the
surface of the table using a straightedge, as
shown in figure 9.
table top &
Wood Block Flush
Wood Block
Vise plate
figure 7. Front cross brace installation.
11. using the 5mm hex wrench, secure the front
brace and legs together with two (W1) barrel
bolts and two (W3) washers (figure 7).
#5 x 1 7⁄16"
Wood screws
12. tighten all loose fasteners except the four
(X1) fasteners holding the legs to the table.
figure 9. installing vise.
13. tighten the (X1) fasteners at this time.
1
18. using an ⁄8" drill bit, drill 17⁄16" deep holes
14. With assistance, position the workbench onto
its feet.
through the vise plate mounting holes and
into the wood block.
15. insert the metal shafts and threaded rod of
the vise through the holes in the vise wood
block (J) and into the vise support block
under the bench top (see figure 8).
19. secure the vise plate to the wood block with
two #5 x 17⁄16" wood screws (figure 9).
20. place a cotter pin in the end of the threaded
rod, bending it tightly around the shaft to
keep it from threading out of the vise support
block.
threaded rod
Wood Block
metal shaft
J
Vise support Block
figure 8. Vise threaded into vise support block.
-3-
model h7724 (mfg. since 7/08)
21. should you choose to use the (z4) bench
24. Lubricate drawer slides with light grease peri-
odically for smooth operation.
5
dogs, drill twelve ⁄8" (16mm) holes at the
shown locations in figure 10 in the table
top.
Maintenance
to avoid damaging it, do not store the workbench
outside, or in an overly damp or extremely dry
location.
60"
20"
If you need help with your new item, call our Tech
Support at: (570) 546-9663.
71⁄2
25⁄8
"
"
5"
41⁄4
"
figure 10. optional bench dog drilling locations.
22. using a standard screwdriver, assemble the
right and left drawer sides to the drawer back.
then slide the drawer bottom into the drawer
side grooves (figure 11) until it is fully seated
in the back groove.
figure 11. drawer assembly.
23. install the drawer fronts (figure 12), the
(y1) knobs, and insert the drawers into their
respective drawer slides.
figure 12. Final assembly.
-4-
model h7724 (mfg. since 7/08)
parts
parts Breakdown and List
REf paRT
DESCRIpTION
REf paRT
DESCRIpTION
Lr
ph7724002-2
ph7724001
LArgE right pAnEL
CornEr BrACKEt Assy.
ph7724015
tABLE top
A
B
C
d
F
ss
ph7724016
ph7724018
ph7724017
ph7724019
ph7724020
ph7724021
ph7724022
ph7724014-3
ph7724014-4
ph7724014-1
ph7724014-2
ph7724030
right sidE LEg
BACK Cross BrACE
LEFt sidE LEg
fastener Kit Item part Numbers (See figure 2).
W1
CEntEr pAnEL
ph7724006
ph7724008
pW07
BArrEL BoLt 31⁄2
"
W2
W3
W4
X1
X2
X3
y1
y2
z1
mAin Bottom pAnEL
Front Cross BrACE
VisE AssEmBLy
BArrEL nut
g
FLAt WAshEr 5⁄16"
hEX WrEnCh 5mm
Wood sCrEW 2"
i
J
sF
pAW05m
ph7724012
pW06
smALL Front pAnEL
smALL BACK pAnEL
smALL LEFt pAnEL
smALL right pAnEL
drAWEr Bottom pAnEL
FLAt WAshEr 1⁄4
"
sB
sL
sr
Bp
LF
LB
LL
pAW04m
ph7724009
ps25
hEX WrEnCh 4mm
puLL KnoB
phLp hd sCr 8-32 X 5⁄5
"
ph7724002-3 LArgE Front pAnEL
ph7724002-4 LArgE BACK pAnEL
ph7724005
ph7724025
ph7724026
spECiAL CAp sCrEW 2"
CottEr pin
z3
z4
ph7724002-1
LArgE LEFt pAnEL
BEnCh dog
-5-
model h7724 (mfg. since 7/08)
|