Grizzly Drill G1083 User Manual

MODEL G1083, G1370,  
G1514, G1515  
MORTISING ATTACHMENT  
INSTRUCTIONS  
The mortising attachment enables you to cut square mortises in wood stock with a drill press and matched  
mortising chisel and bit. Material is removed by the mortising bit and the mortising chisel simultaneously squares the hole.  
The mortising attachment consists of a fence that mounts to the drill press table, two hook clamps that secure the work  
against the fence, an adjustable hold–down that keeps the work from raising when the chisel is raised and a chisel holder.  
The chisel holder has a split casting that clamps to the drill press quill. The chisel holder will accept a variety of mortising  
chisel sizes.  
Securing Mortising Attachment to Drill  
Press  
1. Swing the drill press table away, lower the quill and  
lock in place. Slide the chisel holder onto the quill and  
tighten the bolt on the chisel holder split casting.  
Mortising  
1. Mark your mortise on the workpiece. Without drilling  
any stock, check the chisel position against the lay-  
out line. Make adjustments as required.  
2. Remove the workpiece from under the mortising chis-  
el and adjust the spindle stop to the desired depth.  
Crank the spindle down to make sure everything is  
clear.  
2. Slide a desired mortising chisel into the end of the  
chisel holder and secure.  
3. Slide the matching mortising bit through the chisel  
3. Position the hook clamps against the side o the  
and into the drill chuck. The tip of the mortising bit  
1
workpiece.  
should be at least 16" below the edge of the chisel.  
NOTE: It may be necessary to cut or grind the end of  
the bit that fits into the chuck so there will be proper  
clearance below the edge of the chisel. Secure the bit  
in the drill chuck.  
4. Adjust he hold-down so it is just above the workpiece  
and secure into position with the lock knob.  
5. For best results, select a drill press speed of 650 to  
1000 RPM.  
4. Fasten the fence assembly to the table. Ensure that  
the fence is positioned so it is square to the side of  
the chisel and set at the desired distance from the  
back of the chisel.  
6. Cut mortises in sequence as shown above. The dis-  
tance between position 1 and 2, 2 and 4 and so on  
should be less than the width of the mortising chisel.  
Sharpening  
The mortising bit and chisel must be periodically re-sharp-  
ened. Sharpen mortising chisels with a round slipstone,  
working from the inside of the chisel to the edge. Do not  
sharpen the outside edge. Any burr on the outside edge  
of the chisel caused by sharpening the inside must be  
removed with a flat stone. Sharpen the mortising bit with  
a flat stone or triangular file.  
COPYRIGHT © 1999 BY GRIZZLY INDUSTRIAL, INC. REVISED OCTOBER, 2007 (TR)  
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE  
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.  
#BA0520 PRINTED IN TAIWAN  
 

Grizzly Outdoor Cart T10041 User Manual
Haier Washer Dryer HW60 1082 User Manual
Hamilton Beach Toaster 22408 User Manual
HANNspree Laptop SN12E2 User Manual
Harbor Freight Tools Laser Level 90725 User Manual
HP Hewlett Packard TV DVD Combo C5445 90904 User Manual
Husqvarna Pole Saw PS 50 User Manual
iHome MP3 Docking Station ihome portable rechargeable stereo speakers for your kindle fire User Manual
iHome Speaker IBT25BC User Manual
Impex Home Gym IGS 09 User Manual