Model H8098
31⁄2 Ton SUV
Garage Jack
Operation
Pump Handle (Figure 1): To raise the jack, rotate
the pump handle clockwise completely, then move
the pump handle up and down. To lower the jack,
slowly rotate the pump handle counterclockwise.
Failure to follow these instructions could
result in serious personal injury or death:
1. DO NOT overload this jack beyond its
rated capacity. Overloading can cause
the jack to collapse and drop the load.
2. ALWAYS support the vehicle withappro-
priately rated support stands before
working under it.
3. DO NOT attempt to move the vehicle
while the jack is in use.
4. Use only on hard level surfaces like
concrete or asphalt. Other surfaces are
potentially unstable.
Pump
5. Center the load on the jack to maintain
proper balance and stability.
Handle
6. DO NOT use jack if it begins leaking
fluid or if it sinks when placed under
load. These are indications that the jack
needs to be immediately serviced.
Specifications
Maximum Lifting Capacity ................... 7000 Lbs.
Lifting Range ..........................................4"–251⁄4
"
Weight ..................................................... 93 Lbs.
Figure 1. Jack controls.
If you need help with the Model H8098, call our
Technical Support line at: (570) 546-9663.
COPYRIGHT © DECEMBER, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR8829 PRINTED IN CHINA
H8098 Parts Breakdown and List
��
�
��
�
��
��
��
��
�
��
��
��
��
�
�
��
��
��
��
��
��
��
��
��
��
��
�
�
����
�
��
�
�����
��
��
��
�
��
��
��
��
��
��
��
��
������
��
������
REF PART #
DESCRIPTION
LIFTING ARM ASSEMBLY
RUBBER PAD
REF PART #
24 PB49M
DESCRIPTION
HEX BOLT M12-1.75 X 20
TORSION SPRING
1
PH8098001
PH8098002
PH8098003
PR06M
2
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
PH8098025
PR11M
3
SADDLE
EXT RETAINING RING 25MM
LINKAGE BOLT
4
EXT RETAINING RING 16MM
LONG CONNECTING ROD
RIGHT LINKAGE BOLT
LOCK WASHER 18MM
HEX BOLT M12-1.75 X 25
LOCK WASHER 12MM
FRAME
PH8098027
PH8098028
PH8098029
PH8098030
PH8098031
PH8098032
PH8098033
PW08M
5
PH8098005
PH8098006
PLW12M
CONNECTING ROD ASSEMBLY
COTTER PIN 4 X 50MM
EXTENSION SPRING
CONCAVE GEAR
6
7
8
PB25M
9
PLW05M
PUMP ASSEMBLY
GEAR AXIS
10
11
12
13
14
15
16
17
18
19
20
21
22
23
PH8098010
PH8098011
PH8098012
PH8098013
PLW04M
EXT RETAINTING RING 20MM
FRONT WHEEL WASHER
FRONT WHEEL
FLAT WASHER 16MM
FLAT GEAR
PH8098035
PLW06M
LOCK WASHER 10MM
HEX NUT M10-1.5
FLAT WASHER 8MM
COTTER PIN 2 X 12MM
HEX BOLT M16-2 X 35
LOWER HANDLE
LOCK WASHER 8MM
HEX NUT M8-1.25
PN02M
PN03M
PW01M
PLW10M
LOCK WASHER 16MM
HEX NUT M16-2
PH8098039
PH8098040
PH8098041
PH8098042
PH8098043
PH8098044
PH8098045
PN13M
PH8098018
PH8098019
PN09M
REAR WHEEL
PULL ROD
UPPER HANDLE
HEX NUT M12-1.75
LEFT LINKAGE BOLT
SMALL PISTON
HANDLE SLEEVE
MACHINE ID LABEL
FILL PLUG
PH8098021
PH8098022
PH8098023
HANDLE SOCKET
The machine ID label warns about hazards and ways to prevent injury. The owner of the jack
MUST maintain the original location and readability of the label. If the label is removed or becomes
�����������������������������������������������������������������������
�������������������������������������
������������������������������������
�����������������
��������������������������������
���������������������������������
����
�����������������
����
������������������
|