Failure to follow these warnings a
could result in seriou
Highchair
OWNER’S
MANUAL
Model No. _______
Serial No. ________
Dear Customer,
Please fill in the
model and serial
numbers above
from the label on
the back of the
footrest of your
new highchair.
Prevent serious injury or de
falls or sliding out. Always s
child in the restraint.
Model 3625
Congratulations on your purchase of a
Graco® highchair!
Graco is the recognized leader in the
design and manufacture of quality baby
products. We believe your new Graco®
highchair is a wise choice, promising
many hours of enjoyment for your baby.
Before using your highchair, please take a
few minutes to read this Owner’s Manual.
The short time you spend reading these
instructions will help you to use your
highchair properly.
NEVER LEAVE YOUR CHILD
UNATTENDED. Always keep
your child in view.
Please save your Owner’s Manual
for future use.
FOLLOW ASSEMBLY INSTRUCTIONS CAREFULLY.
If you experience any difficulties, please contact the
Customer Service Department.
Customer Satisfaction
Our goal is to make every product the best it
can be! We are also committed to supporting our
products after purchase. If you would like to speak
to Graco about your product, please contact our
Customer Service Department at 1-800-345-4109
Our knowledgeable staff will be ready to answer
any questions you may have concerning parts, use,
or maintenance. When you call, please have the
model and serial numbers ready so your call
may be processed quickly and efficiently.
THIS HIGHCHAIR IS DESIGNED TO BE USED by a child
between 6 months and 3 years of age. Maximum weight
37 pounds (16.8 kg).
DO NOT FORCE TRAY against child. Use only the five
adjustment positions. Be sure both adjustment fingers are
engaged in armrest slots.
DO NOT ADJUST the highchair with your child in it.
© 1999 Graco 226-10-99 IS3556
2
Step 5.
Assembling
the Highchair
Both “U”
curves up
Hold rear tube as shown.
Slide plastic brackets onto
upper tube.
Step 1.
Hold front tube with ends up.
Place a foot (smooth side up)
at one curved corner of tube.
Insert a screw through tube
and into foot, then tighten.
Repeat with other corner
Plastic bracket
Step 6.
Slide front tube onto upper
tube as far as it will go, until
the holes in the tubes line up.
and both feet of rear tube.
Collars
Step 2.
Lay seat face down on the
floor as shown. Insert
support tube through both
collars on bottom of seat.
Support tube
Step 3.
“U” curve
down
Mount a slider onto
each end of the
support tube. Slider
loops should be
facing UP, as shown.
Push end of slider
all the way into collar.
Step 7.
Pull rear tube up until holes
in plastic bracket line up with
holes in the tubes.
Step 4.
CHECK that holes in upper
tube, front tube AND plastic
brackets all line up with each
other.
Insert both ends of upper
tube into slider loops and
pull all the way through as
shown.
Insert a T-nut into one plastic bracket hole. It must pass
through both tubes, as shown enlarged below. Insert a
screw into other side of plastic bracket and screw it
into T-nut.
Still holding ends of tube,
locate pegs. Push pegs
through the channel until
they pass the snap. Slide
pegs into first notch of
height-adjustment track.
CHECK that tubes are securely connected by trying to pull
them apart.
Repeat for other plastic bracket.
Pegs
First notch of
height adjustment track
226-10-99 IS3556
5
6
If it becomes necessary to remove the seat belt,
follow these instructions:
Step 1.
First buckle the belt.
Then unthread end of
seat belt through the
buckle as shown.
Step 2.
Pull other end of the seat
belt through the belt retainer
as shown.
Set highchair upright.
It should look like this.
Step 3.
To rethread buckle, thread
the free end of the waist belt
back through the belt retainer.
The “GRACO” logo must be
on the front of the buckle.
Step 8.
Place seat pad in seat as
shown. Insert tabs of seat
pad into the corresponding
slots in the seat. From rear
of seat, hook all four tabs
over plastic anchors.
Step 4.
Thread belt through
the buckle as shown.
The left end of the buckle
must be smooth side up
to thread the belt in the
buckle properly. The
other side of the buckle
has teeth.
Smooth side
If you have difficulty getting
the belt into the buckle, check
to make sure that the smooth
side of the buckle is up.
To Use Seat Belt
Step 1.
CHECK that the belt is
threaded correctly by pulling
on the seat belt. The belt
should not slip through
the buckle.
Snap buckle together as
shown. Adjust belt as needed
to get a snug fit around
your child.
Step 2.
Press on prongs at top and
bottom of buckle to release.
Prevent serious injury or death from falls
or sliding out. Always secure your child in the restraint.
Do not depend on the tray alone to hold your child.
7
8
To Use Tray
To Fold Highchair
Place tray on armrests of
seat. Pull out side handles
under the tray. Put tray in
one of the five adjustment
positions, and release
side handles.
Lay highchair on the
floor as shown. Press in
metal buttons at base of both
plastic brackets. Push rear
base down to fold highchair.
CHECK that tray is securely
attached by pulling forward
on the tray.
Push on
front button
Use either the side handles
or the front button to adjust
the position of the tray.
DO NOT
force the tray against
your child. Keep your
child’s hands and fingers
away from the tray when
adjusting the tray.
Tray may be removed from
highchair by using the side
handles.
To Adjust Height
DO NOT
adjust the highchair with
your child in it.
Pull UP
Hold chair frame down
and lift seat firmly to
free pegs from height-
adjustment notch. Slide
seat up or down in the
track, then snap it into
desired height setting.
When adjusting
height, be careful to
keep fingers away from
height-adjustment track.
There are five possible
height settings. The highchair
can be used as a toddler chair
by adjusting to the lower
height settings.
CHECK that both sides of
chair are snapped into the
desired height-adjustment
notch.
226-10-99 IS3557
9
10
Replacement Parts
Instructions for ordering highchair parts:
Complete form below. Your highchair model number MUST
be included on the form to ensure proper replacement parts.
Your model number can be found on a sticker on the
back of the footrest. Payment must accompany your
order.
Parts List:
Price:*
Seat.................................... $22.00
Seat pad............................. $16.00
Tray.....................................$18.00
Upper tube..........................$ 9.50
Support tube....................... $ 7.00
Rear tube............................$10.00
Front tube........................... $ 9.50
Slider...................................$ 5.00
Foot.....................................$ 5.00
Hardware.............................$ 5.00
* Prices subject to change without notice.
IF YOU NEED HELP
If you have any questions or if you need any parts
not listed, please call toll-free:
1-800-345-4109
Return the form below with payment to:
GRACO CHILDREN’S PRODUCTS INC.
CUSTOMER SERVICE DEPARTMENT
P.O. BOX 100, MAIN STREET
ELVERSON, PA 19520
Model Number SHIPTO:
(Must be filled in)
Name
Seat
Seat pad
Tray
Address
Upper tube
Support tube
Rear tube
Front tube
Slider
City, State, Zip
(
)
Telephone
Foot
Hardware
Check enclosed
(payable to Graco Children’s
Products Inc.)
Charge to credit card:
Visa
MasterCard
Discover
Total:
Shipping
& handling:
$5.00 Account #:
6% sales tax
(PA only):
Expiration date:
Signature:
Total amount
due:
11
|