Graco Food Processor 334011B User Manual

Instructions-Parts  
334011B  
Merkur ES Hopper Kit  
EN  
Material supply for Merkur ES spray packages. This manual contains kit installation instructions  
only.  
Important Safety Instructions  
Read all warnings and instructions in this manual and in your Merkur  
ES Spray Package manual.  
Save all instructions.  
17A493, 2 Liter Hopper  
PROVEN QUALITY. LEADING TECHNOLOGY.  
 
Warnings  
WARNING  
EQUIPMENT MISUSE HAZARD  
• Misuse can cause death or serious injury.  
• Do not operate the unit when fatigued or under the influence of drugs or alcohol.  
Technical Data  
• Use fluids and solvents that are compatible with equipment wetted parts. See  
in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete  
information about your material, request MSDS from distributor or retailer.  
• Do not leave the work area while equipment is energized or under pressure. Turn off all  
Pressure Relief Procedure  
equipment and follow the  
when equipment is not in use.  
• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine  
manufacturer’s replacement parts only.  
• Do not alter or modify equipment.  
• Use equipment only for its intended purpose. Call your distributor for information.  
• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.  
• Do not kink or over bend hoses or use hoses to pull equipment.  
• Keep children and animals away from work area.  
• Comply with all applicable safety regulations.  
TOXIC FLUID OR FUMES  
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on the skin,  
inhaled, or swallowed.  
• Read MSDSs to know the specific hazards of the fluids you are using.  
• Store hazardous fluid in approved containers, and dispose of it according to applicable  
guidelines.  
PERSONAL PROTECTIVE EQUIPMENT  
Wear appropriate protective equipment when in the work area to help prevent serious injury,  
including eye injury, hearing loss, inhalation of toxic fumes, and burns. This equipment includes  
but is not limited to:  
• Protective eyewear, and hearing protection.  
• Respirators, protective clothing, and gloves as recommended by the fluid and solvent  
manufacturer.  
334011B  
3
 
Installation  
Installation  
Wall Packages  
1. Install bracket to the side of the existing air motor  
bracket. Secure using bolts (6), washers (9), and  
nuts (10).  
2. Slip bracket holes over bolt heads and slide into  
place.  
3. Tighten bolts.  
4. Grease adapter o-ring (11).  
5. Install pump hose fitting (2b) into the lower and  
tighten the jam nut (2c)  
6. Open clamp (4) around hopper outlet.  
7. Use 7/8” hex on outlet hose fitting (2a) to rotate  
the hose in the hopper (1) for optimal fit in the  
bracket (8).  
8. Tighten the adjustable screw on the clamp (4)  
and close latch.  
NOTE:  
The adjustable screw should be tight  
enough that the latch on the clamp has firm  
resistance when closing.  
Stand Packages  
1. Loosen the two stand bolts on either side of the  
existing air motor bracket.  
NOTE:  
Nuts (10), washers (9), and bolts (6) are  
used with wall packages only.  
2. Slip bracket holes over bolt heads and slide into  
place.  
3. Tighten bolts.  
4. Grease adapter o-ring (11).  
5. Install pump hose fitting (2b) into the lower and  
tighten the jam nut (2c).  
6. Open clamp (4) around hopper outlet.  
7. Use 7/8” hex on outlet hose fitting (2a) to rotate  
the hose in the hopper (1) for optimal fit in the  
bracket (8).  
8. Tighten the adjustable screw on the clamp (4)  
and close latch.  
NOTE:  
The adjustable screw should be tight  
enough that the latch on the clamp has firm  
resistance when closing.  
4
334011B  
 
 
Parts  
Parts  
Hopper Kit 17A493 Parts  
Ref  
No. Description  
Qty.  
1
1
HOPPER, 2L  
2
3
HOSE, Low Pressure Suction Hose  
COVER  
1
1
4
5*  
6
7  
8
CLAMP, Quick Release  
SCREEN, SST 30 Mesh  
SCREW, 1/4”-20x5/8”  
O-RING  
1
1
2
1
BRACKET  
2
9
WASHER  
2
10  
NUT  
2
11 O-RING  
1
12 LABEL, warning  
1
* These parts are included in kit 17B207 (pack of 5)  
These parts are included in repair kit 17B208  
Replacement Danger and Warning labels, tags,  
and cards are available at no cost. Order part  
number 17A366.  
Kit and Accessories  
Kit Description  
Part No.  
Kit Description  
Bungee Cord  
Clamp  
Part No.  
17C166  
17B831  
Screens (pack of 5)  
Suction Hose O-rings  
17B207  
17B208  
Technical Data  
U.S.  
160°F  
Metric  
71°C  
Maximum fluid temperature  
Ambient air temperature range  
Hopper assembly wetted parts  
35–120°F  
2–49°C  
Nylon, acetal, polyethylene  
334011B  
5
 
 
Graco Information  
To place an order,  
contact your Graco Distributor or call to identify the nearest distributor.  
or Toll Free: Fax:  
Phone:  
612-623-6921  
1-800-328-0211  
612-378-3505  
All written and visual data contained in this document reflects the latest product information available at the time of publication. Graco  
reserves the right to make changes at any time without notice.  
Original Instructions. This manual contains English, MM 3A0732  
Graco Headquarters:  
International Offices:  
Minneapolis  
Belgium, China, Japan, Korea  
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS, MN 55440-1441 • USA  
Copyright 2014, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.  
Revision B, August 2014  
 

Grandstream Networks Washer Dryer HT503 User Manual
Haier Refrigerator HXC 158 User Manual
Hamilton Beach Can Opener 840213800 User Manual
Harbor Freight Tools Power Hammer SDS MAX TYPE User Manual
Hario Glass Hot Beverage Maker V60 User Manual
HP Hewlett Packard Cell Phone 50091 1 002 User Manual
HP Hewlett Packard Server BL870c User Manual
Humax Satellite TV System FOXSAT HDR User Manual
Husqvarna Lawn Mower YTH220 TWIN User Manual
Ice O Matic Ice Maker ICE0400A3 T3 W3 User Manual