REN Number
Telephone Operation
Model 29253
On the bottom of this equipment is a label indicating, among other
information, the Ringer Equivalence Number (REN) for the equipment.
Redial
This unit redials up to 32 digits. To automatically redial the last number
you called:
Series Trimline
Phone User’s Guide
The REN is useful in determining the number of devices you may connect
to your telephone line and still have all of these devices ring when
your telephone number is called. In most (but not all) areas, the sum
of the RENs of all devices connected to one line should not exceed 5.
To be certain of the number of devices you may connect to your line
as determined by the REN, you should contact your local telephone
company.
1. Pick up the handset and wait for a dial tone.
2. Press the redial button.
Flash
Press the flash button instead of the hook switch to activate custom
calling services such as call waiting or call transfer. Custom calling
services are provided by the phone company.
REN Number is located on the cabinet bottom.
Receiver Volume
Licensing
You may control the listening level with the volume switch on the bottom
of the handset. It has 3 levels: lo, mid, and high.
Licensed under US Patent 6,427,009.
Hearing Aid Compatibility (HAC)
Ringer Volume
This telephone system meets FCC/Industry Canada standards for Hearing
Aid Compatibility.
You may control the ringer volume level with the switch located above the
touch tone pad on the handset.
= ringer tone will be loud
= ringer tone will be low
= telephone will not ring
CAUTION:
RISKOFELECTRICSHOCK
DONOTOPEN
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
THE LIGHTNING
CAUTION: TO REDUCE THE
FLASH AND ARROW RISK OF ELECTRIC SHOCK, DO
HEAD WITHIN THE NOT REMOVE COVER (OR
TRIANGLE IS A
WARNING:TO
WARNING SIGN
ALERTING YOU OF
IMPORTANT
BACK). NO USER
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSETHIS
Troubleshooting Tips
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
No dial tone.
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
• Press and release the hook switch. Check the hook switch: Does it fully
extend when the handset is lifted from the cradle?
PRODUCT TO RAIN
OR MOISTURE.
SEE MARKING ON BOTTOM
/
BACK OF PRODUCT
Phone doesn’t ring.
• Make sure RINGER switch (located on the handset) is set to loud or low.
Introduction
• Are you using too many phones on one line? (The total REN of all
phones on the same line should not be greater than the maximum
REN for your calling area. See Equipment Approval Information).
Other party cannot hear you.
• Make sure phone cord is securely plugged in.
• Make sure extension phones are on the hook at the same time you’re
using the phone. It is normal for the volume to drop when additional
extension phones are used at the same time.
Phone “howls” when handset is placed near the base and handset volume
level is too high.
Your telephone is designed to give you flexibility in use and high quality
performance. To get the most from your new telephone, we suggest that
you take a few minutes right now to read through this instruction manual.
CAUTION: When using telephone equipment, there
are basic safety instructions that should always
be followed. Refer to the IMPORTANT SAFETY
INSTRUCTIONS provided with this product and save
them for future reference.
Important Information
NOTE: This phone uses Touch-Tone dialing service only.
For this telephone to function properly, you must use
Touch-Tone service available through your local telephone
company.
NOTICE: This product meets the applicable Industry Canada technical
• This is normal feedback due to handset volume level being set
to maximum.
specifications.
Operation is subject to the following two conditions: (1) This device may
not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
General Product Care
Before You Begin
To keep your telephone working and looking good, follow these guidelines:
Wall plate
Telephone Jack Requirements
The equipment must be installed using an acceptable method of
connection. The customer should be aware that compliance with the
above conditions may not prevent degradation of service in some
situations.
• Avoid putting the phone near heating appliances and devices that
generate electrical noise (for example, motors or fluorescent lamps).
• DO NOT expose to direct sunlight or moisture.
• Avoid dropping and other rough treatment to the phone.
• Clean with a soft cloth.
• Never use a strong cleaning agent or abrasive powder because this
will damage the finish.
• Retain the original packaging in case you need to ship the phone at a
later date.
To use this phone, you need an RJ11C (CA11A) type
modular telephone jack, which might look like the
one pictured here, installed in your home. If you don’t
have a modular jack, call your local phone company
to find out how to get one installed.
Modular
telephone
line jack
Repairs to certified equipment should be made by an authorized Canadian
maintenance facility designated by the supplier. Any repairs or alterations
made by the user to this equipment, or equipment malfunctions, may give
the telecommunications company cause to request the user to disconnect
the equipment.
Important Installation Information
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Temporarily disconnect any equipment connected to the phone such
as faxes, other phones, or modems.
Users should ensure for their own protection that the electrical ground
connections of the power utility, telephone lines and internal metallic
water pipe systems, if present, are connected together. This precaution
may be particularly important in rural areas.
Service
Thomson Digital Technologies Ltd., warrants to the purchaser or
gift recipient that if any manufacturing defect becomes apparent
in this product within 1 year from the original date of purchase, it
will be replaced free of charge, including return transportation.
CAUTION: Users should not attempt to make such connections themselves,
but should contact the appropriate electric inspection authority, or
electrician, as appropriate.
This warranty does not include damage to the product resulting
from accidents, misuse or leaking batteries.
NOTES: This equipment may not be used on coin service provided by
the telephone company.
Handset Layout
Should your product not perform properly during the warranty
period, either:
Ringer
Interference Information
flash
volume
switch
(button)
1. Return it to the selling dealer with proof of purchase for replace-
ment,
This equipment generates and uses radio frequency energy which may
interfere with residential radio and television reception if not properly in-
stalled and used in accordance with instructions contained in this manual.
Reasonable protection against such interference is ensured, although
there is no guarantee this will not occur in a given installation. If interfer-
ence is suspected and verified by switching this equipment on and off, the
user is encouraged to try to correct the interference by one or more of
the following measures: Reorient the radio/television receiver’s antenna,
relocate the equipment with respect to the receiver, plug the equipment
and receiver into separate circuit outlets. The user may also wish to
consult a qualified radio/television technician for additional suggestions.
This equipment has been fully tested and complies with all limits for Class
B computing devices pursuant to part 15 FCC Rules and Regulations.
Operation is subject to the following two conditions: (1) This device may
not cause interference, and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
OR
redial
1
flash
redial
2. Remove the batteries (where applicable), and pack product
complete with accessories in the original carton (or equivalent).
abc
jkl
def
(button)
2
8
3
ghi
mno
4
5
6
— Mail prepaid (with proof of purchase) and insured to:
pqrs
wxyz
tuv
7
9
Thomson Digital Technologies Ltd.
c/o Thomson multimedia Ltd.
6200 Edwards Boulevard
Mississauga, Ontario
tone
oper
#
0
*
VOL
Receiver
volume
switch
Canada L5T 2V7
The provisions of this written warranty are in addition to and not a
modification of or subtraction from the statutory warranties and
other rights and remedies contained in any applicable legislation,
and to the extent that any such provisions purport to disclaim,
exclude or limit any such statutory warranties and other rights and
remedies, such provisions shall be deemed to be amended to the
extent necessary to comply therewith.
Telephone Network Information
Should your equipment cause trouble on your line which may harm the
telephone network, the telephone company, where practicable, may notify
you that temporary discontinuance of service may be required. Where
prior notice is not practicable and the circumstances warrant such action,
the telephone company may temporarily discontinue service immediately.
If you are unable to find a qualified servicer for out of warranty
service, you may write to:
Thomson Digital Technologies Ltd.
c/o Thomson Inc.
P.O. Box 0944
The telephone company may make changes in its communications
facilities, equipment, operations or procedures where such action is
required in the operation of its business. If these changes are expected
to affect the use or performance of your telephone equipment, the
telephone company will likely give you adequate notice to allow you to
maintain uninterrupted service.
Installing the Phone
Your telephone should be placed on a level surface such as a desk or table
top, or you can mount it on a wall. A desktop/wall mounting pedestal is
built into the base of the phone.
Indianapolis, Indiana, U.S.A., 46206-0944
Attach your sales receipt to this booklet for future reference. This
information is required if service is needed during the warranty
period.
1. Slide the RINGER volume switch (on the handset) to the desired volume.
2. Set the receiver volume switch (on the handset) to the desired listening
volume.
3. Plug the telephone line cord into a modular wall phone jack.
4. Feed the cord through the grooves as shown in the picture below.
Notice must be given to the telephone company upon termination of your
telephone from your line.
PURCHASE DATE _________________________________________
NAME OF STORE _________________________________________
Wall Mount Installation
Your telephone may also be mounted on a wall plate (not included).
1. Plug the telephone line cord into a modular wall phone jack.
2. Slip the mounting holes on the base over the wall plate posts and
firmly slide the unit down
into place (wall plate not
included).
NOTE: In desktop or
wall mount mode, you
Thomson Digital Technologies Ltd.
© 2006 Thomson Digital Technologies Ltd.
Trademark(s) ® Registered
Model 29253
16156460 (Rev. 3 CAN E/F)
06-41
may want to wrap
the excess telephone
line cord around the
mounting bracket on the bottom of the base.
Marque(s) déposée(s)
Printed in China
|