GE Oven PSB2200 User Manual

Installation  
Instructions  
Advantium® 240V  
Built-In SpeedCook  
Ovens  
PSB2200  
PSB2201  
ZSC2200  
ZSC2201  
ZSC2202  
49-40574-1  
MFL06213302  
02-08 JR  
 
Design Information  
PRODUCT DIMENSIONS AND CLEARANCES NOTE: Appearance will vary by model.  
21-1/2”  
29-3/4”  
19
1”  
13
ADVANCE PLANNING  
TOOLS AND PARTS REQUIRED  
(NOT SUPPLIED)  
#2 Phillips screwdriver  
These ovens may be installed directly into a 30” wide  
oven cabinet.  
Cutout dimensions are NOT the same for installation  
with or without an accessory storage drawer. Make  
sure to use the correct cutout when preparing the  
opening.  
NOTE: Model ZSC2202 CANNOT be installed with an  
accessory storage drawer. See Installation  
Preparation Without an Accessory Storage Drawer  
for this model.  
Hand held drill  
High speed drill bit, 3/32diameter  
3/8slot head screwdriver  
Level  
Saw  
2x4 or 2x2 lumber for installing runners  
or 3/8plywood for floor (if required)  
Wood screws or other hardware for installing  
runner or shelf to support oven (if required)  
Safety glasses or goggles  
IMPORTANT This oven is not approved for  
use above another built-in Advantium Speedcook  
oven, a side by side installation or below a  
countertop.  
For personal safety, this oven cannot be installed  
in a cabinet arrangement such as an island or  
peninsula.  
PARTS SUPPLIED  
6 brass screws (3 required, 3 extra)  
5 color matched screws (4 required, 1 extra)  
Bottom trim  
• The oven must be installed at least 36-3/4" above  
the floor.  
• Allow for clearance to adjacent corners, walls,  
drawers, etc.  
• Cabinets installed adjacent to wall ovens must  
have an adhesion spec of at least 194ºF  
temperature rating.  
The oven must be securely installed in a cabinet  
that is firmly attached to the house structure.  
Weight on the oven door could cause the oven  
to tip and result in injury. Never allow anyone to  
climb, sit, stand or hang on the oven door.  
ELECTRICAL TOOLS AND PARTS  
REQUIRED (NOT SUPPLIED)  
Junction box  
Electrical cable (3-conductor or 4-conductor wire  
as required by local codes)  
UL-listed conduit connectors  
Wire cutters and wire strippers  
If installing the drawer accessory, the drawer must  
be assembled to the oven prior to installation into  
the cabinet. See the Accessory Storage Drawer  
Assembly Instructions.  
3
 
Installation Preparation  
ELECTRICAL REQUIREMENTS  
Single Speedcook Installation  
INSTALL JUNCTION BOX  
The conduit is located at the top right on the back of  
the oven.  
Product rating is 120/208 or 120/240 volt, 60 Hz,  
30 amps. This product must be connected to a supply  
circuit of the proper voltage and frequency and  
protected by a time delay fuse or circuit breaker.  
Power should be supplied from a separate, dedicated  
30-ampere branch circuit. Wire size must conform to  
the requirements of the National Electrical Code or the  
prevailing local code.  
Locate and install the junction box within reach of the  
oven conduit.  
Through the left or right sides of the cabinet wall  
and into adjacent cabinet.  
Or, through the cutout floor.  
Or, in the upper cabinet.  
Combined Speedcook and Wall Oven Installation  
When installed in combination with a GE/Monogram  
single wall oven, use separate electrical junction boxes.  
Refer to single oven installation instructions for  
electrical requirements of that product.  
Cutout  
Height  
These connections must be made by a qualified  
electrician. All electrical connections must meet  
National Electrical Code or prevailing local codes.  
Combined Speedcook and Warming Drawer  
Installation  
When installing the Speedcook oven over a GE or  
Monogram electric warming drawer, a separate 120V,  
60Hz, properly grounded receptacle must be installed.  
See instructions packed with the warming drawer.  
WARNING  
The electrical power to the oven branch circuit  
must be shut off while line connections are being  
made.  
Use copper wiring only.  
Electrical ground is required on this appliance.  
The free end of the green wire (ground wire)  
must be connected to a suitable ground.  
This wire must remain grounded to the oven.  
If cold water pipe is interrupted by plastic,  
non-metallic gaskets, union connections or other  
insulating materials, DO NOT use for grounding.  
DO NOT ground to a gas pipe.  
DO NOT have a fuse in the NEUTRAL or  
GROUNDING circuit. A fuse in the NEUTRAL or  
GROUNDING circuit could result in an electrical  
shock.  
Check with a qualified electrician if you are in  
doubt as to whether the appliance is properly  
grounded.  
Failure to follow these instructions could result in  
serious injury or death.  
4
 
Installation Preparation  
Preparation WITHOUT an Accessory Storage Drawer  
PREPARE THE OPENING  
PREPARE THE OPENING (CONT.)  
The Advantium 240V can be installed in  
combination with other GE/Monogram appliances.  
Always follow each product’s Installation  
Instructions to complete the installation.  
Installation over a GE/Monogram  
Warming Drawer:  
23-1/2”  
Construct  
30”  
Solid Bottom  
Min. 3/8”  
Single Advantium 240V Installation:  
Order a 30” wide single oven cabinet or cut the  
opening in a wall to the dimensions shown.  
Plywood  
Supported  
by 2x4 or 2x2  
Runners all  
Four Sides  
25-1/4”  
23-1/2”  
30”  
2” Min.  
(3” recommended)  
17-1/2”  
25-1/4”  
Per warming  
drawer  
requirement  
17-1/2”  
36-3/4”  
Min.  
Construct  
Base  
Min. 3/8”  
Plywood  
Supported  
by 2x4 or 2x2  
Runners all  
Four Sides  
36-3/4”  
Min.  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven supports  
above the Warming Drawer location do not obstruct  
the required interior depth and height. See Warming  
Drawer installation instructions for details.  
• Always maintain 36-3/4” minimum height from  
the floor to the cutout in any single or combined  
installation.  
• Allow 2-1/8” case trim overlap on the sides and  
7/8” overlap on the bottom of the opening for all  
models. Allow 1-1/4” case trim overlap on the top  
for models PSB2200 and PSB2201 and 3/4”  
overlap on the top for models ZSC2200, ZSC2201  
and ZSC2202.  
• Oven overlaps will conceal cut edges on all sides  
of the opening.  
When installed over a single oven or a warming  
drawer, allow at least 2” between the two openings.  
This separation will provide clearance for bottom  
overlap of the Advantium 240V and the other  
appliance overlaps.  
Construct a solid oven floor of 3/8” min. thick plywood  
supported by 2 x 4 or 2 x 2 runners on all sides.  
• The support must be level and rigidly mounted,  
flush with the bottom edge of the cutout.  
5
 
Installation Preparation  
Preparation WITHOUT an Accessory Storage Drawer  
PREPARE THE OPENING (CONT.)  
Installation over a GE/Monogram Oven:  
PREPARE THE OPENING (CONT.)  
Installation over a GE/Monogram Oven and  
Warming Drawer:  
23-1/2”  
Construct Solid  
Bottom Min.  
3/8” Plywood  
Supported by  
2x4 or 2x2  
30”  
Construct Solid  
Bottom Min.  
3/8” Plywood  
Supported by  
2x4 or 2x2  
30”  
23-1/2”  
Runners all  
Runners all  
Four Sides  
25-1/4”  
Four Sides  
25-1/4”  
17-1/2”  
2” Min.  
(3” recommended)  
2” Min.  
17-1/2”  
(3” recommended)  
Per Oven  
Requirement  
Per Oven  
Requirement  
45-1/4”  
Min.  
45-1/4”  
Min.  
2” Min.  
Per warming drawer requirement  
• If you are replacing a GE/Monogram electric  
double oven with the combined installation of  
an Advantium 240V and a single oven, use the  
dimensions shown. The middle rail separating  
the two openings may need to be larger than  
the 2” minimum shown.  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven  
supports above the Warming Drawer location do  
not obstruct the required interior depth and height.  
See Warming Drawer installation instructions for  
details.  
CAUTION: For personal safety, the mounting  
surface must be capable of supporting the  
cabinet load, in addition to the added weight of  
this approximate 80-pound oven, plus additional  
oven loads of up to 50 pounds or a total weight  
of 130 pounds.  
6
 
Installation Preparation  
Preparation WITH an Accessory Storage Drawer  
NOTE: MODEL ZSC2202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION  
WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.  
PREPARE THE OPENING  
PREPARE THE OPENING (CONT.)  
The Advantium 240V can be installed in  
combination with other GE/Monogram appliances.  
Always follow each product’s Installation  
Instructions to complete the installation.  
Single Advantium 240V Installation (cont.)  
When installed over a single oven or a warming  
drawer, allow at least 2” between the two openings.  
This separation will provide clearance for bottom  
overlap of the Advantium 240V and the other  
appliance overlaps.  
Single Advantium 240V Installation:  
Order a 30” wide single oven cabinet or cut the  
opening in a wall to the dimensions shown.  
Construct a solid oven floor of 3/8” min. thick plywood  
supported by 2 x 4 or 2 x 2 runners on all sides.  
23-1/2”  
30”  
• The support must be level and rigidly mounted,  
flush with the bottom edge of the cutout.  
25-1/4”  
Min.*  
Installation over a GE/Monogram  
Warming Drawer:  
23-1/2”  
Construct  
30”  
Solid Bottom  
Min. 3/8”  
21”  
Plywood  
Construct  
Base  
Supported  
by 2x4 or 2x2  
Runners all  
Four Sides  
25-1/4”  
Min.*  
Min. 3/8”  
Plywood  
Supported  
by 2x4 or 2x2  
Runners all  
Four Sides  
36-3/4”  
Min.  
2” Min.  
(3” recommended)  
21”  
Per warming  
drawer  
requirement  
* For existing cutouts, a maximum width of 28-1/2”  
is acceptable. If the opening is slightly wider,  
secure a furring strip on each side of the cutout  
for securing the oven.  
36-3/4”  
Min.  
• Always maintain 36-3/4” minimum height from  
the floor to the cutout in any single or combined  
installation.  
* For existing cutouts, a maximum width of 28-1/2”  
is acceptable. If the opening is slightly wider,  
secure a furring strip on each side of the cutout  
for securing the oven.  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven  
supports above the Warming Drawer location do  
not obstruct the required interior depth and height.  
See Warming Drawer installation instructions for  
details.  
• Allow 3/4” to 2-1/8” case trim overlap on the sides  
and 7/8” overlap on the bottom of the opening for  
all models. The amount of overlap on the sides  
depends on the actual cutout width. Allow 1-1/4”  
case trim overlap on the top for models PSB2200  
and PSB2201 and 3/4” overlap on the top for  
models ZSC2200, ZSC2201 and ZSC2202.  
• Oven overlaps will conceal cut edges on all sides  
of the opening.  
7
 
Installation Preparation  
Preparation WITH an Accessory Storage Drawer  
NOTE: MODEL ZSC2202 CANNOT BE INSTALLED WITH AN ACCESSORY STORAGE DRAWER. SEE INSTALLATION PREPARATION  
WITHOUT AN ACCESSORY STORAGE DRAWER FOR THIS MODEL.  
PREPARE THE OPENING (CONT.)  
PREPARE THE OPENING (CONT.)  
Installation over a GE/Monogram Oven:  
Installation over a GE/Monogram Oven and  
Warming Drawer:  
23-1/2”  
Construct Solid  
Bottom Min.  
3/8” Plywood  
Supported by  
2x4 or 2x2  
30”  
Construct Solid  
Bottom Min.  
3/8” Plywood  
Supported by  
2x4 or 2x2  
Runners all  
Four Sides  
30”  
23-1/2”  
25-1/4”  
Min.*  
Runners all  
Four Sides  
25-1/4”  
Min.*  
21”  
2” Min.  
(3” recommended)  
2” Min.  
21”  
(3” recommended)  
Per Oven  
Requirement  
Per Oven  
Requirement  
45-1/4”  
Min.  
2” Min.  
45-1/4”  
Min.  
Per warming drawer requirement  
* For existing cutouts, a maximum width of 28-1/2”  
is acceptable. If the opening is slightly wider,  
secure a furring strip on each side of the cutout  
for securing the oven.  
• If you are replacing a GE/Monogram electric  
double oven with the combined installation of  
an Advantium 240V and a single oven, use the  
dimensions shown. The middle rail separating  
the two openings may need to be larger than  
the 2” minimum shown.  
* For existing cutouts, a maximum width of 28-1/2”  
is acceptable. If the opening is slightly wider,  
secure a furring strip on each side of the cutout  
for securing the oven.  
NOTE: Additional clearances between the cutouts  
may be required. Check to be sure the oven  
supports above the Warming Drawer location do  
not obstruct the required interior depth and height.  
See Warming Drawer installation instructions for  
details.  
CAUTION: For personal safety, the mounting  
surface must be capable of supporting the cabinet  
load, in addition to the added weight of this  
approximate 80-pound oven and 30-pound  
drawer, plus additional oven loads of up to 50  
pounds or a total weight of 160 pounds.  
8
 
Installation Instructions  
1 REMOVE THE PACKAGING AND PARTS  
• Remove all packing material and tape.  
• Locate parts package containing mounting screws.  
• Remove the oven from the carton. Do not lift unit by  
handle or conduit. Two people are required to lift  
this oven.  
• Open the door and remove any packaging in oven.  
Owner’s  
Manual  
Rack  
Installation  
Instructions  
Owner’s Manual  
Bottom Trim  
Cooking  
Guide  
5 Color Matched Screws  
(4 required, 1 extra)  
6 Brass Screws  
(3 required, 3 extra)  
Cook Book  
Glass Tray  
Cooking Guide  
Turntable Ring  
IMPORTANT: If installing the Advantium 240V Oven  
with an accessory storage drawer, read the storage  
drawer assembly instructions to assemble the  
products together before proceeding to Step 2.  
Metal Trays (2)  
Metal Grill Tray  
9
 
Installation Instructions  
2 ROUTE CONDUIT THROUGH  
2 ROUTE CONDUIT THROUGH  
CUTOUT  
CUTOUT (CONT.)  
When connecting to a 3-conductor branch  
circuit:  
Connect oven red lead to branch circuit red lead.  
Connect oven black lead to branch circuit black  
lead.  
CAUTION:  
Two people are required to lift  
the oven into the opening. Grasp the bottom at  
front and rear. Discard foam base. DO NOT USE  
HANDLE OR CONDUIT TO LIFT THE OVEN. DAMAGE  
WILL OCCUR.  
Connect oven green ground lead and white lead  
to branch circuit neutral (white or gray).  
With oven in front of the cabinet opening:  
Insert conduit into cabinet opening. Connect oven  
wiring and branch circuit.  
Lift the oven into the opening while continuing to feed  
the conduit in the direction of the installed junction  
box. Be sure the conduit does not get pinched  
between the back of the oven and the cabinet wall.  
Leave oven a few inches forward of the cabinet  
front frame. Do not push the unit all of the way  
into the cutout.  
When connecting to a 4-conductor branch  
circuit:  
Connect oven red lead to branch circuit red lead.  
Connect oven black lead to branch circuit black  
lead.  
Break connection between oven white lead and  
oven green ground lead.  
Connect oven white lead to branch circuit neutral  
lead (white or gray).  
Connect oven green ground lead to branch circuit  
ground lead (green or bare copper).  
(Oven shown without  
accessory storage drawer.)  
WARNING  
Disconnect power to the junction box before  
making the electrical connection.  
Electrical ground is required on this appliance.  
Do not connect the electrical supply until  
appliance is permanently grounded.  
GROUNDING INSTRUCTIONS  
This appliance must be connected to a grounded,  
metallic, permanent wiring system, or an equipment  
grounding connector should be run with the circuit  
conductors and connected to the equipment  
grounding terminal or lead on the appliance.  
Failure to follow these instructions could result  
in fire, personal injury or electrical shock.  
10  
 
Installation Instructions  
4 INSTALL MOUNTING SCREWS  
3 INSTALL BOTTOM TRIM  
NOTE: If installing the Advantium 240 Oven with an  
accessory storage drawer, the bottom trim is not  
required. Proceed to Step 4.  
Align bottom trim tabs to slots in the bottom of the  
oven.  
Slide the oven the remaining way into the opening  
so that the side flanges and control panel are  
against the cabinet frame. Make sure that the oven  
is centered in the opening.  
Secure the bottom trim to the bottom of the oven  
using 3 brass screws provided.  
Open the door, place a turntable tray in the oven  
and make sure that the tray in the unit is level.  
Drill pilot holes through the side flanges.  
Drive the color matched screws into the side  
flanges. It is recommended that the screws  
be hand tightened.  
If installing oven with an accessory storage  
drawer:  
Open the drawer.  
Drill pilot holes through the side flanges.  
Drive color match screws into the side flanges.  
It is recommended that the screws be hand  
tightened.  
5 FINALIZE INSTALLATION  
Turn power on at the source. The interior light  
should come on when the door is opened.  
Refer to Owner’s Manual for operating instructions.  
11  
 
Assembly Instructions  
Advantium® 240V Built-In Accessory Storage Drawer  
JX2200, JX2201, ZX2201  
MODELS AVAILABLE  
BEFORE YOU BEGIN  
Profile Models:  
Read these instructions completely and carefully. Read  
JX2200BB–Black  
the Installation Instructions for the Advantium 240V oven  
completely and carefully for cutout dimensions and  
step-by-step instructions.  
JX2201SS–Stainless Steel  
Monogram Models:  
IMPORTANT Save these instructions for  
ZX2201SS–Stainless Steel  
local inspector’s use.  
NOTE: Advantium 240V Built-In SpeedCook Oven  
model ZSC2202SS CANNOT be installed with an  
accessory storage drawer. See Installation  
Preparation Without an Accessory Storage Drawer in  
the Advantium 240V Built-In SpeedCook Oven  
Installation Instructions for this model.  
IMPORTANT Observe all governing codes  
and ordinances.  
NOTE TO INSTALLER: Be sure to leave these  
instructions with the Consumer.  
NOTE TO CONSUMER: Keep these instructions with  
your Advantium 240V Oven Owner’s Manual for  
future reference.  
SKILL LEVEL: Installation of this appliance requires  
basic mechanical skills.  
PRODUCT DIMENSIONS AND CLEARANCES  
COMPLETION TIME: One hour with the installation  
of an Advantium 240V oven.  
5”  
Proper installation is the responsibility of the installer.  
Allow 15” clearance  
when fully open  
Product failure due to improper installation is not  
covered under the Warranty. See the Advantium  
240V Oven Owner’s Manual for warranty information.  
NOTE: Appearance will vary by model.  
TOOLS REQUIRED  
• #2 Phillips screwdriver  
PARTS SUPPLIED  
• 2 Side Supports  
• Screws  
• Screws (color matched)  
12  
 
ASSEMBLY TO ADVANTIUM 240V BUILT-IN SPEEDCOOK OVEN  
ASSEMBLING THE OVEN TO DRAWER  
(CONT.)  
1 REMOVE PACKAGING AND PARTS  
• Remove the drawer from the carton.  
• Remove all packing material and tape.  
• Open the drawer and remove any parts inside.  
• Locate parts.  
Remove the front two bottom screws on each  
side of the oven and the top center screw on  
each side of the storage drawer.  
C
Side Supports (2)  
Assembly  
Instructions  
Screws (2 Sets)  
2 ASSEMBLING THE OVEN TO DRAWER  
Place storage drawer on a surface with the  
front of drawer hanging over the edge of the  
surface. Not placing the front edge of drawer  
over the edge of the surface may result in  
damage to the drawer since the front edge of  
drawer hangs below the bottom of drawer.  
A
Place the side supports into the tabs on the  
drawer and secure using the screws supplied  
and the screws removed in Step C.  
D
Place the oven on top of the storage drawer.  
Make sure that the back and sides of the oven  
align with the back and sides of drawer.  
B
The oven and storage drawer assembly is now  
ready to be installed. Return to the Advantium  
240V Built-In SpeedCook Oven Installation  
Instructions to complete the installation.  
E
NOTE: The bottom of the oven side flanges will  
sit directly in front of the top of the storage  
drawer side flanges.  
13  
 
14  
 
15  
 
NOTE: While performing installations described in this book,  
safety glasses or goggles should be worn.  
GE Consumer & Industrial  
Appliances  
General Electric Company  
Louisville, KY 40225  
ge.com  
NOTE: Product improvement is a continuing endeavor at  
General Electric. Therefore, materials, appearance and  
specifications are subject to change without notice.  
Printed in Korea  
 

Eiki Projector LC 5300U User Manual
Exmark Lawn Mower Metro 21 Metro 26 User Manual
Frigidaire Air Conditioner FRA084KT7 User Manual
Garmin GPS Receiver 010 00782 2C User Manual
GE Clothes Dryer GFDS355EL User Manual
GE Convection Oven 169140 User Manual
GE Monogram Refrigerator ZISS480DXSS User Manual
Generac Automobile Parts GTV 760 User Manual
Gitzo Camcorder Accessories G1504 User Manual
Goldstar Flat Panel Television 19LG31 User Manual