“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Enclosure Cutout and Product Dimensions (in inches)
10-3/4" Max.
10" Min.
24-3/4"
ZIF36NMRH, Freezer
Handle on the left side, the door swings left to right.
35" Case
36" Overall
ZIF36NMLH, Freezer
Handle on the right side, the door swings right to left.
26-3/4"
84-1/2" Max.
83-1/2" Min.
Caution
73-1/2"
Refrigerators are much heavier at the top than
at the bottom – be extra careful when moving.
4"
• To achieve a flush fit, the finished cutout width must be
at least 36" wide.
*Finished Width
2-1/2
Wall View
Electrical
Area
• In a semi-flush installation, the finished cutout must
be 35-1/2".
6
• The electrical and water locations must be located as
shown for either type of installation.
5
24 3/4" Total
Depth
84-1/2" max
83-1/2" min
Finished
75" From Floor
to Bottom
of Electrical
Area
24-3/4"
Case
35"
Case
Width
Depth
Opening
5
5
Water Supply
3-1/2
3-1/2
84*
*36" for a flush installation.
35-1/2" Min. for a semi-flush installation.
Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width. See installation examples.
36"
Frame to Frame
26-1/4"
Including
Handle
*Shipped at 84" installation height. Can be adjusted to
83-1/2" or 84-1/2" with Grille Panel Kits.
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
GEAppliances.com or call
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Installation at End of Run
1/2" Thick
Side Panels
Refrigerator
Cabinet
36"
37"
Finished Dim.
Roughed-In Dim.
Refrigerator Door
Cabinet
Note: 1/2" thick side panels shown. Side
panels can be any thickness. Add side
panel thickness to outside trim width
(36" or 72" for two models) to calculate
the rough-in dimension. The leading
(front) edge must be finished to match
surrounding cabinetry.
1/2" Thick
Side Panels
Finished Dim.
72"
73"
Rough-In Dim.
1/4" Thick
Side Panels
Finished Dim.
Rough-In Dim.
71 1/2"
72"
Refrigerator and Freezer
installed side-by-side
Side-By-Side Installation of Freezer and Refrigerator
*Finished Width
Electrical
2 1/2"
6"
Wall View
28 1/2"
6"
84"
5"
5"
24 3/4" Total
Depth
84 1/2" max
83 1/2" min
Finished
75" From Floor
to Bottom
of Electrical
Area
Opening
5"
Water Supply
36"
26"
3 1/2"
Freezer
Refrigerator
24-3/4"
36"
*72" min. for a flush installation
71-1/2" min. for a semi-flush installation
For a complete food storage center, install a Monogram
Freezer and Refrigerator side-by-side. For even more
capacity, install two refrigerators and/or two freezers.
• Order ZUG75 Unified Grille Panel Kit for one
continuous 3/4" custom grille panel.
Note: Additional cutout width may be required when side
panels are used. Add side panel thickness to the finished
cutout to calculate rough-in width.
• The electrical and water locations must be located
as shown for either type of installation. A separate
115V, 60Hz., 20 amp power supply is recommended
for each product.
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
GEAppliances.com or call
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Custom Panel Dimensions
A
Custom Grille Panel Dimensions
IMPORTANT: Maximum
weight for custom door
panel is 67 pounds and
9 pounds for the grille
panel.
Width
Height
Custom Grille Panels
Custom
Panel
1/4" THICK CUSTOM GRILLE PANEL
Panel
Width
Panel Height
to Fit Installation Height
B
83-1/2"
7-1/2"
84"
8"
84-1/2"
8-1/2"
35-1/8"
Rout for 3/4"
Handle Kits Only
See Details
Note: The grille panel frame is factory assembled
for 84" installation height. Order ZGC2 Grille Panel
Kit when installation height is more or less than 84".
3/4" THICK CUSTOM GRILLE PANEL
Requires ZKTR36 Trim Kit
CUSTOM DOOR PANEL SIZES
SIZES
A
B
Panel
Width
Panel Height
to Fit Installation Height
1/4" Panels
3/4" Panels
35-1/16"
35-1/16"
68-7/8"
68-15/16"
83-1/2"
7-3/4"
84"
84-1/2"
8-3/4"
3/4" Panels
(custom handles)
35-1/4"
8-1/4"
35-1/4"
68-15/16"
Note: A grille panel support is included with the
ZKTR36 trim kit and fits all installation heights.
Routing Detail
ZUG75 Grille Panel Dimensions
For Handle Kits Only
Rout Back Side of Panel
1-13/16"
This Grille Panel Kit should be used in combination
with ZKTR36H and ZKTR36RH, 3/4" panel kits.
Width
Height
ZUG75 Grille Panel
3/4" THICK CUSTOM GRILLE PANEL
Requires ZUG75 Trim Kit
1/4"
Max.
Appearance Side
Panel
Width
Panel Height
to Fit Installation Height
Rout the panel when installing a ZKHTR1 Custom
Handle Kit or ZKHTRSS1, Tubular Stainless Steel
Handle Kit.
83-1/2"
7-3/4"
84"
84-1/2"
8-3/4"
71-3/8"
8-1/4"
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
®
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
25"
Minimum
to Wall
Clearances
• Factory set for a 130° door swing. Order WX14X99
adjustable door stop to reduce swing to as little
as 90°.
90° Door Swing
130° Door Swing
When Installed into a corner:
Allow 25" for a full 130° door swing. Allow 15" for
pan removal. Allow 4" min. clearance when
door swing is adjusted to a 90° opening for pan
access, but pan removal is restricted.
36-3/4"
4" Min.
to Wall
90° door swing with
optional WX14X99
door stop.
0"
When installing an All-Refrigerator and All-Freezer
side-by-side, allow 25" for a full 130° door swing,
or 15" min. on the hinge sides for pan access.
25"
Min. to
Wall
25"
Min. to
Wall
130° Door Swing
130° Door Swing
ZUG75 Unified Grille Panel Kit is available for side-by-side
installations. See Trim Kit descriptions.
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
GEAppliances.com or call
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Design Information
Flush or Semi-Flush Enclosure Installation
Semi-Flush Installation
True Flush Installation
True Flush Installation
In a flush installation,
the freezer doors
Semi-Flush Installation
These freezers can
also be installed
will align evenly
semi-flush into an
enclosure using the
minimum cutout width.
The case trim creates
a frame around
with the front face
of adjacent cabinet
doors. The freezer
blends into the
0"
surrounding cabinetry.
the opening.
3/4"
Monogram built-in refrigerators and freezers can be
installed flush with typical 24-3/4" deep cabinetry.
Side Panel Requirements:
• Side panels are not required whenever the refrigerator or
freezer is installed into an enclosure or between pantry and
oven cabinets.
When installed semi-flush, the case trim will conceal
slight gaps around the enclosure. The refrigerator
will project forward approximately 3/4" beyond the
front face of surrounding cabinetry.
• Side panels are required whenever the sides of the product
are exposed.
• Side panel sizes vary depending on the type of installation being
made.
To accomplish an attractive installation, you must:
1. Determine the need for side panels.
2. Determine side panel thickness.
3. Order matching side panels from the cabinet manufacturer.
Be sure to provide the exact dimensions.
®
For answers to your Monogram, GE Profile™ or
GE appliance questions, visit our website at
Listed by
Underwriters
Laboratories
Specification Revised 4/05
110156
GEAppliances.com or call
R
GE Answer Center® service, 800.626.2000.
“
Monogram.
ZIF36NM – GE Monogram 36" Built-In All-Freezer
Features and Benefits
• 21.9 Cu. Ft. Freezer Capacity
• Wire Freezer Shelves (5 Adjustable,
1 Fixed, 1 Full-Width Fixed)
• Wire Baskets with Full-Extension Slides
(2 Regular, 4 Large)
• 2 Extra Large Wire Baskets with
Easy Access Lid and Full Extension Slides
• 8 Door Bins and Gallon Storage
• Automatic Defrost Sealed System Design
• Full Extension Slides
• Door Panels Required
• Model ZIF36NMRH – Door panels required
(right-handed door swing)
• Model ZIF36NMLH – Door panels required
(left-handed door swing)
Specification Revised 4/05
110156
|