24V DRIVE, HIGH SPEED LINE THERMAL PRINTER
4” MECHANISM, WITH OR WITHOUT CUTTER
FTP-642MCL001/002
FTP-642MCL301/302
■ OVERVIEW
FTP-642MCL/FTP-622DCL Series is an ultra high speed line thermal
printer driven by 24 VDC, printing on 4-inch wide paper (112 mm/114
mm) .
This printer is compact and light weight, and the design allows easy
head maintenance, head cleaning and head replacement.
This printer is suitable for a variety of applications, such as POS
terminals, ticket machines, coupon machines, label printers, medical
instruments, etc. A printer with a specially designed cutter is also
available.
FTP-642MCL001
■ HIGHLIGHTS
• Ultra high speed printing
It can print at 80 mm/s (640 dotlines/s) maximum by using Fujitsu
Components' unique head drive control.
• Compact and lightweight
This printer has a low profile of only 20 mm, and a light weight of
approximately 125 g.
• Low power consumption
The peak current for head driving is approximately 4.1 A (at 80
mm/s printing speed, 50% printing ratio).
FTP-622CU101
• Easy head access
It is designed for easy head cleaning and head replacement.
• Paper auto loading function
Thermal paper can be loaded without head-up lever operation.
• ESC/POSTM*1 Commands
The commands conform to ESC/POSTM.
• Auto Cutter
Printer with auto cutter (full cut/partial cut ) is also available.
• UL Recognized
File No.E171434
*1 ESC/POSTM is a registered trademark of SEIKO EPSON Corp.
FTP-622DCL001
1
FTP-642MCL001/002/301/302
(Continued)
Item
Specifications
Part number
Interface
FTP-642MCL001/002
FTP-642MCL301/302
Centronics (ESC/POSTM), RS232C
24VDC ± 5%, Voltage
2
Current : average*
(
): Peak
For head
1.61 (2.03) A (at 80 mm/s printing speed, 25% printing ratio)
1.17 (2.03) A (at 50 mm/s printing speed, 25% printing ratio)
1.08 (1.16) A (at 30 mm/s printing speed, 25% printing ratio)
Power supply
For motor
24VDC ± 5%, 1.0 A maximum
24VDC ± 5%, 1.0 A maximum
For cutter
----------
For logic
5VDC ± 5%, 0.5 A maximum
138 (W) × 48 (D) × 20 (H) mm (excluding lever)
131 (W) × 89 (D) × 24 (H) mm
approximately 125 g
Mechanism (cutter)
Interface board
147 (W) × 69 (D) × 42 (H) mm (w/cutter)
Dimension
Weight (Mechanism+Cutter)
Mechanism
approximately 450 g (w/cutter)
Pulse durability : 1 × 108 pulse/dot (using Fujitsu Takamisawa's standard
driving method)
Wear resistance
: 50 km (at 25% printing ratio)
Expected life
Cutter
----------
3 × 105 cuts
3
Operating temperature 0 to +50°C*
Environmental
conditions
Operating humidity
Storage temperature
Storage humidity
Head temperature
Paper out/Mark detect
Head-up
20 to 85% RH (no condensation)
–20 to +60°C (excluding paper)
5 to 95% RH (no condensation)
By thermistor (applied energy control, abnormal temperature detection)
By photointerrupter
Detection
By microswitch
For front insertion use (112 mm width) : FTP-040PU001, FTP-040P0701
For rear insertion use (114 mm width) : FTP-040P0020, FTP-040P0702
*Recommended papers
Recommended thermal sensitive paper
· Oji paper
· NIPPON paper
· MITSUBISHI paper Mills
: PD150R, PD160R, PD170R
: TF50KS-E,TF60KS-E,TF60KJ-R
: P220VBB-1, AFP-235
*1: There may be exceptions.
*2: 24 VDC, minimum head resistance.
*3: Guarantee: +5°C ~+40°C.
3
FTP-642MCL001/002/301/302
■ DIMENSIONS
Mechanism
PAPER INSERTION(MCL001)
HEAD UP LEVER(AT HEAD DOWN)
20.1
CENTER OF PAPER
PAPER
INSERTION
(MCL002)
HEAD CONNECTOR
106.4(POSITIONING HOLE PITCH)
+
1
71.8–
65.7
Unit: mm
(137.5)
Mechanism with cutter
3—M 3(FIXING HOLE FROM UPPER SIDE)
CENTER OF PAPER
MCL301
PAPER
INSERTION
MCL302
PAPER
INSERTION
93.0
106.4(POSITIONING H0LE)
73.0
147
71.8±1
(75.3)
(80.6)
Note: all dimensions are nominal value.
Unit: mm
4
FTP-642MCL001/002/301/302
Interface board
130.8
120.7
116.8
87.6
19.1
5.1
5.1
CN2**
CN5
CN3
4—ø3.6
CN10
CN11*
CN13
5.1
5.1
43.2
86.4
105.4
120.7
*CN11 on FTP-622DCL011/111 & 622DSL011/012/112 only
**CN2 on FTP- 622DSL only
Unit: mm
5
FTP-642MCL001/002/301/302
■ CONNECTOR PIN ASSIGNMENT FOR PRINTER MECHANISM
1. Thermal Head
Head side : B16B-PH-K-S-2.2 (J.S.T.) or equivalent
Board side: PHR-16 (J.S.T.) or equivalent
No. Signal Comment
1
2
VH
VH
Power for head
Power for head
3
GND Head ground
4
GND Head ground
5
STB1 Print enable signal 1
STB2 Print enable signal 2
STB3 Print enable signal 3
6
7
8
TH*1
STB4 Print enable signal 4
LAT Print data latching signal
Temperature detection
9
10
11
12
13
14
15
16
STB5 Print enable signal 5
VDD Power for logic
CLK
DIN
Data transmission clock
Print data output signal
GND Head ground
VH Power for head
*1: Symbol: " " means a negative logic signal
Thermal head heat sink
Motor
Head up level
1, 2, 3, ......................................15, 16
Connector Pin No.
2. Motor connectors
3. Sensor connectors
Motor side : PHR-4 (J.S.T.) or equivalent
Board side : B4B-PH-K-S (J.S.T.) or equivalent
Sensor
: PHR-5 (J.S.T.) or equivalent
Board side : B5B-PH-K-S (J.S.T.) or equivalent
No. Signal Comment
No. Signal Comment
1
2
3
4
B
B
A
A
Stepping motor coil excitation
Stepping motor coil excitation
Stepping motor coil excitation
Stepping motor coil excitation
1
2
3
4
5
VSEN Power for paper sensor
PHE Photo interrupter emittor
PHK Photo interrupter cathode
SW1 Head up detect switch 1
SW2 Head up detect switch 2
6
FTP-642MCL001/002/301/302
4. Cutter
Mech side : EHR-4 (J.S.T.) or equivalent
Board side : B4B-EH (J.S.T.) or equivalent
No Cable Color
Name
1
2
3
4
White
White
Red
Home position 1
Home position 2
Motor energizing signal M+
Motor energizing signal M-
Black
■ FUNCTION
ITEM
ITEM
1.
2.
3.
4.
5.
6.
7.
Test printing
8.
Cutter trouble detection
Motor power save
Paper-out detection
9.
10.
11.
12.
13.
14.
Paper near end detection
Mark detection
Head-up detection
MCU trouble detection
Power on/off sequence protection
Motor protection
Abnormal temperature detection of thermal head
Blown fuse detection
Abnormal voltage detection of head
Hardware timer
■ INTERFACE, COMMAND, OPTIONS
Please refer to the FTP-622DCL DATA SHEET and the FTP-622DSL DATA SHEET for Interface, Command, and
Options.
Europe
Japan
Fujitsu Components Europe B.V.
Diamantlaan 25
2132 WV Hoofddorp
Netherlands
Fujitsu Component Limited
Gotanda-Chuo Building
3-5, Higashigotanda 2-chome, Shinagawa-ku
Tokyo 141, Japan
Fujitsu Components
International
Headquarter
Offices
Tel: (31-23) 5560910
Fax: (31-23) 5560950
Email: [email protected]
Tel: (81-3) 5449-7010
Fax: (81-3) 5449-2626
Email: [email protected]
Asia Pacific
North and South America
Fujitsu Components America, Inc.
250 E. Caribbean Drive
Sunnyvale, CA 94089 U.S.A.
Tel: (1-408) 745-4900
Fujitsu Components Asia Ltd.
102E Pasir Panjang Road
#04-01 Citilink Warehouse Complex
Singapore 118529
Tel: (65) 6375-8560
Fax: (1-408) 745-4970
Fax: (65) 6273-3021
Email: [email protected]
Email: [email protected]
© 2004 Fujitsu Components America, Inc. All company and product names are trademarks or registered
trademarks of their respective owners. Rev. 11/15/2004.
7
|