OPERATOR PANEL
TTL-IC
This guide is prepared to instruct the user on the switch and jumper
settings in the MCE3064SS/MCF3064SS/MCE3130SS when you install
your MCE3064SS/MCF3064SS/MCE3130SS.
CNH2 (EXTERNAL SWITCH
SETTING)
1
2
Note; Factory default settings are marked with ✻.
3
Pin#
Function
Cartridge-in detection
SCSI ID 4
Open
—
Short
—
4
1
2
3
4
5
6
7
8
9
Layout of PCA
SCSI ID Setting
Table 1
SW1-01 SW1-02 SW1-03
5
—
—
SCSI ID
—
—
6
LED source (+5 V)
SCSI ID2
0
1
2
3
4
5
6
7
✻
Off
Off
Off
Off
On
On
On
On
Off
Off
On
On
Off
Off
On
On
Off
On
Off
On
Off
On
Off
On
MCE3064SS, MCF3064SS,
MCE3130SS
Magneto-Optical Disk Drives
—
—
7
—
—
LED source (–)
SCSI ID1
8
—
—
9
—
—
Signal to eject cartridge
Ground
10
11
12
13
14
15
16
—
—
Device type mode
Fixed disk
Disabled
Enabled
—
MO
10 SCAM mode
Enabled
Disabled
—
11 Write verify mode
12 Ground
Installation Guide
Installationsanleitung
Guide d'installation
13 Macintosh mode
14 SCSI type 0
Disabled
SCSI 2
Disabled
—
Enabled
SCSI 1
Enabled
—
SW1 AND CNH2 SETTINGS
Switch 1 sets the SCSI ID and some drive functions and CNH2 sets
additional drive functions.
15 Terminating resister mode
16 Ground
0V
SW1
Key#
Note: The cable length must not exceed 30cm.
Function
Key on
Key off
01
02
03
04
05
06
07
08
✻
✻
✻
Device Driver
————
————
SCSI ID (see table 1 above)
You need to install Fujitsu's device driver to avoid the 2KB sector
problem in Windows9x and the OS-timeout-problem in Windows9x and
NT3.51/4.0.
SCSI data bus parity check
Write cache mode
Device type mode
Spindle automatic stop mode
Factory test (Not to be set by user)
Enabled
Enabled
MO
Enabled
Enabled
✻
✻
Disabled
Disabled
Fixed Disk
Disabled
Disabled
✻
MCE3064SS/MCF3064SS/MCE3130SS HANDLING AND MAINTENANCE
Orientation
Cleaning lens and media
✻
✻
The drive can be installed in one
of three orientations; either PCA
up or on either side edge.
recommendation
Clean the lens on the drive head
and the disk media once every
three months. More frequent
cleaning may be required in a
dirty environment. Use the
Fujitsu head cleaning kit and
media cleaning kit. Head
cleaning kits from other vendors
will not work.
CNH1 (TERMINATING POWER AND SCSI TERMINATION)
Terminal CNH1 uses shorting bars to set the power source and to
enable or disable SCSI termination.
Ejecting cartridge
Cartridges can be ejected by
pressing the eject key or by a
SCSI eject command. Never
eject a cartridge mechanically
except in an emergency.
Pin# Function
Short
Open
Power supplied by 1–2 3–4
1–2 Power supplied by Supplied Not
Drive
Short Open
Open Short
Short Short
drive
supplied
Host controller
3–4 Power supplied by Supplied Not
Drive and Host
controller
host controller
supplied
WORLD WIDE WEB SITE
Corporate http://www.fujitsu.co.jp/
5–6 SCSI termination Enabled Disabled
enabled
SINGAPORE http://www.fujitsu-computers.com.sg/
USA
CANADA
COPYRIGHT FUJITSU LIMITED
SEPT. 1999
C156-E117-02XA
|