FRIGIDAIRE
C O M M E R C I A L
COMMERCIAL FREEZER/REFRIGERATOR
GLASS DOOR REFRIGERATOR
TABLE OF CONTENTS
Product Registration………………………………….…..... 2
Important Safety Instructions……………………….…..... 2
Electrical Information…………………………………........ 3
Caster Installation and Setup (Glass Door)................... 3-4
Caster Installation and Setup (Non-Glass Door).......... 5-6
Appliance Start-up…………………………………............. 6
Features……………………………………………………..... 6-7
Routine Maintenance……………………………………..… 7
Energy Conservation Measures………………………...... 7
Troubleshooting Guide…………………………………...... 8-9
Wiring Diagram……………………………………………....10
Warranty……………………………………………………... 11
READ AND SAVE THESE INSTRUCTIONS
297121600 (June 2006)
CASTER INSTALLATION AND SET-UP
(Glass Door Only)
Inspect the underside of the cabinet and packaging for damage
such as a fork truck can cause. If hidden damage is found after
uncrating, immediately call the delivery carrier and request an
inspection. Retain all packaging and crating materials until the
inspection is complete.
Electrical Information
These guidelines must be followed to ensure that safety
mechanisms in the design of this appliance will operate
properly.
Avoid fire hazard or
electric shock. Do not use an extension cord
or an adapter plug. Do not remove any
PARTS AND ACCESSORIES
Check to make sure that you have received the box containing
all of the components listed below.
prong from the power cord.
A
C
G
E
D
F
B
H
A
B
C
D
CASTER RAIL (2)
LOCKING NUT (8)
CARRIAGE BOLT (8)
BOLT (4)
E
F
G
H
WASHER (4)
SPACER PLATE (2)
SWIVEL CASTER (2)
FIXED CASTER W/ BRAKE (2)
TOOLS NEEDED
You will need the following tools to assemble and install the
casters to the unit.
• Refer to the serial plate for correct electrical rating. The
power cord of the appliance is equipped with a three-prong
grounding plug for protection against shock hazards. It must
be plugged directly into its own properly grounded three-prong
receptacle, protected with a 15 amp time delay fuse or circuit
breaker. The receptacle must be installed in accordance with
the local codes and ordinances. Consult a qualified electrician.
Receptacles with Ground Fault Circuit Interrupters (GFCI) are
NOT RECOMMENDED. DO NOT USE AN EXTENSION
CORD OR AN ADAPTER PLUG.
• If the voltage varies by 10 percent or more, appliance
performance may be affected. Operating the appliance with
insufficient power can damage the motor. Such damage is
not covered under the warranty. If you suspect your voltage is
high or low, consult your power company for testing.
• To prevent the appliance from being turned off accidentally,
do not plug the unit into an outlet controlled by a wall switch
or pull cord.
3/8” AND 1/2” INCH
SOCKET WRENCH
ADJUSTABLE WRENCH
OR PLIERS
1/2” INCH FIXED
WRENCH
UNCRATING AND SET-UP
• Remove carton and all loose parts from inside of the unit.
• Carefully tip the unit onto its back with the help of an assistant.
Lay the unit gently to rest on blocks to avoid damaging the
condensate drain hose and the plastic raceway that covers
the evaporator tubing on the back of the cabinet.
• Remove and discard the wood skid from the bottom and the
four (4) screws using a 3/8" socket wrench (see Fig. 1).
• Using a large adjustable wrench, remove and discard the two
(2) black plastic leg levelers by turning it counterclockwise (see
Fig. 2).
• DO NOT pinch, knot, or bend the power cord in any manner.
SCREWS
Other Precautions
• NEVER unplug the appliance by pulling on the power cord.
Always grip the plug firmly and pull straight out from the
receptacle.
LEG LEVELER
• To avoid electrical shock, unplug the appliance before
cleaning.
NOTE: Turning the control to “OFF” turns off the compressor
but does not disconnect power to other electrical components.
WOOD SKID
Figure 2
Figure 1
3
• Remove bottom door support bracket and screw opposite the REAR SWIVEL CASTER INSTALLATION
door hinge using a 3/8" socket wrench (see Fig. 3).
• Place a washer on one of the four long bolts and then feed the
bolt through the hole in one of the swivel casters (see Fig. 6).
• Next, insert that same caster bolt through the hole on the metal
spacer plate and then thru the rear hole of the caster rail (see
Fig. 7).
• Thread the caster bolt into the hole in the bottom-most foot
pad on the unit.
DOOR
SUPPORT
BRACKET
• Tighten both top and bottom bolts securely using a 1/2 inch
fixed or socket wrench.
• Repeat the same procedure on the left hand side. After
installation, carefully tip the unit up with the help of an assistant.
Figure 3
Bolt
SPACER
PLATE
FRONT FIXED CASTER INSTALLATION
• Put two (2) carriage bolts through the rear (non-brake) side of
the fixed caster and hold the carriage bolts loosely in place by
threading several turns on each of the locking nuts. Do not
tighten the bolts yet.
Washer
Swivel
Caster
• Hold the caster in position, insert the carriage bolt heads into
slots A & B near the front of the caster rail and slide the caster
back.
Figure 7
Figure 6
• Insert the two (2) front carriage bolts thru the top side of the
caster rail and then thru the front holes on the caster. Attach
locking nuts to each.
• Tighten all locking nuts securely using a 1/2 inch wrench (see
Fig. 4).
• Repeat the same procedure for the other fixed caster.
BRAKE
LOCKING NUTS
FRONT OF
CASTER RAIL
FIXED CASTER
Figure 4
CARRIAGE
BOLTS
CARRIAGE BOLTS
SLOTS A&B
CASTER RAIL INSTALLATION
• Place a washer onto one of the four long bolts and slide bolt
through the hole located just behind the fixed caster at the
front of caster rail.
• Align the caster rail assembly with the right hand side of the
unit. Make sure the fixed caster is positioned toward the front
of the unit.
• Align the bolt with the threaded hole in the front right foot pad
of the unit. Thread the bolt into the hole until finger tight (see
Fig. 5).
WASHER
BOLT
WASHER
Figure 5
BOLT
4
CASTER INSTALLATION AND SET-UP (NON-GLASS DOOR)
INSPECTION FOR DAMAGE
CASTER RAIL INSTALLATION
x Place a washer onto one of the six long bolts and slide bolt through the
hole located at the front of caster rail.
Inspect the underside of the cabinet and packaging for damage such as a
fork truck can cause. If hidden damage is found after uncrating,
immediately call the delivery carrier and request an inspection. Retain all
packaging and crating materials until the inspection is complete.
x Align the caster rail assembly with the right hand side of the unit.
x Align the bolt with the threaded hole in the front right foot pad of the
unit. Thread the bolt into the hole until finger tight (see Fig. 3).
PARTS AND ACCESSORIES
Check to make sure that you have received the box containing all of the
components listed below.
F
D
A
B
Figure 3
C
E
G
REAR SWIVEL CASTER INSTALLATION
x Place a washer on one of the six long bolts and then feed the bolt
through the hole in one of the swivel casters (see Fig. 4).
x Next, insert that same caster bolt through the hole on the metal spacer
plate and then thru the rear hole of the caster rail (see Fig. 5).
x Thread the caster bolt into the hole in the bottom-most foot pad on the
unit.
A
B
C
D
CASTER RAIL (2)
TAPPING PLATE (2 )
BOLT (6)
E
F
SWIVEL CASTER (2)
SPACER PLATE (4)
SWIVEL CASTER W/ BRAKE (2)
G
WASHER (6)
TOOLS NEEDED
You will need the following tools to assemble and install the casters to the
unit.
x Tighten both top and bottom bolts securely using a 1/2 inch fixed or
socket wrench.
x Repeat the same procedure on the left hand side.
3/8” AND 1/2” INCH
SOCKET WRENCH
ADJUSTABLE WRENCH
OR PLIERS
1/2” INCH FIXED
WRENCH
BOLT
UNCRATING AND SET-UP
WASHER
x
x
Remove carton and all loose parts from inside of the unit.
Carefully tip the unit onto its back with the help of an assistant. Lay the
unit gently to rest on blocks to avoid damaging the condensate drain
hose and the plastic raceway that covers the evaporator tubing on the
back of the cabinet.
SWIVEL
CASTER
x
x
Remove and discard the wood skid from the bottom and the four (4)
screws using a 3/8” socket wrench (see Fig. 1).
Figure 4
Figure 5
Using a large adjustable wrench, remove and discard the two (2) black
plastic leg levelers by turning it counterclockwise (see Fig. 2).
FRONT SWIVEL CASTER INSTALLATION
x Place the tapping plate between the front bottom of the cabinet and
caster rails as depicted in Figure 6. Make sure the tapped holes in the
tapping plate align with the center slot in the caster rail.
x Next, place a washer on one of the six long bolts and then feed the bolt
through the hole in one of the swivel casters (see Fig. 4).
x Then, place the spacer plate on the caster and thread the caster bolt
into the hole in the tapping plate.
SCREWS
LEG LEVELER
x Tighten securely using ½” fixed or socket wrench.
x Repeat the same procedure on the left hand side. After installation,
carefully tip the unit up with the help of an assistant.
WOOD SKID
Figure 2
Tapping Plate
Figure 1
Figure 6
5
Appliance Placement
Features
Leave a one (1) inch space on all sides and the back of the
cabinet for ease of installation, proper air circulation and electrical
connections. DO NOT block the front grill on the lower front
of your appliance. Sufficient air circulation is essential for the
proper operation of your appliance. Choose a place that is near
a grounded electrical outlet. For the most efficient operation,
the appliance should be located where surrounding temperatures
will not drop below 40ºF (5ºC) or exceed 110ºF (43ºC). Additional
compressor heaters are not recommended.
NSF and FDA Approved Adjustable Shelving
This appliance is provided with NSF and FDA approved heavy
duty epoxy powder coated adjustable shelves. The one with the
wires that are angled on the front and back goes on the floor of
the cabinet. The others are placed in the adjustable stainless
steel shelf supports that clip into the shelf support strips on each
side of the interior. Make sure to place the shallow shelf in the
upper-most posi
Insulation
The insulated space of this cabinet is sealed to maintain peak
efficiency. Holes drilled in the cabinet may destroy that seal and
damage electrical wiring located in the insulated space.
DAMANGED ELECTRICAL WIRING OR WET INSULATION
CAUSED BY DRILLING WILL VOID THE WARRANTY.
Appliance Start-up
Once the appliance has been located in its permanent location
and the proper power and grounding has been provided, the
following items must be checked or completed:
Front Fixed and Rear Swivel Casters
Cool Down Period
Glass door unit come with two (2) front fixed casters with
brakes and two (2) rear swivel casters. Non-glass door unit
comes with two (2) front swivel casters with brakes and two (2)
rear swivel casters. The casters allow the appliance to be
moved with ease and then locked in position at its desired
location.
For safe food storage, allow 24 hours for the appliance to cool
down completely before loading with food. The appliance will
run continuously for the first several hours. Do not place any
food in the appliance until after the first 24 hours of operation.
Thermostat Setting
The appliance is shipped from the factory
with the thermostat set at about the mid-
point of the operating range.Adjustments
colder or warmer can be made after the
appliance has been running for at least
8 hours. Allow at least 8 hours for
temperature stabilization before re-
adjusting the thermostat.
Defrost Setting
The appliance is designed to defrost automatically every 12
hours. To set the time of defrost, wait until the desired time to
defrost. With the notch on the timer knob aligned with the line
on the bracket (Fig. A), turn the defrost timer knob clockwise
slowly. The timer will click several times, then once loudly, at
which point the defrost cycle begins. The timer knob will advance
through the defrost cycle, then click loudly at the end of the cycle
(Fig. B). The appliance will defrost automatically every 12 hours
after the first defrost cycle.
Adjustable Temperature Control
The adjustable cold control is located on the top left side of the
evaporator housing inside the unit. “5” is the medium
(recommended) setting and “9” is the coldest setting.
Fig. B
Fig. A
Position of knob at end
of defrost cycle (Second
click)
Position of knob before
turning clockwise to start
defrost cycle (First click)
6
scratch the appliance surface when removing adhesive labels.
Any glue left from the tape can be removed with a mixture of
warm water and mild detergent or touch the residue with the
sticky side of tape already removed. DO NOT REMOVE THE
SERIAL PLATE.
NSF Certified Temperature Gauge
This appliance is equipped with an NSF certified temperature
gauge to display cabinet internal temperature. The temperature
gauge is located on the top right side of the evaporator housing
inside the unit.
Condensate Pan
Some models have a condensate pan in a fixed position located
behind the toe grill. This must not be removed from under the
cabinet. If the pan is removed, condensate will drop onto the
floor.
POWER FAILURE
DO NOT open the appliance lid unnecessarily if the
appliance is off for several hours.
If a power failure occurs, pack seven or eight pounds of dry ice
into the appliance every 24 hours. Look in the Yellow Pages
under “Dry Ice”, “Dairies”, or “Ice Cream Manufacturers” for local
dry ice suppliers. Always wear gloves and use caution when
handling dry ice.
Fluorescent Lamp (Glass Door Models)
The Glass Door Refrigerator is equipped with a 17 watt
fluorescent lamp. A ballast – lamp mismatch may result in poor
or no lighting.
If the lamp fails, replace with a lamp of the same type and
wattage. Also, replace a lamp that flickers continuously. This
could damage the ballast.
Energy Conservation Measures
This appliance is designed for efficiency with heavy foam
insulation. However, there are things that the user can do to
maintain the appliance in operating condition.
Turning the light off, when not in use, will save energy. However,
frequent ON-OFF cycling will reduce the lamp life.
• Do not operate the appliance any colder than necessary to
maintain safe, product storage temperatures.
• Make sure the appliance is located to prevent direct exposure
to sunlight, air ducts, etc.
• Keep the door closed except for normal use. Inspect the door
often to see that it self-closes and the gaskets are in good
condition.
Use only NSF certified lamp which can be ordered from your
Frigidaire Commercial Service Center by calling 1-866-738-1640.
Interior Light (Stainless Steel Door Models)
The Stainless Steel Door models are equipped with a 40 watt
bulb that lights up when the door is opened. If the bulb goes
bad, replace with bulb of the same type and wattage. This is a • Do not overstock the product in the cabinet because it will
special bulb with a shatterproof coating. Use only an NSF certified block the normal air flow.
bulb of the same type and wattage which can be ordered from • Have at least annual inspections by a qualified service
your Frigidaire Commercial Service Center by calling 1-866-738-
1640.
company to see that the refrigerant charge is correct.
• This appliance operates more efficiently in a cooler ambient
than in a hot ambient. Try to maintain an ambient below 80ºF
(27ºC) and 65% RH (Relative Humidity) for maximum efficiency.
Other Features
• NSF Certified top mounted evaporator.
• 2 ½ thick urethane foam cabinet insulation.
• Torsion spring door closer (Glass Door models).
• Stainless steel evaporator housing.
Periods of Non-use and Moving Tips
Leave the appliance operating during periods of non-use of less
than three (3) weeks.
• Removable stainless steel drain cover.
• Heavy duty front grill.
Long Periods of Non-use
• Heavy duty commercially rated electrical harness.
• Heavy duty removable stainless steel shelf supports.
If the appliance will not be used for several months:
• Remove all food and unplug the power cord.
• Clean and dry the interior thoroughly.
Routine Maintenance
• Leave the appliance door open slightly, blocking it open if
necessary, to prevent odor and mold growth.
Cleaning the Interior
Moving
Be sure to turn the temperature control to “OFF” and unplug the
electrical cord. Wash the inside surface of the storage area with
warm water and baking soda solution (about one tablespoon of
baking soda per quart of warm water). Rinse thoroughly with
clean, warm water and wipe dry.
When moving the appliance , follow these guidelines to prevent
damage:
• Disconnect the power cord plug from the wall outlet.
• Remove foods, then defrost, and clean the appliance .
• Secure all loose items such as base panel, baskets, and
shelves by taping them securely in place to prevent damage.
• In the moving vehicle, secure appliance in an upright position
to prevent movement. Also, protect outside of appliance with
a blanket or similar item.
Cleaning the Exterior
Wipe the cabinet exterior occasionally with a cloth dampened in
mild detergent and water. Rinse and wipe dry with a soft cloth.
Do not use razor blades or other sharp instruments that can
7
Before calling for service, review this list. It may save you time and expense. This list
includes common occurrences that are not the result of defective workmanship or
materials in this appliance.
TROUBLESHOOTING
GUIDE
PROBLEM
CAUSE
CORRECTION
APPLIANCE OPERATION
Appliance does not run.
Appliance is plugged into a
circuit that has a ground fault
Temperature control is in the
"OFF" position.
Appliance may not be plugged in,
or plug may be loose.
Use another circuit. If you are unsure about the
outlet, have it checked by a certified technician.
See Thermostat Setting.
*
*
*
*
*
*
*
*
Ensure plug is tightly pushed into outlet.
House fuse blown or tripped
circuit breaker.
Check/replace fuse with a 15 amp time delay
fuse. Reset circuit breaker.
Power outage
Room or outside weather is hot.
Check house lights. Call local Electric Company.
It's normal for the appliance to work harder under
these conditions.
*
*
*
*
Appliance runs too much
or too long.
Appliance has recently been
disconnected for a period of time. completely.
Large amount of warm or hot
food have been stored recently.
Door is opened too frequently or
kept open too long.
It takes 24 hours for the appliance to cool down
*
*
*
*
Warm food will cause appliance to run more until
the desired temperature is reached.
Warm air entering the appliance causes it to run
more. Open the door less often.
*
*
Appliance door may be slightly
Temperature control is set too
low.
Appliance gaskets are dirty,
worn, cracked or poorly fitted.
See "Door Problems".
*
*
*
*
Turn control knob to a warmer setting. Allow
several hours for the temperature to stabilize.
Clean or change gasket. Leaks in the lid seal will
cause appliance to run longer in order to maintain
desired temperature.
*
*
Interior appliance
temperature is too cold.
Interior appliance
Temperature control is set too
low.
Temperature control is set too
warm.
Door is opened too frequently or
kept open too long.
Turn control knob to a warmer setting. Allow
several hours for the temperature to stabilize.
Turn control knob to a colder setting. Allow several
hours for the temperature to stabilize.
Warm air entering the appliance causes it to run
more. Open the door less often.
*
*
*
*
*
*
temperature is too warm.
Appliance door may be slightly
Large amount of warm or hot
food have been stored recently.
Appliance has recently been
See "Door Problems".
Wait until the appliance has had a chance to
reach its selected temperature.
*
*
*
*
appliance requires 24 hours to cool down
*
*
*
disconnected for a period of time. completely.
Appliance external
surface temperature is
warm.
The external appliance walls can
be as much as 30ºF warmer than
room temperature.
This is normal while the compressor works to
transfer heat from inside the appliance cabinet.
*
SOUND AND NOISE
Louder sound levels
whenever appliance is
on.
Modern appliances have
increased storage capacity and
more stable temperatures. They
require heavy duty compressors.
Appliance operates at higher
pressures during the start of the
ON cycle.
Metal parts undergo expansion
and contraction, as in hot water
pipes.
This is normal. When the surrounding noise level
is low, you might hear the compressor running
while it cools the interior.
*
*
Louder sound levels
when compressor
comes on.
Popping or cracking
sound when compressor
comes on.
This is normal. Sound will level off or disappear
as appliance continues to run.
*
*
*
*
This is normal. Sound will level off or disappear
as appliance continues to run.
8
PROBLEM
CAUSE
CORRECTION
SOUND AND NOISE (Cont.)
Bubbling or gurgling soun Refrigerant (used to cool
This is normal.
*
*
*
*
appliance) is circulating
Vibrating or rattling noise.
Appliance is not level. It rocks on
the floor when it is moved
Floor is uneven or weak.
Level the appliance by putting wood or metal
shims under part of the appliance.
Ensure floor can adequately support appliance.
Level the appliance by putting wood or metal
shims under part of the appliance.
*
*
appliance is touching the wall.
Re-level appliance or move appliance slightly.
*
*
*
WATER / MOISTURE / FROST INSIDE APPLIANCE
Moisture forms on inside
appliance walls.
Weather is hot and humid, which
increases internal rate of frost
build-up.
This is normal.
*
Door is slightly open.
Door is kept open too long or is
opened too frequently.
See "Door Problems".
Open the door less often.
*
*
*
*
ODOR IN APPLIANCE
Odors in appliance.
Interior needs to be cleaned.
Clean interior with sponge, warm water, and
baking soda.
Cover the food tightly.
*
*
*
*
Foods with strong odors are in
the appliance.
DOOR PROBLEMS
Door will not close.
Appliance is not level. It rocks on
the floor when it is moved
slightly.
Level the appliance by putting wood or metal
shims under part of the appliance.
*
*
*
*
Floor is uneven or weak.
Ensure floor can adequately support appliance.
Level the appliance by putting wood or metal
shims under part of the appliance.
LIGHTING PROBLEMS
Light bulb is not on.
The fluorescent lamp or light
bulb is burned out.
No electric current is reaching
the appliance.
See "Fluorescent Lamp" or "Interior Light" on
Features Section.
See "appliance Does Not Run".
*
*
*
*
9
IMPORTANT SAFETY NOTICE
The information provided herein is designed to assist qualified repair personnel only. Untrained
persons should not attempt to make repairs due to the possibility of electrical shock. Disconnect
the power cord before servicing.
ELECTRICAL CIRCUIT
STAINLESS STEEL DOOR
REFRIGERATOR
GLASS DOOR
REFRIGERATOR
STAINLESS STEEL DOOR
FREEZER
IMPORTANT
IF ANY GREEN GROUNDING WIRES ARE REMOVED DURING SERVICING, THEY MUST BE
RETURNED TO THEIR ORIGINAL POSITION AND PROPERLY SECURED.
10
Commercial Appliance Warranty Information
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to
be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. All labor costs on commercial laundry products.
2. Payment acceptance devices for commercial laundry products.
3. Products with original serial numbers that have been removed, altered or cannot be readily determined.
4. Normal wear and tear and gradual deterioration.
5. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
6. Rust on the interior or exterior of the unit.
7. Products purchased “as-is”.
8. Food loss due to any refrigerator or freezer failures.
9. Damage caused at any time during shipment.
10. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances used
other than in accordance with the provided instructions.
11. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
12. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc.,
which are not a part of the appliance when it is shipped from the factory.
13. Service calls to replace appliance light bulbs, air filters, water filters, other consumables, or knobs, handles, or
other cosmetic parts.
14. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip charges,
or mileage expense for service calls to remote areas, including the state of Alaska.
15. Damages to the finish of appliance and/or location that are incurred during installation, including but not limited
to floors, cabinets, walls, etc.
16. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine
Electrolux parts or parts obtained from persons other than authorized service companies; or external causes
such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
17. Labor costs after ninety (90) days from your original date of purchase incurred for product repair or replacement
as provided herein for appliances operated by a concessionaire or vendor in a trailer or other motorized vehicle
or at varying locations.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR.
ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS
PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN
LIMITED WARRANTY OR ANY IMPLIED WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE
DURATION OF IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO
YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER
RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada
Corp. Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and
parts under this warranty must be performed by Electrolux or an authorized service company. Product features or
specifications as described or illustrated are subject to change without notice.
USA
Canada
1.866.738.1640
1.866.738.1640
Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
11
|