Foundations Baby Furniture 100 EHBP User Manual

Model 100-EHBP  
Horizontal Diaper Changing Station  
with EZ MountBacker Plate  
Installation Instructions  
Thank you for purchasing a quality Foundations® product. Our goal is 100% consumer satisfaction!  
If, for any reason you are not satisfied or if you have questions regarding your product or installation,  
please contact our customer service team at 1-877-716-2757. Please DO NOT contact your distributor  
or reseller as we are better prepared to assist you.  
WARNING  
Failure to follow these warnings and the installation instructions could result in serious injury  
or death.  
Read all instructions before installing diaper changing station. Keep these instructions. DO NOT  
discard.  
SI253D  
 
WARNING  
A stud MUST be located and used for at least one side of the diaper changing station.  
The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore, MUST be  
firmly secured in order to support the weight they are intended to support. Contact an architect or building contractor  
if any questions.  
INSTALLATION  
NOTE: If using a backer plate, go to “Using Backer Plate Mounting System” section.  
1. Locate wood stud where left side of changing station will be mounted to the wall.  
Flat  
Wood Stud  
Washer  
2. Measure up 46” (117 cm) from the floor and mark the wall. This locates the position  
for the top left attachment hole.  
Finishing  
Washer  
NOTE: Mark on wall MUST be in center of wood stud.  
3. Align hole in top left corner of changing station with mark on wall and hold in place.  
Wood  
Screw  
4. Using a level and measuring tape, mark the remaining three (3) holes. After marking holes,  
set changing station down on ground.  
Fig. a  
Changing  
Station  
5. Use a power drill and appropriate bit to drill four (4) holes in the wall. This may require  
2 people.  
NOTE 1: For wood studs:  
Toggle  
Anchor  
- If finished wall surface is tile or masonry over wood studs, use  
a 7/32” masonry bit for the pilot hole until you hit the wood  
stud, then change to 1/8” bit.  
- Use wood screws, finishing washers and flat washers (Fig. a).  
Wood Stud  
Flat  
Washer  
Changing  
Station  
NOTE 2: For use with toggle anchors:  
- If finished wall surface has wood studs that are not 16” on center,  
has metal studs, or has an underlying surface of concrete block,  
use 1/2” bit.  
- Use machine screws and flat washers (Fig. b).  
Machine  
Screw  
Fig. b  
- For holes NOT located in a wood stud, toggle anchors MUST be  
used (Fig. c). See “Using Toggle Anchors” section.  
6. Align holes in changing station with drilled holes and secure top left corner of changing  
station to wall stud using the appropriate screw and washer. Continue to secure the  
three (3) remaining corners using the appropriate screws and washers as described  
in Note 1 or Note 2.  
Fig. c  
WARNING  
All 4 of these locations MUST be used for safe installation. The lower holes ensure  
installation through the metal brackets.  
7. Ensure all four (4) screws are tight and snap caps over screw heads.  
Using Toggle Anchors:  
Toggle  
Anchor  
Wood Stud  
1. Insert metal end of toggle anchor into 1/2” hole.  
2. Slide zip strip down snugly against wall.  
3. Snap off break-away pieces of toggle anchor (Fig. d).  
Break-Away  
4. Align holes in changing station with toggle anchors and secure top left corner of changing station to  
wall using machine screws and flat washers. Continue to secure the three (3) remaining corners  
using machine screws and flat washers.  
Fig. d  
5. Ensure all four (4) screws are tight and snap caps over screw heads.  
2
 
RECOMMENDED BLOCKING:  
Top  
If the walls do not have studs on center, then additional blocking  
is necessary (Fig. e).  
8 1/4"  
(210 mm)  
Contact an architect or building contractor to make sure the blocking  
is adequate and complies with building codes.  
For A. D. A.  
Compliance  
46”  
OPERATION:  
(117 cm)  
32"  
(813 mm)  
on center  
Rotate base downward. Place infant on top of the changing surface.  
Use restraint system as described below. After child has been changed,  
remove restraint system and rotate base back up against the wall.  
Fig. e  
A. F. F  
USE OF RESTRAINT SYSTEM:  
Place child so restraint strap is located at abdomen. Rotate top of buckle upward and insert strap  
in buckle. Pull strap through buckle until snug against infant. Rotate top of buckle downward to lock  
the strap into place. Slide red locking tab over top of buckle (Fig.f). Reverse steps to loosen strap.  
Locking  
Tab  
Top Of  
Buckle  
MAINTENANCE AND CLEANING:  
Check all hardware and components monthly or as required to ensure hardware is tight and there  
are no missing or damaged components. Take unit out of service if any component is missing or  
damaged and contact customer service to order replacement parts. Do not substitute parts.  
For replacement parts, contact customer service at 1-877-716-2757.  
Clean by using a damp cloth with mild soap or mild multi-purpose cleaner. Do not use any strong  
chemical cleaners or cleaning agents that may be hazardous to children.  
Fig. f  
WARNING  
Child should never be left unattended.  
Avoid serious injury from falling or sliding out. Always use restraint system.  
Adding excessive weight such as parcels, packages, or accessories to the unit or to the bag hooks that exceed the total  
weight limit of 50 pounds (22.7 kg) may cause the unit to be unstable or may cause a hazardous unstable condition to  
exist.  
Using Backer Plate Mounting System:  
If your changing station was supplied with a backer plate, please follow these instructions. If a backer plate was not supplied and you  
would like to order one, see information on page 1.  
The backer plate is designed to enhance the attachment method to ensure that at least one wood stud is used to support the changing  
station.  
WARNING  
A stud MUST be located and used for at least one side of the diaper changing station.  
The diaper changing station is no stronger than the anchors or walls to which they are attached and, therefore, MUST be  
firmly secured in order to support the weight they are intended to support. Contact an architect or building contractor  
if any questions.  
Use backer plate mounting system with at least four (4) standard mounting screws. The backer plate alone is NOT a  
secure attachment method.  
1. Locate wood stud where left side of changing station will be mounted  
to the wall.  
2. Measure up 46” (117 cm) from the floor and mark the wall.  
NOTE: Mark on wall MUST be in center of wood stud.  
3. Using two (2) 3” wood screws and a level, mount the backer plate to the  
center of the wood stud (Fig. g).  
NOTE: The lip of the backer plate MUST be facing away from the wall (Fig. h).  
Repeat steps to secure backer plate to another stud on the opposite side.  
4. Slide recessed area on back of changing station onto lip of backer plate.  
5. Return to installation step 5.  
Fig. g  
Side view of  
Backer Plate  
Backer  
Plate Lip  
Fig. h  
3
 

Earlex Paint Sprayer ASG55 User Manual
Electro Voice Microphone Cobalt Co9 User Manual
Exido Hot Beverage Maker 245 065 User Manual
Extron electronic Projector Accessories PCM340 User Manual
Extron electronic Stereo System MHR 2 User Manual
Fisher Price Car Seat N9327 User Manual
Focal Car Amplifier Solid 4 User Manual
Focal Car Speaker 33 WX User Manual
Gateway Flat Panel Television GTW L17M103 User Manual
Gigabyte Personal Computer GA K8VT800M User Manual