DIRECT LINK
PRIVACY MONITOR
TM
Model Number: 71592
For proper setup and use, please read these instructions and keep them for future reference.
Includes two AC adaptors to power the transmitter and receiver.
The transmitter and receiver also run on battery power. (Transmitter requires four “C” (LR14)
alkaline batteries - not included; receiver requires one 9V (6LR61) alkaline battery - not included).
Adult assembly is required to install batteries (if used).
™
DIRECT LINK PRIVACY MONITOR FEATURES
Your Fisher-Price® Direct Link Privacy Monitor™ is equipped with a custom voice scrambling system that provides privacy
protection in your home. Although no system is completely private, your Fisher-Price® Direct Link Privacy Monitor™ has two
channels and 31 different codes to block out other listeners to protect your privacy.
6
20
5
2
3
21
16
14
12
13
9
22
11
7
8
15
17
4
19
1
10
18
1
2
Transmitter . . . . . . . . . . . . . . . . . .Sends (transmits) sounds to the receiver.
Power Switch . . . . . . . . . . . . . . . .Turns the transmitter power ON or OFF.
3
4
Power Indicator . . . . . . . . . . . . . .Lights up to let you know the transmitter is ON.
Microphone . . . . . . . . . . . . . . . . . .For clear audio pick-up.
5
6
7
8
9
2-Position Channel Switch . . . . . .Allows you to change channels when interference occurs.
Flexible Antenna . . . . . . . . . . . . . .Aids in sound transmission.
AC Adaptor Socket . . . . . . . . . . . .For use with the provided AC adaptor.
Code Switch . . . . . . . . . . . . . . . . .Allows you to block out other listeners to protect your privacy.
Battery Compartment Door . . . . .For easy access to battery compartment.
Receiver . . . . . . . . . . . . . . . . . . . .Receives signal from the transmitter to hear sound.
Signal Indicator . . . . . . . . . . . . . .Lights up to let you know you’re “connected” to baby.
Power/Volume Dial . . . . . . . . . . . .Turns the receiver power ON or OFF. Controls the volume of sound.
Power Indicator . . . . . . . . . . . . . . .Lights up to let you know the receiver is ON.
Variable Lights Display . . . . . . . .Shows sounds are being transmitted.
10
11
12
13
14
15
16
17
Speaker . . . . . . . . . . . . . . . . . . . . .Allows you to hear baby’s sounds.
2-Position Channel Switch . . . . . .Allows you to change channels when interference occurs.
AC Adaptor Socket . . . . . . . . . . . .For use with the provided AC adaptor.
18
19
20
21
22
Code Switch . . . . . . . . . . . . . . . . .Allows you to block out other listeners to protect your privacy.
Battery Compartment Door . . . . .For easy access to battery compartment.
Flexible Antenna . . . . . . . . . . . . . .Aids in sound reception.
Belt Clip (on back) . . . . . . . . . . . . .For added portability when moving from room to room.
AC Adaptors (2 included) . . . . . .Both the transmitter and receiver operate on standard household current
(120V AC outlet) with these AC adaptors.
3
BATTERY INSTALLATION (OPTIONAL)
The transmitter and receiver operate with either the AC adaptors (included) or by battery power.
Four “C” Alkaline Batteries
9V
(6LR61)
Battery
Compartment
Door
1.5 V x 4
“C” (LR14)
+
-
TRANSMITTER
Both Shown Actual Size
• Locate the battery compartment door on the back of
the transmitter.
• Push the battery compartment door in the direction of the
arrow to open.
• Insert four, fresh “C” alkaline batteries as shown inside the
battery compartment.
• Close the battery compartment door.
Battery Compartment Door
9V Alkaline Battery
Battery Tips
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard
(carbon-zinc) or rechargeable (nickel-cadmium).
5
4
3
2
1
• Remove batteries during long periods of non-use. Always
remove exhausted batteries from the product. Battery
leakage and corrosion can damage the product. Dispose
of batteries properly.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended
in the “Battery Installation” instructions are to be used.
• If removable rechargeable batteries are used, they are only to
be charged under adult supervision.
• Rechargeable batteries are to be removed from the product
before they are charged.
• If you use a battery charger, it should be examined regularly
for damage to the cord, plug, enclosure and other parts.
Do not use a damaged battery charger until it has been
properly repaired.
RECEIVER
• Locate the battery compartment door on the back of
the receiver.
• Push the battery compartment door in the direction of the
arrow to open.
• Snap the terminals of a fresh 9V alkaline battery into
the connectors.
• Close the battery compartment door.
4
SETUP
For your convenience, the channel and code switches on the transmitter and receiver have been pre-set at Fisher-Price®.
IMPORTANT! To prevent entanglement, never place the transmitter in a crib or playpen.
Place the transmitter, receiver and AC adaptor cord(s) out of baby’s reach.
Antenna
Antenna
AC Adaptor
AC Adaptor
Channel Switch
Channel Switch
Socket
Socket
AC Adaptor Jack
AC Adaptor Jack
TRANSMITTER
RECEIVER
• Decide whether you will use the AC adaptor or batteries to
power the transmitter/receiver. If you will be using either unit
near an outlet, we recommend using the AC adaptor(s).
• Place the receiver where you can hear/see it. Or, wear the
receiver using the convenient belt clip. Make sure the antenna
points upward for best reception.
• Place the transmitter in the same room with your child. For
best sound pick-up, point the microphone directly toward the
crib or play area. Make sure the antenna points upward for
best transmission.
• For best reception, unwrap and fully extend the AC adaptor
cord. Insert the AC adaptor jack into the receiver socket. Insert
the plug into a standard wall outlet.
• Check to be sure the channel switch on both the receiver and
• For best transmission, unwrap and fully extend the AC adaptor
cord. Insert the AC adaptor jack into the transmitter socket.
Insert the plug into a standard wall outlet.
the transmitter are on the same channel.
5
CHECKING PRIVACY
Power Switch
Power Indicator
Channel Switch
Power/Volume Dial
Power Indicator
Signal
Indicator
RECEIVER
TRANSMITTER
• Rotate the power/volume dial on the receiver to the ON
position. The power indicator lights.
• Re-set the channel switches on both the transmitter and the
receiver to the same channel.
• Make sure the power switch on the front of the transmitter is
in the OFF position. The power indicator should NOT light.
• Look at the signal indicator on the receiver. It should NOT light.
IMPORTANT! If the signal indicator lights on either channel (with
the transmitter power OFF), you need to reset your scrambled
code. Please see Resetting Your Scrambled Code, page 8.
• Change the channel switch on the receiver to the other channel.
• Look at the signal indicator on the receiver. It should NOT light.
If the signal indicator does NOT light on either channel (with
the transmitter power OFF), the privacy feature on your Direct
Link Privacy Monitor™ is working.
6
USE
Power Switch
Channel
Switch
Channel Switch
Power Indicator
Power
Indicator
Variable Lights
Display
Power/
Volume Dial
Signal
Indicator
RECEIVER
TRANSMITTER
• Slide the power switch on the front of the transmitter to the
ON position. The power indicator lights.
• The variable lights display will light when sound is received by
the receiver.
• Rotate the Power/Volume dial on the receiver to the “ON”
position. The power indicator lights.
• If all five bars in the variable lights display light and there is a
high level of static:
• Check to be sure the signal indicator on the receiver lights. If
the signal indicator on the receiver does not light, you need to
reset your scrambled code. Please see Resetting Your Scrambled
Code, page 8.
– The receiver power is ON and the transmitter power is OFF.
(Turn the transmitter power ON.)
– The receiver is out of range of the transmitter. (Move the
receiver closer to the transmitter.)
• Adjust the volume to a comfortable level on the receiver.
– The receiver and the transmitter are not on the same channel.
(Set the channel switches on the transmitter and receiver to
the same channel.)
– Loud sounds are transmitting.
Note: The variable lights display will not light if the battery
is weak, even though you may still hear sounds. Replace the
battery with a fresh 9V alkaline battery, or use the AC adaptor
that came with this product.
• To further enhance the privacy of your home, be sure to turn
the transmitter and receiver OFF when not in use.
7
SOUND RECEPTION
It is very important to test the sound reception of the
Direct Link Privacy Monitor™ before first-time use
and whenever you change the location of the transmitter.
• Test the Direct Link Privacy Monitor™ transmission and
reception. Have an adult speak into the transmitter in the room
you intend to use the transmitter. (If an adult is not available,
use a ticking clock or radio.) Place the receiver in the room in
which you intend to use the receiver. Adjust the receiver
location or volume dial until you hear sounds clearly through
the receiver.
• If you experience interference (buzzing, static, etc.) while using
one channel setting, switch both units to the other channel.
Selecting a channel is usually a one-time adjustment.
• If interference occurs on both channels or if further problems
develop, please refer to the Problems and Solutions Guide
beginning on page 10.
RESETTING YOUR SCRAMBLED CODE
Code
Switches
5
4
4
3
3
2
2
1
1
Battery
Compartment
Door
Code
Switches
Battery
Compartment
Door
1
2
3
4
5
1
2
3
4
5
TRANSMITTER
RECEIVER
IMPORTANT!
- Do not use a pencil to move the code switches.
• Check to be sure the channel switch on both the receiver and
the transmitter are on the same channel.
• Locate the battery compartment doors on the back of the
receiver and the transmitter.
• Push the battery compartment doors in the direction of
the arrow to open them.
• If you are using battery power in either unit, remove
the batteries.
• Using a pen, push the code switches up or down to change
your scrambled code. Make sure the code switches in the
transmitter and receiver match.
- Do not position all five code switches in the OFF (down)
position. When the code switches in the transmitter are all in
the OFF (down) position, the scrambling feature is disabled.
• If you are using battery power in either unit, re-install
the batteries.
• Slide the power switches on the front of the transmitter and
receiver to the ON position. The power indicators light.
• Check to be sure the signal indicator on the receiver lights. If
the signal indicator on the receiver does not light, you have not
reset the code switches correctly. Please re-read this section
carefully and reset the code switches.
8
CARE
• Keep the transmitter and receiver free from dust.
FCC NOTE
(UNITED STATES ONLY)
• The outer surface of the transmitter, receiver and AC adaptors
can be cleaned with a cloth lightly dampened with a mild
cleaning solution.
• Do not immerse any part of the transmitter, receiver or
AC adaptors.
Direct Link Privacy Monitor™
Model Number: 71592
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Fisher-Price, Inc.
Consumer Relations Department
636 Girard Avenue
East Aurora, New York 14052
9
PROBLEMS AND SOLUTIONS
IMPORTANT! If you have a problem with the Direct Link Privacy Monitor™, first check the Problems and Solutions Guide. If you
still experience a problem with the Direct Link Privacy Monitor™, please call Fisher-Price® Consumer Relations at 1-800-432-KIDS.
PROBLEM
PROBABLE CAUSE
SOLUTION
Transmitter power
indicator does not light
Transmitter not turned ON
Turn the transmitter ON.
Power is turned OFF
Make sure that any light switches that control power flow to the wall
outlet are ON.
Make sure house fuses and circuit breakers are ON.
AC adaptor not properly connected
AC adaptor problem
Check AC adaptor jack-to-socket and plug-to-outlet connections.
Test the transmitter using the other AC adaptor included with this product.
®
If the transmitter works with the other AC adaptor, contact Fisher-Price
to replace the broken AC adaptor.
Weak or dead batteries
Replace the batteries in the transmitter with four, fresh “C” alkaline batteries
or use AC adaptor.
Receiver power
indicator does not light
Receiver not turned ON
Power is turned OFF
Turn the receiver ON.
Make sure that any light switches that control power flow to the wall
outlet are ON.
Make sure house fuses and circuit breakers are ON.
AC adaptor not properly connected
AC adaptor problem
Check AC adaptor jack-to-socket and plug-to-outlet connections.
Test the receiver using the other AC adaptor included with this product.
®
If the receiver works with the other AC adaptor, contact Fisher-Price
to replace the broken AC adaptor.
Weak or dead battery
Replace the battery in the receiver with a fresh 9V alkaline battery or
use the AC adaptor.
No sound
Channel switches not on same
setting (channel)
Set channel switch on transmitter and receiver to the same channel.
Signal interference due to monitors,
cordless telephones, etc.
Change the channel setting on both the transmitter and the receiver.
Identify and eliminate the source of interference.
Test reception by moving the transmitter and/or receiver to different locations
throughout the house. Relocate the transmitter and/or receiver.
Out of range or insufficient signal
Test reception by moving the transmitter and/or receiver to different locations
throughout the house. Relocate the transmitter and/or receiver.
Volume not turned up
Adjust volume control on receiver.
Improper antenna position
Make sure the antenna on the transmitter and receiver are pointing upward.
Weak or dead batteries
Replace the battery in the receiver with a fresh 9V alkaline battery, and
the batteries in the transmitter with four “C” alkaline batteries, or use
the AC adaptors for a power source.
AC adaptor not properly connected
Check AC adaptor jack-to-socket and plug-to-outlet connections.
10
PROBLEMS AND SOLUTIONS
PROBABLE CAUSE
PROBLEM
SOLUTION
Weak reception
Out of range or insufficient signal
Test reception by moving the transmitter and/or receiver to different locations
throughout the house. Relocate the transmitter and/or receiver.
AC adaptor cord(s) not fully extended
Improper antenna position
Fully extend AC adaptor cord(s).
Make sure antennas are pointing upward.
Receiver variable lights
display does not light
Weak or dead battery in receiver
Replace the battery in the receiver with a fresh 9V alkaline battery or
use the AC adaptor.
Interference
Signal interference due to another
nursery monitor or cordless
telephone, etc.
Change channel switch on both transmitter and receiver to the other channel.
(buzzing, static, etc.)
and signal indicator on
receiver is ON
Channel switches not on same
setting (channel)
Set channel switch on transmitter and receiver to the same channel.
Interference
Signal interference due to other
nursery monitors or cordless
telephones, etc.
Change channel switch on both transmitter and receiver to the to the
(buzzing, static, etc.)
and signal indicator on
receiver is OFF
other channel.
Identify and eliminate source of interference. Do not use more than one
transmitter at the same time in the same house.
Channel switches not on same
setting (channel)
Set channel switch on transmitter and receiver to the same channel.
Make sure the transmitter is ON. The power indicator should be lit.
Reset code switches in receiver and transmitter so that they match.
Receiver power is ON but transmitter
power is OFF
Code switches in receiver and
transmitter do not match
Interference
Signal interference due to another
Fisher-Price Direct Link Privacy Monitor
Make sure transmitter power is ON.
®
™
(garbled voices) and
signal indicator on
receiver is ON
Change channel switch on both transmitter and receiver to the other channel.
We recommend “Checking Privacy” periodically. See page 6.
Move receiver further away from transmitter.
Feedback
(squealing or whistling)
Receiver is too close to the transmitter
Volume is set too high
Lower volume on the receiver.
Turn the transmitter power ON.
All five bars on the
receiver variable lights
display light
Receiver power is ON but
transmitter power is OFF
Out of range or insufficient signal
Move the receiver closer to the transmitter.
Channel switches not on same
setting (channel)
Set channel switches on transmitter and receiver to the same channel.
AC adaptor not properly connected
to transmitter
Check AC adaptor jack-to-socket and plug-to-outlet connections.
11
ONE (1) YEAR
CONSUMER
LIMITED WARRANTY
INFORMATION
Occasionally a consumer may experience a problem with one
of our products. If this should happen, please call us toll-free,
rather than return this product to the store. Usually we can solve
the problem on the telephone or by sending you replacement
parts. Please call Fisher-Price® Consumer Relations, toll-free at
1-800-432-KIDS, 8 AM-6 PM EST Monday through Friday.
Hearing-impaired consumers using TTY/TDD equipment, please
call 1-800-382-7470. Or, write to: Fisher-Price® Consumer
Relations, 636 Girard Avenue, East Aurora, New York 14052.
Fisher-Price, Inc., 636 Girard Avenue, East Aurora, New York
14052, warrants to the original owner that the Direct Link Privacy
Monitor™ is free from all defects in material and workmanship
when used under normal conditions for a period of one (1) year
from the date of purchase.
Should the product fail to perform properly, we will repair or
replace it at our option, free of charge. Purchaser is responsible
for shipping the product to Fisher-Price Consumer Relations at
the address indicated above and for all associated freight and
insurance cost. Fisher-Price, Inc. will bear the cost of shipping the
repaired or replaced item to you. This warranty is void if the
owner repairs or modifies the product. This warranty excludes any
other liability other than that expressly stated above including
but not limited to any incidental or consequential damages.
SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND
YOU MAY ALSO HAVE OTHER LEGAL RIGHTS WHICH VARY
FROM STATE TO STATE.
If you have any questions about this product: In Canada, call 1-800-567-7724, or write to: Mattel Canada Inc., 6155 Freemont Blvd., Mississauga, Ontario L5R 3W2.
In Great Britain, telephone 01628 500303.
In Australia, call the Fisher-Price Australian Consumer Advisory Service toll-free at 1-800-800-812, or write to: Mattel Pty. Ltd., 658 Church Street, Locked Bag #870,
Richmond Victoria, 3121 Australia.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
71592pr-0920
©2000 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in China
|